CISCO-ATM-DUAL-PHY-MIB Download
The MIB module for gathering physical layer error statistics
from the ATM uplink card of a Catalyst 5000 device. It also
allows users to select the "active" phy in the above card in a
redundant phy configuration.
IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for CISCO-ATM-DUAL-PHY-MIB
- cadpStatTable
- A table of status information about ATM phy.
- cadpStatEntry
- An Atm Phy table entry, containing information about a phy on this ATM module.
- cadpStatLossOfSignal
- Set to true if the phy is currently experiencing a loss of signal (LOS) from its connected port. Set to false if the phy is not experiencing a loss of signal.
- cadpStatFarEndReceiveFailure
- Set to true if the phy is currently experiencing a far end receive failure (FERF) with its connected port. Set to false if the phy is not experiencing a far end receive failure.
- cadpStatActive
- Set to true when this phy is currently the active phy. Set to false when this phy is not the currently active phy.
- cadpStatSectionBIP8Errors
- The Bit Interleaved Parity 8 is an error checking code applied for quick isolation of faults. Each bit in the B octets is set to 1 or 0 as necessary to obtain even parity over the previous frame. The calculated BIP-8 code for frame N is compared with th ...
- cadpStatLineBIP824Errors
- The Bit Interleaved Parity 8/24 is an error checking code based on even parity. The calculated BIP code for frame N is compared with the BIP-8/24 code extracted from the B2 byte(s) of frame N+1. Any differences indicate that a line layer bit error has o ...
- cadpStatLineFEBErrors
- The number of bits (binary 000 to 1000) in the previous BIP-8 that didn't match the even parity check are inserted by the transmitter. The receiver checks for this in the M0/M1 byte of the frame. A non-zero value (legal range is binary 0000 - 1000) indi ...
- cadpStatPathBIP8Errors
- The Bit Interleaved Parity 8 is an error checking code applied for quick isolation of faults. Each bit in the B octets is set to 1 or 0 as necessary to obtain even parity over the previous frame. The calculated BIP-8 code for frame N is compared with the ...
- cadpStatPathFEBErrors
- The number of B3 errors in the previous frame inserted by the transmitter. The receiver checks for this in the G1 byte of the frame. A non-zero value (legal range is binary 0000 - 1000) indicates a line layer error in the remote end. Any other value is ...
- cadpStatCorrectableHCSErrors
- The Header Checksum (HCS) is a CRC-8 calculation over the first 4 octets of the ATM cell header. The received HCS is verified using the polynomial x^8 + x^2 + x + 1. The coset polynomial x^6 + x^4 + x^2 + 1, is added (modulo 2) to the received HCS octet ...
- cadpStatUncorrectableHCSErrors
- The Header Checksum (HCS) is a CRC-8 calculation over the first 4 octets of the ATM cell header. The received HCS is verified using the polynomial x^8 + x^2 + x + 1. The coset polynomial x^6 + x^4 + x^2 + 1, is added (modulo 2) to the received HCS octet b ...
- cadpStatOperActivePhy
- Returns the ifIndex of the phy which is currently the active phy. A value of 0 indicates that no phy is currently active.
- cadpStatAdminActivePhy
- Returns the ifIndex of the phy which is the preferred active phy. A value of 0 indicates that no phy is currently active. Setting this object to a value different from its current value causes the ATM module to make the indicated phy active, and the acti ...
- ciscoAtmDualPhyMIBGroup
- A collection of objects providing ATM dual phy monitoring.
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
