CISCO-ATM-CONN-MIB Download

ciscoAtmVplTable

The Virtual Path Link extension Table.

ciscoAtmVplEntry

An entry in the Vpl table.This entry is used to model a bi-directional Vpl. This table augments the atmVplTable defined in RFC 1695. However it uses ifIndex and atmVplVpi as an Index for historical reasons. The entries are created/deleted as a by-product ...

ciscoAtmVplCastType

Vpl type is either a point to point connection or point to multipoint root or leaf.

ciscoAtmVplSpanType

Vpl span is either a transit one or a terminating one.

ciscoAtmVplConfigType

Vpl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only.

ciscoAtmVplRxUpcMode

Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection.

ciscoAtmVplConnState

The connection state of this VPL.

ciscoAtmVplOamLoopbkTxInterval

Frequency of OAM loopback cells generated.

ciscoAtmVplOamSegmentLoopback

Enable segment loopback on this virtual path.

ciscoAtmVplOamEndLoopback

Enable end to end loopback on this virtual path.

ciscoAtmVplOamAisEnable

Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual path.

ciscoAtmVplOamRdiEnable

Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received.

ciscoAtmVplInstallTime

The time stamp derived from sysUpTime when this VPL gets created. The VPL entries are created/deleted as a by-product of creating and deleting entries in the atmVplTable defined in RFC1695.

ciscoAtmVplInCells

VPL.

ciscoAtmVplOutCells

this VPL.

ciscoAtmVplCrossIfIndex

For point to point, this is the cross-connected VPL's ifIndex of this VPL. For point to multi-point connection, this will be the root VPL's ifIndex for a leaf VPL entry in the multicast chain, or it's the 1st leaf for a root VPL entry. If it's zero, it me ...

ciscoAtmVplCrossVpi

This specifies the VPI value of the VPL to which this VPL is cross-connected. For point to multi-point connection, this is the root VPL's VPI for the leaf entry. Similarly it is the 1st leaf's VPI value for the root entry.

ciscoAtmVplNextLeafIfIndex

For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VPL's ifIndex on the multicast chain. This will be 0 if this is the root VPL entry. If it's zero for a leaf VPL, it means this is the last leaf ...

ciscoAtmVplNextLeafVpi

For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VPL's VPI on the multicast chain.

ciscoAtmVplRemoteAddr

Soft PVP target address if this is the calling side Soft PVP source address if this is called side. Atomically set ConnState, RemoteAddr and RemoteVpi will create or delete a soft PVP. Atomically set ConnState, RemoteAddr without RemoteVpi will also creat ...

ciscoAtmVplRemoteVpi

Soft PVP target VPI in calling side. 0 in called side.

ciscoAtmVplLocation

Indicate calling or called side of a soft PVP. If ciscoAtmVplConfigType is not soft then ciscoAtmVplLocation value should be ignored.

ciscoAtmVplSlowRetryIntv

Soft PVP slow retry interval time in seconds.

ciscoAtmVplNumAttempts

Number of retries made to install this soft PVP connection. If ciscoAtmVplConfigType is not soft then ciscoAtmVplNumAttempts value should be ignored.

ciscoAtmVplLastReleaseCause

Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVP. Indicates the reason for the Release. ciscoAtmVplConfigType is not soft then ciscoAtmVplLastReleaseCause value should be ignored.

ciscoAtmVplLogicalPortDef

Indicates whether the VPC at this VPL interface is an Atm Logical Port interface.

ciscoAtmVplLogicalPortIndex

The ifTable index of the Atm logical port interface associated with this VPL. Only valid if the value of atmVplLogicalPortDef is isLogicalIf, and the VPL row is active.

ciscoAtmVplUpcViolations

The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VPL. On LS1010 systems, this counter is valid only if equipped with the Feature Card - Per Flow Queueing.

ciscoAtmVplEpdTpdCellDrops

Never implemented.

ciscoAtmVplEpdTpdPacketDrops

Never implemented.

ciscoAtmVplEpdTpdPacketsIn

Never implemented.

ciscoAtmVplClp1Drops

Never implemented.

ciscoAtmVplDefaultRxUpcTolerance

If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified in VPL creation, this object contains the default that is used. If tolerance is explicitly spec ...

ciscoAtmVplDefaultRxUpcVbrCdvt

If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VPL creation, this object contains the default that is used. If CDVT is explicitly specified in VPL creation, it can be ...

ciscoAtmVplLsPerVcqWrrWeight

Configure the weighting specified for a VP half-leg within a service class to make the scheduling decision among other active VPLs in the service class. This is for transmit on the VPL on the interface. This parameter only applies to transit VPs. This obj ...

ciscoAtmVplLsPerVcqTunnelIsShaped

Determines whether this is to be a -shaped- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a shaped VP Tunnel. Such a VP cannot be cross-connected. This object is defined only when the switch is equipped w ...

ciscoAtmVplLsPerVcqXmtQueuedCells

Number of cells received on this VPL and residing on the per-connection queue. Note that this value is not valid until the VPL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chip ...

ciscoAtmVplLsPerVcQThreshGrp

The Threshold Group to which the cell-queue for cells received by this VP are queued. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.

ciscoAtmVplInClp0Cells

The total number of cells with the CLP bit clear received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature ...

ciscoAtmVplInClp1Cells

The total number of cells with the CLP bit set received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature C ...

ciscoAtmVplOutClp0Cells

The total number of cells with the CLP bit clear transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.

ciscoAtmVplOutClp1Cells

The total number of cells with the CLP bit set transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.

ciscoAtmVplCellDrops

The total number of cells received on this VPL, but discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.

ciscoAtmVplClp0VcqFullCellDrops

The total number of cells received on this VPL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Featur ...

ciscoAtmVplVcqClpThreshCellDrops

The total number of cells received on this VPL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and the CLP bit is set. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). ...

ciscoAtmVplLsPerVcqTunnelIsHierarchical

Determines whether this is to be a -Hierarchical- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a Hierarchical VP Tunnel. Such a VP cannot be cross-connected. This object is defined on a LS1010 only when ...

ciscoAtmVplRxNegTraffDescrIndex

Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VPL. This object is not instantiated if this VPL is not the calling side of a soft VP, or if there was no traffic n ...

ciscoAtmVplTxNegTraffDescrIndex

Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VPL. This object is not instantiated if this VPL is not the calling side of a soft VP, or if there was no traffic ...

ciscoAtmVplSwFabOutCells

this VPL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.

ciscoAtmVplSwFabOutClp0Cells

The total number of cells with the CLP bit clear transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical interface (VP Tunnel). This object is not instantiated on systems that do not have support for col ...

ciscoAtmVplSwFabOutClp1Cells

The total number of cells with the CLP bit set transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical interface (VP Tunnel). This object is not instantiated on systems that do not have support for collec ...

ciscoAtmVplConnName

A human readable string that identifies this connection. This object will return a zero-length string if value is not set.

ciscoAtmVplConnType

This object represent the PVP Type for this connection. - local connection within the node - endToEnd across several nodes This object serves as an information object for a management system and has no functional meaning to the switch.

ciscoAtmVclTable

The Virtual Channel Link extension Table.

ciscoAtmVclEntry

An entry in the Vcl table.This entry is used to model a bi-directional Vcl. This table augments the atmVclTable defined in RFC 1695. However it uses ifIndex, atmVclVpi and atmVclVci as an Index for historical reasons. The entries are created/deleted as a ...

ciscoAtmVclCastType

Vcl type is either a point to point connection or point to multipoint root or leaf.

ciscoAtmVclSpanType

Vcl span is either a transit one or a terminating one.

ciscoAtmVclConfigType

Vcl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only.

ciscoAtmVclRxUpcMode

Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection.

ciscoAtmVclEpdEnable

Early Packet Discard option used for this VCL. The use is as follows: enable(1) Packet-discard is enabled. disable(2) Packet-discard is disabled. useTrafficDescr(3) Packet-discard in the receive direction is as specified by the atmTrafficFrameDiscard valu ...

ciscoAtmVclConnState

The connection state of this VCL.

ciscoAtmVclOamLoopbkTxInterval

Frequency of OAM loopback cell are generated on this virtual channel.

ciscoAtmVclOamSegmentLoopback

Enable segment loopback on this virtual channel.

ciscoAtmVclOamEndLoopback

Enable end to end loopback on this virtual channel.

ciscoAtmVclOamAisEnable

Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual channel.

ciscoAtmVclOamRdiEnable

Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received.

ciscoAtmVclInstallTime

The time stamp derived from sysUpTime when this VCL gets created. The VCL entries are created/deleted as a by-product of creating and deleting entries in the atmVclTable defined in RFC1695.

ciscoAtmVclInCells

this VCL.

ciscoAtmVclOutCells

this VCL.

ciscoAtmVclCrossIfIndex

For point to point, this is the cross-connected VCL's ifIndex of this VCL. For point to multi-point connection, this will be the root VCL's ifIndex for a leaf VCL entry in the multicast chain, or it's the 1st leaf VCL for a root VCL entry. If it's zero, i ...

ciscoAtmVclCrossVpi

This specifies the VPI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VPI for the leaf entry. Similarly it is the 1st leaf's VPI value for the root entry.

ciscoAtmVclCrossVci

This specifies the VCI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VCI for the leaf entry. Similarly it is the 1st leaf's VCI value for the root entry.

ciscoAtmVclNextLeafIfIndex

For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VCL's ifIndex on the multicast chain. This will be 0 if this is the root VCL entry. If it's zero for a leaf VCL, it means this is the last leaf ...

ciscoAtmVclNextLeafVpi

For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VPI on the multicast chain.

ciscoAtmVclNextLeafVci

For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VCI on the multicast chain.

ciscoAtmVclAalEncapFlag

Encapsulation type for terminating VC.

ciscoAtmVclAalEncapProtocol

Protocol for terminating VC if EncapFlag is aal5Mux.

ciscoAtmVclAalUserVcType

Following is the list of user virtual circuit types in case aal5Lane encapusation on this virtual channel. boxConfigure -- The shared Server/Client end of a Configure VCC busForward -- The BUS end of the Data Forward VCC busSend -- The BUS end of the Data ...

ciscoAtmVclAtmInArpInterval

Time interval in minutes to send InArp on a PVC for IP over ATM. 0 will disable the InArp for this pvc.

ciscoAtmVclRemoteAddr

Soft PVC target address if this is the calling side Soft PVC source address if this is called side. Atomically set ConnState, RemoteAddr, RemoteVpi and RemoteVci will create or delete a soft PVC. Atomically set ConnState, RemoteAddr without RemoteVpi, Rem ...

ciscoAtmVclRemoteVpi

Soft PVC target VPI in calling side. 0 in called side.

ciscoAtmVclRemoteVci

Soft PVC target VCI in calling side. 0 in called side.

ciscoAtmVclLocation

Indicate calling or called side of a soft PVC. If ciscoAtmVclConfigType is not soft then ciscoAtmVclLocation value should be ignored.

ciscoAtmVclSlowRetryIntv

Soft PVC slow retry interval in seconds.

ciscoAtmVclNumAttempts

Number of retries made to install this soft PVC connection. If ciscoAtmVclConfigType is not soft then ciscoAtmVclNumAttempts value should be ignored.

ciscoAtmVclLastReleaseCause

Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVC. Indicates the reason for the Release. ciscoAtmVclConfigType is not soft then ciscoAtmVclLastReleaseCause value should be ignored.

ciscoAtmVclUpcViolations

The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VCL. On LS1010 systems, this counter is valid only on those equipped with the Feature Card - Per Flow Queueing.

ciscoAtmVclEpdTpdCellDrops

Never implemented.

ciscoAtmVclEpdTpdPacketDrops

The total number of EPD/TPD packet drops of packets received on this VCL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.

ciscoAtmVclEpdTpdPacketsIn

The total number of packets received in their entirety on this VPL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.

ciscoAtmVclClp1Drops

Never implemented.

ciscoAtmVclDefaultRxUpcTolerance

If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified in VCL creation, this object contains the default that is used.If tolerance is explicitly specif ...

ciscoAtmVclDefaultRxUpcVbrCdvt

If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VCL creation, this object contains the default that is used. If CDVT is explicitly specified in VCL creation, it can be ...

ciscoAtmVclLsPerVcqWrrWeight

Configure the weighting specified for a VC half-leg within a service class to make the scheduling decision among other active VCLs in the service class. This is for transmit on the VCL on the interface. This object is defined only when the switch is equip ...

ciscoAtmVclLsPerVcqXmtQueuedCells

Number of cells received on this VCL and residing on the per-connection queue. Note that this value is not valid until the VCL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chip ...

ciscoAtmVclLsPerVcQThreshGrp

The Threshold Group to which the cell-queue for cells received by this VC are queued. Note that this value is not valid until the VCL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queuei ...

ciscoAtmVclInClp0Cells

The total number of cells with the CLP bit clear received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.

ciscoAtmVclInClp1Cells

The total number of cells with the CLP bit set received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.

ciscoAtmVclOutClp0Cells

The total number of cells with the CLP bit clear transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.

ciscoAtmVclOutClp1Cells

The total number of cells with the CLP bit set transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.

ciscoAtmVclCellDrops

The total number of cells received on this VCL, but discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.

ciscoAtmVclClp0VcqFullCellDrops

The total number of cells received on this VCL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if EPD is disabled on the VCL. - on LS1010 systems, only those equipped with Feature Card - Per Flow ...

ciscoAtmVclVcqClpThreshCellDrops

The total number of cells received on this VCL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and the CLP bit is set. This counter is valid only: - if EPD is disabled on the VCL. - on LS1010 syste ...

ciscoAtmVclRxNegTraffDescrIndex

Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VCL. This object is not instantiated if this VCL is not the calling side of a soft VC, or if there was no traffic n ...

ciscoAtmVclTxNegTraffDescrIndex

Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VCL. This object is not instantiated if this VCL is not the calling side of a soft VC, or if there was no traffic ...

ciscoAtmVclSwFabOutCells

this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.

ciscoAtmVclSwFabOutClp0Cells

The total number of cells with the CLP bit clear transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.

ciscoAtmVclSwFabOutClp1Cells

The total number of cells with the CLP bit set transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.

ciscoAtmVclConnName

A human readable string that identifies this connection. This object will return a zero-length string if value is not set.

ciscoAtmVclConnType

This object represent the PVC Type for this connection. - local connection within the node - endToEnd across several nodes. This object serves as an information object for a management system and has no functional meaning to the switch.

ciscoAtmSvpAddrTable

Switched virtual path link address table.

ciscoAtmSvpAddrEntry

An entry in the Switched Vrtual Path address table.

ciscoAtmSvpAddr

It depends on the direction.This could be p2pCallingSide address on a called side VPL, or p2pCalledSide address on a calling side VPL or p2mpRoot address on a p2mp leaf side VPL or p2mpLeaf address on a p2mp root side VPL.

ciscoAtmSvpVpi

This SVP's VPI value on this interface.

ciscoAtmSvpDirection

Indicate whether this VPL is calling side, called side, root or leaf for this address.

ciscoAtmSvcAddrTable

Switched virtual channel link address table.

ciscoAtmSvcAddrEntry

An entry in the SVC address table.

ciscoAtmSvcAddr

It depends on the direction.This could be p2pCallingSide address on a called side VCL, or p2pCalledSide address on a calling side VCL or p2mpRoot address on a p2mp leaf side VCL or p2mpLeaf address on a p2mp root side VCL.

ciscoAtmSvcVpi

This SVC's VPI value on this interface.

ciscoAtmSvcVci

This SVC's VCI value on this interface.

ciscoAtmSvcDirection

Indicate whether this VCL is calling side, called side, root or leaf for this address.

ciscoAtmSnoopVcTable

Snooping VC Table.

ciscoAtmSnoopVcEntry

An entry in the Snoop VC table. This entry models a VC snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi and atmVclVci specifies the VPI and VCI value of the snooping connection. To create or destroy a snooping connection ...

ciscoAtmSnoopVcSnoopedIfIndex

This specifies the ifIndex of the snooped interface.

ciscoAtmSnoopVcSnoopedVpi

This specifies the VPI value of the snooped connection endpoint.

ciscoAtmSnoopVcSnoopedVci

This specifies the VCI value of the snooped connection endpoint.

ciscoAtmSnoopVcDir

This specifies the traffic direction at the snooped connection endpoint.

ciscoAtmSnoopVcState

The connection state of this Snooping connetion.

ciscoAtmSnoopVcRowStatus

This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vc snooping connection

ciscoAtmSnoopVpTable

Snooping VP Table.

ciscoAtmSnoopVpEntry

An entry in the Snoop VP table. This entry models a VP snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi specifies the VPI value of the snooping connection. To create or destroy a snooping connection at an ATM interface, t ...

ciscoAtmSnoopVpSnoopedIfIndex

This specifies the ifIndex of the snooped interface.

ciscoAtmSnoopVpSnoopedVpi

This specifies the VPI value of the snooped connection endpoint.

ciscoAtmSnoopVpDir

This specifies the traffic direction at the snooped connection endpoint.

ciscoAtmSnoopVpState

The connection state of this Snooping connection .

ciscoAtmSnoopVpRowStatus

This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vp snooping connection

ciscoAtmSvcFrameDiscardUsesAal5Ie

Determines mechanism to use on interfaces to specify frame discard. Specifying a value of true causes the presence of the AAL5 IE to influence whether frame discard is used on an SVC. If AAL5 IE is present in a received SETUP, frame discard is used. Speci ...

ciscoAtmConnMIBGroup

ciscoAtmConnMIBGroup2

ciscoAtmConnMIBGroup3

ciscoAtmConnMIBlsPerVcqGroup

A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset.

ciscoAtmConnMIBlsFcPfqGroup

A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card.

ciscoAtmConnMIBlsPerVcqGroup2

A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset.

ciscoAtmConnMIBNegTraffGroup

A collection of objects to report negotiated traffic parameters on a Cisco ATM switch.

ciscoAtmConnMIBlsFcPfqGroup1

A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card.

ciscoAtmConnMIBGroup1

ciscoAtmConnMIBGroup4

ciscoAtmConnNmsGroup

A group of objects that provides additional information for a management system