CISCO-DSP-MGMT-MIB Download

cdspCardStatusTable

The DSP Card Table. It contains status information of the DSP cards present within the router.

cdspCardStatusEntry

An entry in the DSP card table indicates the DSP card state, resource utilization. Each entry is created when a DSP software is detected on a DSP card. The entry is deleted when the DSP card is deleted.

cdspCardIndex

The object corresponds to cardIndex in the chassis mib. If value of this object is 0, then the entry is not associated to cardIndex of the chassis mib.

cdspCardState

The object indicates the current state of DSP card being monitored. normal - DSP card in normal condition. warning - DSP card has some problem and need attention. critical - DSP card has a major alarm. fatal - DSP card is not functional. DSP subsyst ...

cdspCardResourceUtilization

The object indicates the percentage of current DSP resource utilization of the card. The utilization is a ratio of number of busy DSP resources (for handling calls, transcoding, voice compression,...) to the total available DSP resources.

cdspCardLastHiWaterUtilization

The object indicates the last high water mark of DSP resource utilization. This object is reset to 0 after DSP card is reset.

cdspCardLastResetTime

The value of sysUpTime when the last DSP card reset occurred.

cdspCardMaxChanPerDSP

The maximum number of channels allowed in each DSP. The value is chosen in an implementation-dependent manner by the DSP functionality. The value of 0 in this object indicates Channelized DSP mode is turned off.

cdspTotalDsp

The total number of DSPs in the card.

cdspFailedDsp

The number of DSPs in the failed state (i.e cdspOperstate is 'failed')

cdspDspSwitchOverThreshold

This object specifies the threshold of DSP failures. When 'cdspFailedDsp' reaches the value of this object, the voice gateway switchover will occur. The maximum value of this object can not be more than the value in 'cdspTotalDsp'

cdspCongestedDsp

The number of DSPs in the congested state (i.e cdspOperstate is 'congested').

cdspNormalDsp

The number of DSPs in the normal state (i.e cdspOperstate is 'normal').

cdspNx64Dsp

This object specifies the number of DSPs that need to be set aside for making Nx64 calls. The max value of this object is limited to the value of the object 'cdspTotalDsp'. If this value is 0, it is not allowed to make any Nx64 call. The default value of ...

cdspCodecTemplateSupported

This object indicates the codec template supported in DSP image. The codec template can be: tgw - Codec template for wireline used in Trunking GateWay application. cable - Codec template for AES (Advanced Encryption Standard) encryption used in cable ...

cdspCardVideoPoolUtilization

The object indicates the percentage of current DSP video resource pool utilization of the card.

cdspCardVideoPoolUtilizationThreshold

This object specifies the threshold of DSP video pool resource usage. When cdspCardVideoPoolUtilization crosses the value of this threshold in the rising direction, cdspVideoUsageNotification is generated. If cdspCardVideoPoolUtilization stays above the v ...

cdspStatusTable

Status information for the DSPs. This status table is used for tracking dangling DSP resources. The dangling DSP channel means that the DSP channel is reserved for serving calls but the channel is not used by active calls. The number of the dangling DSP c ...

cdspStatusEntry

An entry in cdspStatusTable indicates the DSP state and alarm conditions. Each entry is created when a DSP is detected on a DSP card. The entry is deleted when the DSP card is deleted. The 'entPhysicalIndex' represents a DSP entity, and the 'entPhysicalCl ...

cdspOperState

The current operational state of the DSP. normal - DSP operates normally shutdown - DSP is shutdown due to fatal error congested - DSP does not accept call because the DSP buffer is full failed - DSP failed

cdspAlarms

The object indicates the accumulated number of DSP Alarms.

cdspLastAlarmCause

The object indicates the current or last alarm state of DSP. other - none of the following noAlarm - alarm condition had not been detected dspFatalError - DSP fatal error dspMemoryError - DSP memory error is detected dspBufferErro ...

cdspLastAlarmCauseText

The object indicates the failure reason for the current or last DSP Alarm. It should be used only for direct, human-readable display and only if a management station is unable to decode the value of cdspLastAlarmCause.

cdspLastAlarmTime

The value of sysUpTime when the last DSP Alarm occurred. The value of this object is 0 if the value of cdspLastAlarmCause object is 'noAlarm'.

cdspTotalChannels

The total number of channels in the DSP. This value is predetermined by the DSP functionality upon initialization. The value of 0 in this object indicates Channelized DSP mode is turned off.

cdspInUseChannels

The number of channels that are reserved for serving calls. The value is incremented when the DSP channel is reserved for call setup and is decremented after the DSP channel is free due to call disconnection.

cdspActiveChannels

The number of channels that are used by active calls to process media stream. The value is incremented after the reserved DSP channel enters call connection state and is decremented after the call is disconnected.

cdspSigBearerChannelSplit

This object indicates if the DSP channels are splitted for signaling call and bearer call. If the value of this object is 'true' which means that signaling call and bearer call cannot share any DSP channel. This object is not applicable when Channelized D ...

cdspNumCongestionOccurrence

The number of congestion occurred on the DSP. This value is set to 0 when system is reset.

cdspDspNum

This object identifies the DSP number associated with this DSP entity.

cdspStatusXTable

This table provides the additional detailed state and statistics information for a DSP that supports the splitted signalling and bearer channels.

cdspStatusXEntry

An entry of this table is created when its associated entry in cdspStatusTable is created and the value of cdspSigBearerChannelSplit object is 'true'.

cdspXNumberOfBearerCalls

The current number of bearer calls on the DSP.

cdspXNumberOfSigCalls

The current number of signaling calls on the DSP.

cdspXAvailableBearerBandwidth

The percentage of channels on the DSP currently available for bearer calls.

cdspXAvailableSigBandwidth

The percentage of channels on the DSP currently available for signaling calls.

cdspVoiceParamTable

This table contains information on voice call setup related parameters for DSP resource.

cdspVoiceParamEntry

An entry in the DSP table contains information regarding a single DSP resource associated voice call setup parameters. An entry in this table is created when a DSP is detected and the DSP resource can be used by voice applications. An entry in this table ...

cdspRtpSidPayloadType

This object specifies the RTP (Real Time Protocol) payload type of the SID (Silence Insertion Descriptor) packet that is sent to the remote endpoint at the onset of silence suppression.

cdspRtcpControl

This objects controls if RTCP (Real Time Control Protocol) will be enabled. If this object is set to 'true', both transmission and reception of RTCP packets are enabled; otherwise, transmission of RTCP packets is disabled while any received RTCP packets a ...

cdspRtcpTransInterval

This attribute specifies the RTCP report interval (defined in RFC1889). It indicates the interval in which the RTCP reports should be sent to the participating members. RTCP reports is sent out in a random interval computed by using 'cdspRtcpTransInterval ...

cdspRtcpRecvMultiplier

This object specifies an approximate RTCP report interval (defined in RFC 1889) in milliseconds in which the RTCP reports should be sent to the participating members. It specifies how many times the RTCP reports may fail before exception condition activit ...

cdspVadAdaptive

This attribute is used to enable or disable the Adaptive VAD knob of the VAD algorithm. Adaptive VAD works in conjunction with VAD Threshold (cvifcfgMusicOnHoldThreshold from CISCO-VOICE-IF-MIB). When this object set to 'true', VAD Threshold is ignored an ...

cdspDtmfPowerLevel

This object specifies the power level of the low frequency component of DTMF. The power level of the high frequency component of DTMF is relative above or below the value specified in object cdspDtmfPowerTwist. If the value of cdspDtmfPowerTwist is 0, the ...

cdspDtmfPowerTwist

This object specifies the relative power level of the high frequency component of DTMF. The low frequency group is always fixed to the value specified by cdspDtmfPowerLevel. When this object is set to 0, the power level of both frequency components is set ...

cdspRtcpTimerControl

This object specifies when the RTCP receive timer is started. disabled - timer is disabled startImmediately - timer starts immediately as soon as RTCP is enabled on the call startRtpOrRtcpPktRcvd - timer starts upon reception of the firs ...

cdspVqmControl

This object is used to disable VQM or enable either RFC 3611 RTCPXR or Extended Network Quality Metrics VQM. disable - VQM is disabled. rfc3611Vqm - RFC 3611 RTCPXR. RTCPXR packet uses extended report block type as defined in RFC3611. xnq - Extended Netw ...

cdspRtcpXrControl

This object controls if RTCPXR (Real Time Control Protocol Extended Report) is enabled. If this object is set to 'true', both transmission and reception of RTCPXR packets are enabled; otherwise, transmission of RTCPXR packets is disabled while any receive ...

cdspRtcpXrTransMultiplier

This object is used to configure the RTCPXR report frequency. i.e. how many RTCP packets during the interval of every RTCPXR packet. The RTCPXR report is sent every 'cdspRtcpXrTransMultiplier' of RTCP packet. Example: If RTCP packet is sent every 10 ms(fr ...

cdspRtcpXrGminDefault

This object is the default minimum gap value configured for the IP stream. This object is applicable only if 'cdspVqmControl' is set to 'rfc3611Vqm'.

cdspRtcpXrExtRfactor

This object is the external R factor metric value. The value 127 means it is not applicable. This object is applicable only if 'cdspVqmControl' is set to 'rfc3611Vqm'. When 'cdspVqmControl' is not 'rfc3611Vqm', this object is set to 127.

cdspPktLossConcealment

This object specifies the packet loss concealment: (1) none: No packet loss concealment applied (2) simple: Cisco Proprietary packet loss concealment (3) g711A1: ITU G.711 Appendix I compliant

cdspVqmThreshSES

This attribute specifies the threshold for Severely Errored Second on VQM. If the total number of milliseconds sampled as bad voice quality in one second period exceeds threshold, then this second is considered a 'severely errored second'. This object is ...

cdspTransparentIpIp

This attribute is used to enable or disable the transparent mode when establishing a non-transcoding IP-IP connection. The attribute does not apply for the transcoding IP-IP connections. A non-transcoding connection is one where the codec and packetizatio ...

cdspVoiceModeIpIp

This object specifies the voice mode for IP IP connections. normal : A normal Mode is a transcoding mode for IP-IP connections where the bearer properties will be different on two ends of a call. fastRoute : A voice call will be esatblished in this mo ...

cdspUtilTable

This table contains DSP utilization information for all the codec families available in codec template currently active on VXSM.

cdspUtilEntry

An entry (conceptual row) in cdspUtilTable indicates the DSP capacity usage. Each entry maps to a codec pool family , uniquely identified by cdspCodecPoolIndex, and displays corresponding utilized and available DSP channels. The entry is derived based on ...

cdspCodecPoolIndex

This object identifies a row. Pool index is corresponding to the number of DSP channels utilized. The instance identifier value of this object depends on the codec template supported on this module as indicated by the value of corresponding instance of 'c ...

cdspCurrentUtilCap

This object indicates the number of DSP channels which are currently being utilized corresponding to active calls on VXSM segregated on the basis of codec families.

cdspCurrentAvlbCap

This object indicates the number of DSP channels which are currently available on VXSM corresponding to a codec family.

cdspGlobMaxConfTranscodeSess

This object indicates the maximum transcode sessions configured globally for the voice gateway.

cdspGlobMaxAvailTranscodeSess

This object indicates the total number of available sessions from the maximum transcode sessions configured globally for the voice gateway.

cdspTranscodeProfileTable

This table contains information about each transcode DSPFarm profile. It gives the maximum number of transcode sessions configured and the number of available sessions per profile.

cdspTranscodeProfileEntry

An entry in cdspTranscodeProfileTable indicates the transcode DSPFarm profile maximum configured sessions and available sessions. Each DSPFarm transcode profile configured in the voice gateway forms a new entry to this table. The entry is deleted when the ...

cdspTranscodeProfileId

This object indicates the profile number of the DSPFarm transcode profile.

cdspTranscodeProfileMaxConfSess

This object indicates the maximum transcode sessions configured on the DSPFarm transcode profile for the voice gateway.

cdspTranscodeProfileMaxAvailSess

This object indicates the total number of available transcode sessions per transcode profile from the configured maximum transcode sessions per transcode profile for the voice gateway.

cdspTranscodeProfileRowStatus

This object is used to create a new entry or delete an existing entry in cdspTranscodeProfileTable. The storage type for all the entries created would be volatile. To retain the configured entries. One must write the configuration to memory in the voice g ...

cdspMtpProfileTable

This table contains information about each MTP DSPFarm profile. It gives the maximum number of MTP sessions configured and the number of available sessions per profile.

cdspMtpProfileEntry

An entry in cdspMtpProfileTable indicates the MTP DSPFarm profile maximum configured sessions and available sessions. Each DSPFarm MTP profile configured in the voice gateway forms a new entry to this table. The entry is deleted when the MTP DSPFarm profi ...

cdspMtpProfileId

This object indicates the profile number of the DSPFarm MTP profile.

cdspMtpProfileMaxConfSoftSess

This object indicates the maximum MTP software sessions configured per DSPFarm MTP profile for the voice gateway.

cdspMtpProfileMaxConfHardSess

This object indicates the maximum MTP hardware sessions configured per DSPFarm MTP profile for the voice gateway.

cdspMtpProfileMaxAvailHardSess

This object indicates the total number of available MTP sessions per MTP profile from the configured maximum MTP sessions per MTP profile for the voice gateway.

cdspMtpProfileRowStatus

This object is used to create a new entry or delete an existing entry in cdspMtpProfileTable. The storage type for all the entries created would be volatile. To retain the configured entries. One must write the configuration to memory in the voice gateway ...

cdspTotAvailTranscodeSess

This object indicates the total number of transcode sessions available for the voice gateway. The value is equal to summation of all the values returned by transcode profile object cdspTranscodeProfileMaxAvailSess.

cdspTotUnusedTranscodeSess

This object indicates the total number of unused transcode sessions.

cdspTotAvailMtpSess

This object indicates the total number of MTP sessions available for the voice gateway. The value is equal to summation of all the values returned by MTP profile object cdspMtpProfileMaxAvailHardSess.

cdspTotUnusedMtpSess

This object indicates the total number of unused MTP sessions.

cdspMIBEnableCardStatusNotification

This variable controls whether the system produces the cdspMIBCardStateNotification. A false value will prevent DSP card fatal notifications from being generated by this system.

cdspEnableOperStateNotification

This variable controls whether the system produces the cdspOperStateNotification. A false value will prevent a DSP operational state notification from being generated by this system.

cdspVideoUsageNotificationEnable

This object specifies whether the system produces cdspVideoUsageNotification. 'true': Video usage notification is generated by this system. 'false': Video usage notification is not generated by this system.

cdspVideoOutOfResourceNotificationEnable

This object specifies whether the system produces cdspVideoOutOfResourceNotification. 'true': Video out-of-resource notification is generated by this system. 'false': Video out-of-resource notification is not generated by this system.

cdspMgmtGeneralInfoGroup

A collection of objects providing the Digital Signal Processing related information.

cdspChannelGroup

A collection of objects providing information specific for multiple channels per DSP.

cdspMgmtExtGeneralInfoGroup

A collection of objects providing information for DSP.

cdspVoiceInfoGroup

A collection of objects providing DSP voice application parameters.

cdspChannelExtGroup

A collection of objects providing DSP channels splitting information.

cdspVoiceInfoGroupRev1

A collection of objects providing DSP voice application parameters.

cdspMgmtExtGeneralInfoGroupRev1

This group replaces cdspMgmtExtGeneralInfoGroup. A collection of objects providing information for DSP.

cdspMgmtGeneralInfoGroupRev1

A collection of objects providing the Digital Signal Processing related information.

cdspVQMGroup

This group includs VQM (Voice Quality Monitor) related information. It is mandatory only if VQM is supported.

cdspVoiceInfoGroupRev2

A collection of objects providing DSP voice application parameters.

cdspTransCodingGroup

A collection of objects providing DSP transcoding related parameters.

cdspTransCodingGroup1

A collection of objects providing DSP transcoding related parameters for voice.

cdspUtilInfoGroup

A collection of objects providing DSP codec capacity usage .

cdspDspfarmInfoGroup

A collection of objects providing DSPFarm session configuration, availability and utilization.

cdspMgmtVideoInfoGroup

A collection of objects related to DSP video resource.