CISCO-ASPP-MIB

CISCO-ASPP-MIB Download

MIBs list

The Cisco MIB for the asynchronous polled Communications protocol as implemented in the ASP Tunneling feature. This MIB provides information relating to the ASP interfaces in a router; the correspondin g tunnel interface can be accessed via CISCO-BSTUN-MIB.

IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for CISCO-ASPP-MIB

asppPortTable
A list of asynchronous interfaces which have been configured to support an asynchronous security protocol (ASP) BSTUN group.
asppPortEntry
Current ASP configuration settings for an asynchronous port.
asppPortProtocol
Specifies type of asynchronous security protocol being used. These protocols are implemented by individual security alarm manufacturers. There is no standard protocol for alarm communications over RS-232 interfaces. asyncGeneric(5)- provides generic polle ...
asppPortRole
Specifies the router's protocol role. primary(1) - Indicates we are attaching to the terminal or alarm panel. secondary(2) - Indicates we are attaching to the host or alarm console..
asppPortReceiveInterFrameTimeout
Specifies the receive inter-frame-timeout period, used to delimit frames. Since all the protocols are implemented over RS-232 3-wire circuits (ie TX, RX and GND), the only general method for start-end frame detection is to monitor the time between receive ...
asppPortDeviceAddressOffset
Specifies the byte offset within a frame, which contains the device address. This is used when the asynchronous interface is configured to use the async generic protocol handler. Because no knowledge of the protocol is built-in to the IOS, it must be told ...
asppPortEOFCharacter
Specifies the protocol character to use to delimit the end of a frame. The valid character is 0-255 and 256 indicates the object is not configured.
asppPortSOFCharacter
Specifies the protocol character to use to delimit the beginning of a frame. The valid character is 0-255 and 256 indicates the object is not configured.
asppPortIgnoreSequenceNumber
Specifies whether the asp sequence numbers used to synchronize aspp traffic between head-end and tail-end routers should be ignored. This is enabled if there isn't a one to one correlation between commands and responses between the two routers.
asppPortRspTimer
Specifies the amount of time the router will wait for a response to a packet before retransmission.
asppPortRxTimer
Specifies the maximum amount of time the router will wait for a complete packet to be received. It starts when an STX character is received.
asppPortHostTimer
Specifies the maximum amount of time the router will wait for a response to a terminal request from the host. It starts when a terminal request is forwarded to the host.
asppPortConnectTimer
Specifies the maximum amount of time the router will wait for the activation of the tunnel connection to the host to complete. It starts when a terminal requests a session with host.
asppPortRetryCount
Specifies the maximum number of timers a packet will be retransmitted before the connection with the terminal will be disconnected.
asppPortDelayEnq
Specifies the amount of time to wait after sending a connect packet to the the terminal before sending the ENQ to initiate a session
asppPortDisableEnq
Specifies whether sending of ENQ to initiate a session with the terminal is disabled.
asppPortSendAck
Specifies whether the router will send an ACK to acknowledge packets.
asppPortDirect
Specifies whether the line mode is direct or dialed. If in direct the router will immediately send ENQ without waiting for AT commands
asppPortDCDAlways
Specifies whether DCD should always be asserted or asserted only when the connection is active.
asppPortsGroup
A collection of objects providing information about interfaces that run asynchronous security protocols.
asppPortsGenericGroup
A collection of objects providing information about interfaces that run asynchronous generic protocols.
asppPortsAposGroup
A collection of objects providing information about interfaces that run asynchronous protocol to communicate to Point of Sale protocols.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list