AIRESPACE-SWITCHING-MIB Download

agentInventorySysDescription

The switch's Inventory system description.

agentInventoryMachineType

Type of the Machine used in the Switch.

agentInventoryMachineModel

The switch's Machine Model.

agentInventorySerialNumber

Serial number of the switch.

agentInventoryMaintenanceLevel

The switch's Inventory Maintenance Level

agentInventoryBurnedInMacAddress

Burned-In MAC Address

agentInventoryOperatingSystem

Operating System running on this unit

agentInventoryManufacturerName

Name of the switch manufacturer.

agentInventoryProductName

Name of the product.

agentInventoryProductVersion

Version of the product.

agentInventoryIsGigECardPresent

True if the Switch contains a Gigabit ethernet card .

agentInventoryIsCryptoCardPresent

True if the switch is carrying a Crypto card.

agentInventoryIsForeignAPSupported

States whether the switch supports third party Access Points.

agentInventoryMaxNumberOfAPsSupported

Maximum number of APs supported with this Controller.

agentInventoryIsCryptoCard2Present

True if the switch is carrying second Crypto card for 4400 controller.

agentInventoryFipsModeEnabled

True if FIPS (Federal Information Processing Standards) mode has been enabled on the controller.False if FIPS mode has not been enabled. FIPS mode can only be enabled through console.

agentTrapLogTotal

The total number of traps sent since last reset.

agentTrapLogTotalSinceLastViewed

The number of traps sent since last viewed.

agentRadioUpDownTrapCount

The total number of AP Up/Down traps sent since last reset.

agentApAssociateDisassociateTrapCount

The total number of AP Associate/Disassociate traps sent since last reset.

agentApLoadProfileFailTrapCount

The total number of AP Load Profile Failure traps sent since last reset.

agentApNoiseProfileFailTrapCount

The total number of AP Noise Profile Failure traps sent since last reset.

agentApInterferenceProfileFailTrapCount

The total number of AP Interference Profile Failure traps sent since last reset.

agentApCoverageProfileFailTrapCount

The total number of AP Coverge Profile Failure traps sent since last reset.

agentTrapLogTable

Agent Trap Log

agentTrapLogEntry

Agent trap log entry

agentTrapLogIndex

Unique index of trap entry

agentTrapLogSystemTime

System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.

agentTrapLogTrap

Description of the trap sent.

agentSwitchInfoLwappTransportMode

The LWAPP transport mode specifies if the switch is operating in Layer2 or Layer3 mode. This attribute gives the current mode the switch is operating on.

agentSwitchInfoPowerSupply1Present

This is to indicate if the switch has Power Supply 1 present on it. This is applicable to the 4200 series and will always return true for the earlier device versions.

agentSwitchInfoPowerSupply1Operational

This is to indicate if the switch's Power Supply 1 is operational. This is applicable to the 4200 series and will always return true for the earlier device versions.

agentSwitchInfoPowerSupply2Present

This is to indicate if the switch has Power Supply 2 present on it. This is applicable to the 4200 series and will always return false for the earlier device versions.

agentSwitchInfoPowerSupply2Operational

This is to indicate if the switch's Power Supply 2 is operational.This is applicable to the 4200 series and will always return false for the earlier device versions.

agentCurrentCPUUtilization

Current CPU Load of the switch in percentage.

agentTotalMemory

Total RAM of the switch in Kbytes.

agentFreeMemory

Free RAM of the switch in Kbytes.

agentWcpDeviceName

This is the name of the device this controller is residing on.

agentWcpSlotNumber

The slot number on the Wcp Device that this controller is residing on.

agentWcpPortNumber

The port number on the Wcp Device that this controller is residing on.

agentWcpPeerPortNumber

The port number of this controller's peer on the same slot on Wcp Device that this controller is residing on.

agentWcpPeerIpAddress

The IP Address of this controller's peer on the same slot on Wcp Device that this controller is residing on.

agentWcpControllerTableChecksum

This is the checksum that tracks the changes in the agentWcpControllerInfoTable. If there is any change in the information on this table, the checksum changes.

agentWcpControllerInfoTable

A table of the wireless controllers on a WCP device.

agentWcpControllerInfoEntry

Entry for a wireless controller on a WCP device.

agentWcpControllerInfoSlotNumber

The slot number on the Wcp device that a controller is residing on.

agentWcpControllerInfoPortNumber

The port number on the Wcp Device that a controller is residing on.

agentWcpControllerInfoIpAddress

The management IP Address of a controller.

agentLoginSessionTable

A table of the switch's login session

agentLoginSessionEntry

Login Session Entry

agentLoginSessionIndex

Agent Login Session Index of the switch

agentLoginSessionUserName

Agent Login Session UserName of the switch

agentLoginSessionIPAddress

Agent Login Session IP Address of the switch

agentLoginSessionConnectionType

Agent Login Session Connection Type of the switch

agentLoginSessionIdleTime

Agent Login Session Idle Time of the switch

agentLoginSessionSessionTime

Agent Login Session Time of the switch

agentLoginSessionStatus

Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.

agentTelnetLoginTimeout

Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 0 to 160. A value of 0 indicates that a Telnet sessi ...

agentTelnetMaxSessions

Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.

agentTelnetAllowNewMode

Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.

agentSSHAllowNewMode

Allow new SSH sessions (enable or disable) Config SSH disable means that no new SSH sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.

agentSerialTimeout

Agent Serial Timeout

agentSerialBaudrate

Agent Serial Baudrate

agentSerialCharacterSize

Agent Serial Character Size

agentSerialHWFlowControlMode

Agent Serial Hardware Flow Control.

agentSerialStopBits

Agent Serial Stop Bits

agentSerialParityType

Agent Serial Parity Type

agentLagConfigCreate

Agent Lag Create. When this object is set with a non-empty string, a new lag will be created.if possible with the entered string as it's name.

agentLagSummaryConfigTable

A summary table of the switch's lag config entries

agentLagSummaryConfigEntry

Switch's lag config entry

agentLagSummaryName

Agent Lag Name

agentLagSummaryLagIndex

Agent Lag If Index

agentLagSummaryFlushTimer

Agent Lag Flush Timer

agentLagSummaryLinkTrap

Agent Lag Link Trap

agentLagSummaryAdminMode

Agent Lag Admin Mode

agentLagSummaryStpMode

Agent Lag STP Mode

agentLagSummaryAddPort

Agent Lag Add Port. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.

agentLagSummaryDeletePort

Agent Lag Delete Port

agentLagSummaryPortsBitMask

Agent Lag Member Ports in bit mask representation

agentLagSummaryStatus

Agent Lag Status. active(1) - This Lag is enabled. destroy(6) - Set to this value to remove the Lag.

agentLagDetailedConfigTable

A detailed table of the switch's lag config entries

agentLagDetailedConfigEntry

Switch's lag config entry

agentLagDetailedLagIndex

Lag index

agentLagDetailedIfIndex

Lag port index

agentLagDetailedPortSpeed

Lag port speed. See agentPortType for description and list of valid values.

agentLagConfigMode

The Lag Mode on the 4400 series controller. When it is on, all the gigabit ports are bound to one aggregated link.

agentNetworkIPAddress

The switch's network ip address

agentNetworkSubnetMask

The switch's network subnet mask

agentNetworkDefaultGateway

The switch's network default gateway

agentNetworkBurnedInMacAddress

The switch's Burned-In MAC address

agentNetworkConfigProtocol

The switch's network config protocol

agentNetworkWebMode

The switch's web access mode.

agentNetworkSecureWebMode

If https is enable or not provided web mode is enabled

agentNetworkMulticastMode

Switch's ethernet multicast support. disable- multicast is disabled multicast - Multicast is enabled. unicast- Controller will convert multicast to unicast packet.

agentNetworkDsPortNumber

The switch's distribution port number.

agentNetworkUserIdleTimeout

Sets the idle user timeout.

agentNetworkArpTimeout

Sets the ARP entry timeout.

agentNetworkManagementVlan

VLAN ID of the network management interface.

agentNetworkGvrpStatus

The state of GVRP operation on the Switch. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabl ...

agentNetworkAllowMgmtViaWireless

This states whether Management via wireless is allowed or not.

agentNetworkBroadcastSsidMode

This mode when enabled allows WLAN SSIDs to be broadcasted.

agentNetworkSecureWebPassword

SSL Certificate Password. This can be optionally set while downloading SSL certificates of type Web Admin and Web Authentication

agentNetworkWebAdminCertType

Type of currently existing Web Admin Certificate installed on the Switch. It could be 'Empty' if the certificate is not present, 'Locally Generated' if the certificate is locally generated or it could have a name if it is downloaded externally.

agentNetworkWebAdminCertRegenerateCmdInvoke

This command when set to 'activate' will regenerate a Web Administration Certificate Locally that will replace the existing certificate.

agentNetworkWebAuthCertType

Type of currently exisitng Web Authentication Certificate installed on the Switch. It could be 'Empty' if the certificate is not present, 'Locally Generated' if the certificate is locally generated or it could have a name if it is downloaded externally.

agentNetworkWebAuthCertRegenerateCmdInvoke

This command when set to 'activate' will regenerate a Web Authentication Certificate Locally that will replace the existing certificate.

agentNetworkPeerToPeerBlockingMode

Mobile Peer to Peer Blocking mode on the switch.

agentNetworkMulticastGroupAddress

Multicast group address for access points.

agentNetworkRouteConfigTable

A table of the switch's Network Route entries

agentNetworkRouteConfigEntry

Switch's Network Route entry

agentNetworkRouteIPAddress

Network Route IP Address.

agentNetworkRouteIPNetmask

Network Route IP Netmask.

agentNetworkRouteGateway

Network Route IP Gateway.

agentNetworkRouteStatus

Network Route Row Status.

agentInterfaceConfigTable

A table of the switch's Interface Config entries Typically, it will contain entries for Service Port Interface, DS Port Interface and Virtual Gateway Interface apart from other entries.

agentInterfaceConfigEntry

Switch's Interface Config entry

agentInterfaceName

Interace Name. This values is 'management' for DS port, 'service-port' for service port and 'virtual' for virtual gateway. For other interfaces, the name can be anything. These interfaces are already created by default.

agentInterfaceVlanId

Vlan ID configured for the Interface.

agentInterfaceType

The interface's type. The static type is set for the interfaces that are created by default on the switch and these cannot be deleted. Any other interface that is created is of type dynamic which can be deleted.

agentInterfaceMacAddress

Interface MAC Address. This is only applicable in case of management and service-port interfaces.

agentInterfaceIPAddress

IP Address of the interface.

agentInterfaceIPNetmask

IP Netmask of the interface. This is 0 for the virtual interface.

agentInterfaceIPGateway

IP Gateway of the interface. This is 0 for virtual and service-port interface.

agentInterfacePortNo

A value 0 means the port is not set. The valid value can be any one of the physical ports on the switch. This is the primary port configured on the interface.

agentInterfacePrimaryDhcpAddress

Primary DHCP Server IP Address for the interface This applies to the management interface and other dynamic interfaces.

agentInterfaceSecondaryDhcpAddress

Secondary DHCP Server IP Address for the interface. This applies to the management interface and other dynamic interfaces.

agentInterfaceDhcpProtocol

The interface's DHCP protocol. This applies only to the service port interface.

agentInterfaceDnsHostName

The DNS host name for the Virtual Interface. This attribute is not valid for other interfaces.

agentInterfaceAclName

Name of the Access Control List applied to the interface. This attribute is applicable only to the management interface and other dynamic interfaces. If it is required to remove the ACL name for an interface, it should be set to an empty string.

agentInterfaceAPManagementFeature

When enabled, the dynamic interface can be used for AP management. SNMP support for AP management through dynamic interfaces has been introduced since '3.0.21.0' release. Only applicable to dynamic interfaces in 4200 series. In static interfaces, 'disabl ...

agentInterfaceActivePortNo

This is the currently active port for this interface.

agentInterfaceBackupPortNo

This values is valid only for the 4200 series of switches. The backup port is the port this interface is moved to once the primary port fails. A value 0 means the port is not set. The valid value can be any one of the physical ports on the 4200 switch.

agentInterfaceVlanQuarantine

This object is used to configure the health of the interface identified by agentInterfaceName. A value of 'true' is used to indicate that this particular interface is unhealthy. In this case, the data packets of the clients, that are assigned the VLAN Id ...

agentInterfaceRowStatus

The interface entry Row status.

agentNtpPollingInterval

Network Time Protocol polling interval. Min value is one hour and maximum is a week.

agentNtpServerTable

A summary table for switch's lag config entries

agentNtpServerEntry

Switch's NTP Server entry. Upto 4 entries may be added.

agentNtpServerIndex

NTP Server priority index.

agentNtpServerAddress

IP Address of the NTP Server

agentNtpServerRowStatus

NTP server entry row status.

agentDhcpScopeTable

A table listing the Scopes defined on the switch's DHCP Server.

agentDhcpScopeEntry

Switch's DHCP Server Scope entry.

agentDhcpScopeIndex

DHCP Scope Identifier Index.

agentDhcpScopeName

DHCP Scope Name.

agentDhcpScopeLeaseTime

DHCP Scope Lease time in seconds.

agentDhcpScopeNetwork

IP Address of the DHCP Scope Network. This is the address which is used to determine the DHCP scope a remote Switch is attaching to.

agentDhcpScopeNetmask

The DHCP Scope Netmask. This the subnet mask for the address pool.

agentDhcpScopePoolStartAddress

The DHCP Scope address pool start IP address.

agentDhcpScopePoolEndAddress

The DHCP Scope address pool end IP address.

agentDhcpScopeDefaultRouterAddress1

IP Address of the DHCP Scope's default Router 1.

agentDhcpScopeDefaultRouterAddress2

IP Address of the DHCP Scope's default Router 2.

agentDhcpScopeDefaultRouterAddress3

IP Address of the DHCP Scope's default Router 3.

agentDhcpScopeDnsDomainName

DNS Domain name for the DHCP Scope.

agentDhcpScopeDnsServerAddress1

IP Address of the DHCP Scope's DNS Server 1.

agentDhcpScopeDnsServerAddress2

IP Address of the DHCP Scope's DNS Server 2.

agentDhcpScopeDnsServerAddress3

IP Address of the DHCP Scope's DNS Server 3.

agentDhcpScopeNetbiosNameServerAddress1

IP Address of DHCP Scope's Netbios Name Server 1.

agentDhcpScopeNetbiosNameServerAddress2

IP Address of DHCP Scope's Netbios Name Server 2.

agentDhcpScopeNetbiosNameServerAddress3

IP Address of DHCP Scope's Netbios Name Server 3.

agentDhcpScopeState

DHCP Scope's State.

agentDhcpScopeRowStatus

Dhcp Scope entry row status.

agentServicePortIPAddress

The switch's Service Port IP address. (Service-port interface use is recommended instead of this group)

agentServicePortSubnetMask

The switch's Service Port subnet mask. (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)

agentServicePortDefaultGateway

Not Supported for release 1.0. The switch's Service Port default gateway. (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)

agentServicePortBurnedInMacAddress

The switch's Service Port Burned-In MAC address (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)

agentServicePortConfigProtocol

The switch's Service Port config protocol (Service-port interface in agentInterfaceConfigTable is recommended instead of this group)

agentSnmpTrapPortNumber

Snmp Trap Port Number

agentSnmpVersion1Status

Snmp Version 1 Status

agentSnmpVersion2cStatus

Snmp Version 2c Status

agentSnmpCommunityConfigTable

A table of the switch's SNMP community Config entries

agentSnmpCommunityConfigEntry

Switch's SNMP community Config entry

agentSnmpCommunityName

The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, th ...

agentSnmpCommunityIPAddress

The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Cli ...

agentSnmpCommunityIPMask

The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an aut ...

agentSnmpCommunityAccessMode

The switch's Snmp Community Access Mode Access Mode - This value can be readOnly or readWrite. A community with a read-only access allows for switch information to be displayed. A community with a readWrite access allows for configuration changes to be m ...

agentSnmpCommunityEnabled

If community is Enabled

agentSnmpCommunityStatus

The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP manager associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests usi ...

agentSnmpTrapReceiverConfigTable

Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported.

agentSnmpTrapReceiverConfigEntry

Switch's Snmp Trap Receiver Config entry

agentSnmpTrapReceiverName

The switch's Snmp Trap Receiver Name. This is the name of the remote network manager. the name can be up to 16 characters, and is case-sensitive.

agentSnmpTrapReceiverIPAddress

SNMP network Manager IP Address. The IP Address traps will be sent to. Each IP address parameter is four integer numbers. The numbers range from 0 to 255. After creation of entry IP Address cannot be changed.

agentSnmpTrapReceiverEnabled

The flag to enable the trap receiver. If disabled, no traps are sent to this receiver's IP Address.

agentSnmpTrapReceiverStatus

This object is used to create and delete instances of this table. The row, when created with the row status value of 'createAndGo' or 'createAndWait' is moved to the 'active' state automatically by the agent and remains in that state till the time the row ...

agentSnmpAuthenticationTrapFlag

Authentication Flag - Enable/Disable authentication Flag.

agentSnmpLinkUpDownTrapFlag

Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable.

agentSnmpMultipleUsersTrapFlag

Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session

agentSnmpSpanningTreeTrapFlag

Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps.

agentSnmpBroadcastStormTrapFlag

Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the ...

agentSnmpVersion3Status

Snmp Version 3 Status

agentSnmpV3UserConfigTable

User Config Table. Only creation and deletion of users is supported. All individual updates are not supported.

agentSnmpV3UserConfigEntry

User Config Entry

agentSnmpV3UserName

Agent User Name.

agentSnmpV3UserAccessMode

Agent User Access Mode

agentSnmpV3UserAuthenticationType

SNMPv3 User Authentication none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication

agentSnmpV3UserEncryptionType

SNMPv3 User Encryption Must be set to none(1) if agentSnmpV3UserAuthenticationType is set to none(1). Setting this object will set the encryption password to an empty string. none(1) - no encryption used des(1) - DES encryption used

agentSnmpV3UserAuthenticationPassword

SNMPv3 User Encryption Password

agentSnmpV3UserEncryptionPassword

SNMPv3 User Encryption Password

agentSnmpV3UserStatus

Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.

agentSpanningTreeMode

The switch's Spanning Tree Switch Status

agentSwitchAddressAgingTimeoutTable

The switch's address aging timeout table

agentSwitchAddressAgingTimeoutEntry

Aging information about a specific Filtering Database.

agentSwitchAddressAgingTimeout

The FDB entry's address aging timeout(in seconds)

agentSwitchBroadcastControlMode

The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds 20 percent of the link speed, the switch blocks (discard ...

agentSwitchDot3FlowControlMode

Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports.

agentSwitchLwappTransportMode

The LWAPP transport mode decides if the switch is operating in the Layer2 or Layer3 mode. The switch needs to be rebooted for the mode change to take effect.

agentTransferUploadMode

Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.

agentTransferUploadServerIP

Transfer upload tftpserverip configures the IP address of the server where the file will be uploaded. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.

agentTransferUploadPath

Transfer upload tftppath configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.

agentTransferUploadFilename

Transfer upload tftpfilename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less t ...

agentTransferUploadDataType

Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - System trace - Trap log - Crash File ::= { agentTransferUploadGroup 5 } SYNTAX INTEGER { enable(1), ...

agentTransferUploadStatus

Indicates the current status of an upload transfer.

agentTransferConfigurationFileEncryption

The configuration file can be encrypted before tftp upload from the switch and then decrypted before downloading to the switch when this option is enabled.

agentTransferConfigurationFileEncryptionKey

This is the key to be used when encrypting the configuration file while upload from the switch or while decrypting the file after download to the switch.

agentTransferDownloadMode

Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.

agentTransferDownloadServerIP

Transfer download tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.

agentTransferDownloadPath

Transfer download tftppath configures the directory path where the file is located. The switch remembers the last file path used.

agentTransferDownloadFilename

Transfer download tftpfilename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is les ...

agentTransferDownloadDataType

Transfer download datatype configures the type of file to downloaded to the switch. The types for download are: - Code - Configuration - Certificates - Signatures - customWebauth- custom webauth tar ball

agentTransferDownloadStart

Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.

agentTransferDownloadStatus

Indicates the current status of an download transfer.

agentTransferDownloadTftpMaxRetries

Maximum number of retries to be allowed for a TFTP message packet.

agentTransferDownloadTftpTimeout

Timeout in seconds for a TFTP message packet.

agentDot3adAggPortTable

This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.

agentDot3adAggPortEntry

Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port.

agentDot3adAggPort

ifIndex of this physical port

agentDot3adAggPortLACPMode

Enable/disable 802.3ad LACP on this port

agentPortConfigTable

A table of the switch's physical port config entries

agentPortConfigEntry

Switch's physical port config entry

agentPortDot1dBasePort

The port number of this port.

agentPortIfIndex

The switch's Port IfIndex

agentPortIanaType

The switch's Port Type

agentPortSTPMode

The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port

agentPortSTPState

The switch's Port Spanning Tree Protocol State

agentPortAdminMode

The switch's Port Admin Mode

agentPortPhysicalMode

The switch's Port Speed Mode. This is the configured physical mode.This object is read-only for gigabit ports

agentPortPhysicalStatus

The switch's Port Physical Speed Status.This is the current actual speed.

agentPortLinkTrapMode

If enabled, link up and link down traps will be sent for this port.

agentPortClearStats

Clear stats for this port only

agentPortDefaultType

This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of possible values for this object is the same as the set defined for the agentPortType object. This ob ...

agentPortType

This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ...

agentPortAutoNegAdminStatus

This object identifies the administration status of auto negotiation for this port.

agentPortDot3FlowControlMode

Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports.

agentPortPowerMode

Enable/Disable the port's Power over ethernet. This doesn't apply to appliances that have no POE controller.

agentPortGvrpStatus

The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disable ...

agentPortGarpJoinTime

The GARP Join time, in centiseconds.(Attribute no longer supported)

agentPortGarpLeaveTime

The GARP Leave time, in centiseconds.(Attribute no longer supported)

agentPortGarpLeaveAllTime

The GARP LeaveAll time, in centiseconds.(Attribute no longer supported)

agentPortMirrorMode

The switch's Port Mirror Mode. If enabled, then this is the port that the packets are mirrored to.

agentPortMulticastApplianceMode

The Port Multicast Appliance Mode. If enabled, then this port allows multicast streams through it. At a time, a maximum of four ports including the gigabit ethernet port can have this mode enabled on them. This is to limit the number of multicast streams ...

agentPortOperationalStatus

The current operational state of the port.

agentSaveConfig

save config to NVRAM

agentClearConfig

clear config to factory defaults

agentClearLags

clear lag configuration

agentClearLoginSessions

close all telnet sessions

agentClearPortStats

clear all port statistics

agentClearSwitchStats

clear all switch statistics

agentClearTrapLog

clear trap log

agentResetSystem

reset the switch

portStatsTable

A list of additional thernet statistics entries.

portStatsEntry

A collection of statistics kept for a particular Ethernet interface.

portStatsIndex

The value of this object uniquely identifies this portStatsEntry.

portStatsPktsTx64Octets

The total number of packets (including bad packets) transmitted that were 64 octets in length (excluding framing bits but including FCS octets).

portStatsPktsTx65to127Octets

The total number of packets (including bad packets) transmitted that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).

portStatsPktsTx128to255Octets

The total number of packets (including bad packets) transmitted that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).

portStatsPktsTx256to511Octets

The total number of packets (including bad packets) transmitted that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).

portStatsPktsTx512to1023Octets

The total number of packets (including bad packets) transmitted that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).

portStatsPktsTx1024to1518Octets

The total number of packets (including bad packets) transmitted that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).

portStatsPktsRx1519to1530Octets

The total number of packets (including bad packets) received that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets).

portStatsPktsTx1519to1530Octets

The total number of packets (including bad packets) transmitted that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets).

portStatsPktsTxOversizeOctets

The total number of packets (including bad packets) transmitted that were more than 1530 octets in length. (excluding framing bits but including FCS octets).

bsnSwitchingAgentInfoGroup

This collection of objects provide switching information.

bsnSwitchingAgentConfigGroup

This collection of objects provide switching configuration information.

bsnSwitchingAgentSystemGroup

This collection of objects provide switching system information and config.

bsnSwitchingAgentStatsGroup

This collection of objects provide switching statistics.

bsnSwitchingObsGroup

This collection of objects are obsoleted in bsnSwitching module.