CISCO-FCOE-MIB Download

cfcoeCfgTable

This table facilitates configuration of FCoE parameters on a per Fibre Channel management instance.

cfcoeCfgEntry

There is one entry in this table for each Fibre Channel management instance.

cfcoeCfgFcmap

This object configures the FC-MAP value used by the FCF when operating in FPMA mode. The default value is 0EFC00h, as written in the standard.

cfcoeCfgDynamicVfcCreation

This object allows the user to enable (TRUE) or disable (FALSE) dynamic VFC interface creation on the FCF. When set to TRUE VFC interfaces are dynamically created when a FIP based FLOGI or ELP request is received.

cfcoeCfgDynamicVfcAgeTimer

This ageing timer (in seconds) is used by the FCF to age out dynamically created VFC interfaces. The default value is 300 seconds.

cfcoeCfgDefaultFCFPriority

The FIP priority value advertised by the FCF to ENodes by default. cfcoeStaticVfcFCFPriority configured for a VFC interface overrides this setting for the ENode associated with the VFC.

cfcoeCfgDATov

The Discovery_Advertisement_Timeout value configured for the FCF. This is used as the timeout value in seconds by the FCF to send periodic Discovery Advertisements.

cfcoeCfgAddressingMode

Addressing mode(s) supported by the FCF. Implementations should fail set requests for unsupported modes.

cfcoeVLANTable

This table facilitates configuration of VLAN and Fabric (VSAN) associations in an FCoE network. FCoE forwarding for a fabric is over a VLAN in a L2 Ethernet network. That is, reachability between the ENode/remote-FCF and an FCF for a given fabric is dete ...

cfcoeVLANEntry

There is one entry in this table for each VLAN that is designated to transport FCoE traffic for a given fabric (VSAN).

cfcoeVLANIndex

This object identifies the VLAN ID that FCoE FCF function is being enabled for.

cfcoeFabricIndex

This object identifies the Fabric Index of the VSAN traffic for which can be transported over the VLAN identified by cfcoeVLANIndex.

cfcoeVLANOperState

Operational state of this VLAN-VSAN association entry. The 'up' state is achieved when both the VSAN and VLAN are valid.

cfcoeVLANRowStatus

The status of this conceptual row. The RowStatus becomes active on successful creation of an entry.

cfcoeStaticVfcTable

This table facilitates the creation and deletion of static VFC interfaces. While VFCs can be dynamically created based on FIP FLOGI/ELP requests users may want to associate certain pre-configured policy for a particular ENode or a remote-FCF. In such case ...

cfcoeStaticVfcEntry

There is one entry in this table for each statically created VFC Interface.

cfcoeStaticVfcIndex

This index uniquely identifies a static VFC entry in this table.

cfcoeStaticVfcFCFPriority

If this VFC is for a VF_Port this object is used to configure FCF priority to be advertised to the ENode associated with the VFC.

cfcoeStaticVfcBindType

The mechanism to identify the ENode associated with this VFC if it is of type VF_Port or to identify the remote-FCF associated with this VFC if it is of type VE_Port.

cfcoeStaticVfcBindIfIndex

This object allows for configuration of ifIndex of the ethernet interface over which the FCF reaches the ENode or the remote-FCF that this VFC identifies. This object is to be used only when the ENode or the remote-FCF is directly connected to the FCF ove ...

cfcoeStaticVfcBindMACAddress

This object allows the user to configure MAC address of the ENode or the remote-FCF that this VFC interface identifies. An ENode or remote-FCF is associated to this VFC only if the source MAC address in the FIP frames matches with this object.

cfcoeStaticVfcIfIndex

The ifIndex of this virtual FC interface.

cfcoeStaticVfcCreationTime

The timestamp of this entry's creation time.

cfcoeStaticVfcFailureCause

The cause of failure for the last bind operation. This object will be zero length if and only if the bind is successful.

cfcoeStaticVfcRowStatus

The status of this conceptual row. The RowStatus becomes active on successful creation of a virtual interface. The VFC must be bound before it can become operational.

cfcoeFipSnoopingEnable

This object is used to enable or disable FIP Snooping on an Ethernet Bridge.

cfcoeFipSnoopingFcmap

This object configures the FC-MAP value associated with the FIP snooping Ethernet bridge.

cfcoeEnodeIntfTable

The (conceptual) table containing the interfaces on an Ethernet bridge that are directly connected to ENodes. A FIP Snooping bridge will automatically configure ACLs on these interfaces based on FIP login requests and responses.

cfcoeEnodeIntfEntry

An entry (conceptual row) in the cfcoeEnodeIntfTable, representing an interface directly connected to an ENode on the Ethernet Bridge.

cfcoeEnodeIntfIfIndex

The ifIndex of the interface on the Ethernet bridge connected to an Enode.

cfcoeEnodeIntfRowStatus

The status of this conceptual row.

cfcoeCfgConformanceObjects

A collection of objects related to all implementations of FCoE.

cfcoeVLANConformanceObjects

A collection of objects related to implementation of FCoE VLANs.

cfcoeStaticVfcConformanceObjects

A collection of objects related to implementation of static VFC interfaces.

cfcoeFipSnoopingConformanceObjects

A collection of objects related to implementation of FIP Snooping.

cfcoeEnodeIntfObjects

A collection of objects related to implementation of ENode interfaces on a FIP snooping bridge.