BASIS-GENERIC-MIB Download

transId

Per card transaction ID. This object is used to keep track of configuration change on the card. The transId will be incremented by one for every configuration change on the card.

functionModuleHWRev

Hardware revision number for function Module.

functionModuleFWRev

Firmware revision number of the function Module.

functionModuleState

This object holds the status of a card in a particular shelf-slot. The possible values are : nocard(1) : card not present. standby(2) : card in standby state. The card is in ready state and will be ready to take over the service if the correspond ...

lineModuleSerialNum

This object contains Serial number of the line module.

lineModuleHWRev

This object contains Hardware revision for line module.

lineModuleFWRev

Firmware revision for line module. The current version does not have any firmware, hence will always contains zero length octet string.

lineModuleState

line module status.

moduleTrapAlarmSeverity

This object is sent to managers as part of all Trap PDUs, to determine the module alarm severity. An implementation may not support all the possible values. The Possible values are : major (1) : Major Service has been impacted minor (2) : Minor Serv ...

cardIntegratedAlarmBitMap

Bit position represents the different types of alarm for ASC: bit 0: ShelfFunctionModuleState (BNM only) (failed/boot/mismatch/heldinReset) bit 1: LineModuleState (BNM only) (notPresent/invalid) bit 2: ASMPhysicalAlarmState (BNM only) bit 3: ATMLMIFailure ...

hwHistory

RMA Test History - RMA Failure Code.

secLineModuleType

This object contains the type of secondary line module(back card). Physically it is the bottom card behind the backplane. Normally with connectors for physical devices. These are specific to the front or function modules. This Object is applicable only to ...

configChangeParentObjectIndex

Parent object index, could be - line index - port index This object will indicate the index of the immediate higher level object (line or port) of configChangeObjectIndex. This object is applicable only when configChangeObjectIndex represents a channel, p ...

configChangeSMSpecificObject

configChangeSMSpecificObject is a generic object which is Service Module Specific. It can be used for different purposes in different cards. The usage of the same with regard to very card type is listed below. FRSM-8T1E1 - used to store portDs0ConfigBitMa ...

interfaceNumOfValidEntries

Number of rows in interface Table The number represents the physcial interfaces the module has. ::= { cardInterface 2 } SYNTAX SEQUENCE OF InterfaceLineEntry ACCESS not-accessible STATUS mandatory DESCRIPTION This table has list of the physical interfaces ...

interfaceNumOfPortsPerLine

The number of physical ports of the line type. VISM has a port, but is not linked to these physical lines, hence value=0 is returned. DEFVAL {672} ::= { interfaceLineEntry 3 } SYNTAX INTEGER { other(1), ethernet-3Mbit (26), slip (28), frameRelay(32), atm( ...

riscXmtCtrlMsg

The number of control Frames transmitted to SAR (from RISC) maintained by RISC ::= { controlMsgCounter 1 } SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION The number of control Frames received from SAR (to RISC) maintained by RISC ::= { con ...

sarCtrlMsgLastUnkownChan

The control cell header Rcvd of the last unknown channel.

ctrlMsgClrButton

This object is used for clearing the messages in controlMsgCounter group.

chanNumOfValidEntries

Number of entries in the sar channel table ::= { sarChannelCounter 2 } SYNTAX SEQUENCE OF SarChannelCounterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION The table is for logical channels This table contains the counters for cells transmitted on ...

sarChannelCounterEntry

An entry for logical channel INDEX { sarShelfNum, sarSlotNum, sarChanNum } ::= { sarChannelCounterTable 1 } SarChannelCounterEntry ::= SEQUENCE { sarShelfNum INTEGER, sarSlotNum INTEGER, sarChanNum INTEGER, -- Xmt Cell stats xmtC ...

sarChanNum

BSC could have upto 4000 connections in this table ::= { sarChannelCounterEntry 3 } SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION The number of cells transmitted on this channel. ::= { sarChannelCounterEntry 4 } SYNTAX Counter ACCESS read-o ...

xmtCellsAIS

The number of AIS cells that were transmitted on this channel. ::= { sarChannelCounterEntry 6 } SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION The number of FERF cells that were transmitted on this channel. ::= { sarChannelCounterEntry 7 } S ...

xmtCellsEnd2EndLpBk

The number of End2End loop cells that were transmitted on this channel.

xmtCellsSegmentLpBk

The number of segment loop cells that were transmitted on this channel.

xmtCellsDiscShelfAlarm

The number of cells discard due to Shelfalarm on this channel. ::= { sarChannelCounterEntry 11 } -- receiver cell counters SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION The number of cells that were received on this channel. ::= { sarChanne ...

rcvCellsSegmentLpBk

The number of segment loop cells that were received on this channel.