CISCO-IEEE-CFM-MIB Download

Connectivity Fault Management module for managing IEEE 802.1ag

IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for CISCO-IEEE-CFM-MIB

cdot1agStackEntry: The Stack table entry
cdot1agStackifIndex: This object represents the Bridge Port or aggregated port on which MEPs or MHFs might be configured. Upon a restart of the system, the system SHALL, if necessary, change the value of this variable, and rearrange the cdot1agStackTable, so that it indexes ...
cdot1agStackVlanIdOrNone: VLAN ID to which the MP is attached, or 0, if none.
cdot1agStackMdLevel: MD Level of the Maintenance Point.
cdot1agStackDirection: Direction in which the MP faces on the Bridge Port
cdot1agStackMdIndex: The index of the Maintenance Domain in the cdot1agMdTable to which the MP is associated, or 0, if none.
cdot1agStackMaIndex: The index of the MA in the cdot1agMaTable to which the MP is associated, or 0, if none.
cdot1agStackMepId: If an MEP is configured, the MEPID, else 0
cdot1agStackMacAddress: MAC address of the MP.
cdot1agVlanTable: This table defines the association of VIDs into VLANs. There is an entry in this table for each VID that is: a) a VID belonging to a VLAN associated with more than one VID; and b) not the Primary VLAN of that VID. The entry in this table contains the Pri ...
cdot1agVlanEntry: The VLAN table entry.
cdot1agVlanVid: This is a VLAN ID belonging to a VLAN that is associated with more than one VLAN ID, and this is not the Primary VID of the VLAN. ::= { cdot1agVlanEntry 1 } SYNTAX VlanId MAX-ACCESS read-create STATUS current DESCRIPTION This is the Primary VLA ...
cdot1agDefaultMdDefMhfCreation: A value indicating if the Management entity can create MHFs (MIP Half Function) for the VID, for each cdot1agDefaultMdEntry whose cdot1agDefaultMdMhfCreation object contains the value defMHFdefer. Since, in this variable, there is no encompassing Mainten ...
cdot1agDefaultMdDefIdPermission: Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MHFs created by the Default Maintenance Domain, for each cdot1agDefaultMdEntry whose cdot1agDefaultMdIdPermission object contains the value sendI ...
cdot1agDefaultMdTable: The Default MD Level Managed Object controls MHF creation for VIDs that are not attached to a specific Maintenance Association Managed Object, and Sender ID TLV transmission by those MHFs. For each Bridge Port, and for each VLAN ID whose data can pass thr ...
cdot1agDefaultMdEntry: The Default MD Level table entry.
cdot1agDefaultMdPrimaryVid: The Primary VID of the VLAN to which this entry's objects apply
cdot1agDefaultMdStatus: State of this Default MD Level table entry. True if there is no entry in the Maintenance Association table defining an MA for the same VLAN ID and MD Level as this table's entry, and on which MA an Up MEP is defined, else false. REFERENCE 802.1ag clause ...
cdot1agDefaultMdLevel: A value indicating the MD Level at which MHFs are to be created, and Sender ID TLV transmission by those MHFs is to be controlled, for the VLAN to which this entry's objects apply. If this object has the value -1, the MD Level for MHF creation for this V ...
cdot1agDefaultMdMhfCreation: A value indicating if the Management entity can create MHFs (MIP Half Function) for this VID at this MD Level. If this object has the value defMHFdefer, MHF creation for this VLAN is controlled by cdot1agDefaultMdDefMhfCreation. The value of this variabl ...
cdot1agDefaultMdIdPermission: Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MHFs created by the Default Maintenance Domain. If this object has the value sendIdDefer, Sender ID TLV transmission for this VLAN is controlled ...
cdot1agConfigErrorListTable: The CFM Configuration Error List table provides a list of Interfaces and VIDs that are incorrectly configured. REFERENCE 802.1ag clause 12.14.4
cdot1agConfigErrorListEntry: The Config Error List Table entry
cdot1agConfigErrorListVid: The VLAN ID of the VLAN with interfaces in error.
cdot1agConfigErrorListIfIndex: This object is the IfIndex of the interface. Upon a restart of the system, the system SHALL, if necessary, change the value of this variable so that it indexes the entry in the interface table with the same value of ifAlias that it indexed before the syst ...
cdot1agConfigErrorListErrorType: A vector of Boolean error conditions from 22.2.4, any of which may be true: 0) CFMleak; 1) ConflictingVids; 2) ExcessiveLevels; 3) OverlappedLevels. REFERENCE 802.1ag clause 12.14.4.1.3:b
cdot1agMdTableNextIndex: This object contains an unused value for cdot1agMdIndex in the cdot1agMdTable, or a zero to indicate that none exist. ::= { cdot1agMd 1 } -- ****************************************************************** -- The Maintenance Domain Table -- ************ ...
cdot1agMdEntry: The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage. INDEX {cdot1agMdIndex } ::= { cdot1agMdTable 1 } Cdot1agMdEntry ::= SEQUENCE { cdot1agMdIndex Unsigned32, cdot1agMdFormat ...
cdot1agMdName: The Maintenance Domain name. The type/format of this object is determined by the value of the cdot1agMdNameType object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy ide ...
cdot1agMdMdLevel: The Maintenance Domain Level.
cdot1agMdMhfCreation: Enumerated value indicating whether the management entity can create MHFs (MIP Half Function) for this Maintenance Domain. REFERENCE 802.1ag clause 12.14.5.1.3:c
cdot1agMdMhfIdPermission: Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MPs configured in this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value sendIdDefer takes the ...
cdot1agMdMaTableNextIndex: Value to be used as the index of the MA table entries for this Maintenance Domain when the management entity wants to create a new row in the MA table. ::= { cdot1agMdEntry 7 } SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION ...
cdot1agMaEntry: The MA table entry.
cdot1agMaIndex: Index of the MA table cdot1agMdMaTableNextIndex needs to be inspected to find an available index for row-creation. ::= { cdot1agMaEntry 1 } SYNTAX VlanId MAX-ACCESS read-create STATUS current DESCRIPTION The Primary VLAN ID with which the Maint ...
cdot1agMaFormat: The type (and thereby format) of the Maintenance Association Name. REFERENCE 802.1ag clauses 21.6.5.4
cdot1agMaName: The Short Maintenance Association name. The type/format of this object is determined by the value of the cdot1agMaNameType object. REFERENCE 802.1ag clauses 21.6.5.6, and Table 21-20
cdot1agMaMhfCreation: Indicates if the Management entity can create MHFs (MIP Half Function) for this MA. REFERENCE 802.1ag clause 12.14.6.1.3:c
cdot1agMaIdPermission: Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MPs configured in this MA. REFERENCE 802.1ag clause 12.14.6.1.3:d
cdot1agMaCcmInterval: Interval between CCM transmissions to be used by all MEPs in the MA. REFERENCE 802.1ag clause 12.14.6.1.3:e
cdot1agMaNumberOfVids: The number of VIDs associated with the MA. REFERENCE 802.1ag clause 12.14.6.1.3:b
cdot1agMaRowStatus: The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated. ::= { cdot1agMaEntry 9 } -- ****************************************************************** ...
cdot1agMaMepListEntry: The known MEPS table entry.
cdot1agMaMepListIdentifier: MEPID
cdot1agMaMepListRowStatus: The status of the row. Read SNMPv2-TC (RFC1903) for an explanation of the possible values this object can take. ::= { cdot1agMaMepListEntry 2 } -- ****************************************************************** -- The MEP Object. This object represent ...
cdot1agMepEntry: The MEP table entry
cdot1agMepIdentifier: Integer that is unique among all the MEPs in the same MA. Other definition is: a small integer, unique over a given Maintenance Association, identifying a specific Maintenance association End Point (3.19). MEP Identifier is also known as the MEPID. REFERE ...
cdot1agMepIfIndex: This object is the interface index of the interface either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, to which the MEP is attached. Upon a restart of the system, the system SHALL, if necessary, change the value of this variable ...
cdot1agMepDirection: The direction in which the MEP faces on the Bridge port.
cdot1agMepPrimaryVid: An integer indicating the Primary VID of the MEP, always one of the VIDs assigned to the MEP's MA. The value 0 indicates that either the Primary VID is that of the MEP's MA, or that the MEP's MA is associated with no VID.
cdot1agMepActive: Administrative state of the MEP A Boolean indicating the administrative state of the MEP. True indicates that the MEP is to function normally, and false that it is to cease functioning.
cdot1agMepFngState: Current state of the MEP Fault Notification Generator State Machine. REFERENCE 802.1ag clauses 12.14.7.1.3:f and 20.35
cdot1agMepCciEnabled: If set to true, the MEP will generate CCM messages.
cdot1agMepCcmLtmPriority: The priority value for CCMs and LTMs transmitted by the MEP. Default Value in the highest priority value allowed to pass through the bridge port for any of this MEPs VIDs. The management entity can obtain the default value for this variable from the prior ...
cdot1agMepMacAddress: MAC address of the MEP.
cdot1agMepLowPrDef: An integer value specifying the lowest priority defect that is allowed to generate fault alarm. REFERENCE 802.1ag clause 12.14.7.1.3:k and 20.9.5 and Table 20-1
cdot1agMepFngAlarmTime: The time that defects must be present before a Fault Alarm is issued (fngAlarmTime. 20.33.3) (default 2.5s). REFERENCE 802.1ag clauses 12.14.7.1.3:l and 20.33.3
cdot1agMepFngResetTime: The time that defects must be absent before re-enabling a Fault Alarm (fngResetTime, 20.33.4) (default 10s). REFERENCE 802.1ag clauses 12.14.7.1.3:m and 20.33.4
cdot1agMepHighestPrDefect: The highest priority defect that has been present since the MEPs Fault Notification Generator State Machine was last in the FNG_RESET state. REFERENCE 802.1ag clause 12.14.7.1.3:n 20.33.9 and Table 21-1
cdot1agMepDefects: A vector of Boolean error conditions from Table 20-1, any of which may be true: DefRDICCM(0) DefMACstatus(1) DefRemoteCCM(2) DefErrorCCM(3) DefXconCCM(4) REFERENCE .1ag clauses 12.14.7.1.3:o, 12.14.7.1.3:p, 12.14.7.1.3:q, 12.14.7.1.3:r, 12.14.7.1.3:s, 20. ...
cdot1agMepErrorCcmLastFailure: The last-received CCM that triggered an DefErrorCCM fault.
cdot1agMepXconCcmLastFailure: The last-received CCM that triggered a DefXconCCM fault.
cdot1agMepCcmSequenceErrors: The total number of out-of-sequence CCMs received from all remote MEPs. REFERENCE 802.1ag clauses 12.14.7.1.3:v and 20.16.12
cdot1agMepCciSentCcms: Total number of Continuity Check messages transmitted.
cdot1agMepNextLbmTransId: Next sequence number/transaction identifier to be sent in a Loopback message. This sequence number can be zero because it wraps around. REFERENCE 802.1ag clauses 12.14.7.1.3:x and 20.28.2
cdot1agMepLbrIn: Total number of valid, in-order Loopback Replies received.
cdot1agMepLbrInOutOfOrder: The total number of valid, out-of-order Loopback Replies received. REFERENCE 802.1ag clause 12.14.7.1.3:z and 20.31.1
cdot1agMepLbrBadMsdu: (optional) The total number of LBRs received whose mac_service_data_unit did not match (except for the OpCode) that of the corresponding LBM (20.2.3). REFERENCE 802.1ag clause 12.14.7.1.3:aa 20.2.3
cdot1agMepLtmNextSeqNumber: Next transaction identifier/sequence number to be sent in a Linktrace message. This sequence number can be zero because it wraps around. REFERENCE 802.1ag clause 12.14.7.1.3:ab and 20.36.1
cdot1agMepUnexpLtrIn: The total number of unexpected LTRs received (20.39.1). REFERENCE 802.1ag clause 12.14.7.1.3:ac 20.39.1
cdot1agMepLbrOut: Total number of Loopback Replies transmitted.
cdot1agMepTransmitLbmStatus: A Boolean flag set to true by the bridge port to indicate that another LBM may be transmitted. Reset to false by the MEP Loopback Initiator State Machine.
cdot1agMepTransmitLbmDestMacAddress: The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column cdot1agMepTransmitLbmDestIsMepId is 'false'. REFERENCE 802.1ag clause 12.14.7.3.2:b
cdot1agMepTransmitLbmDestMepId: The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the LBM is to be sent. This address will be used if the value of the column cdot1agMepTransmitLbmDestIsMepId is 'true'. REFERENCE 802.1ag clause 1 ...
cdot1agMepTransmitLbmDestIsMepId: True indicates that MEPID of the target MEP is used for Loopback transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmission. REFERENCE 802.1ag clause 12.14.7.3.2:b
cdot1agMepTransmitLbmMessages: The number of Loopback messages to be transmitted.
cdot1agMepTransmitLbmDataTlv: An arbitrary amount of data to be included in the Data TLV, if the Data TLV is selected to be sent. REFERENCE 802.1ag clause 12.14.7.3.2:d
cdot1agMepTransmitLbmVlanPriority: Priority. 3 bit value to be used in the VLAN tag, if present in the transmitted frame. The default value is CCM priority. REFERENCE 802.1ag clause 12.14.7.3.2:e
cdot1agMepTransmitLbmVlanDropEnable: Drop Enable bit value to be used in the VLAN tag, if present in the transmitted frame. For more information about VLAN Drop Enable, please check IEEE 802.1ad. REFERENCE 802.1ag clause 12.14.7.3.2:e
cdot1agMepTransmitLbmResultOK: Indicates the result of the operation: - true The Loopback Message(s) will be (or has been) sent. - false The Loopback Message(s) will not be sent. REFERENCE 802.1ag clause 12.14.7.3.3:a
cdot1agMepTransmitLbmSeqNumber: The Loopback Transaction Identifier (cdot1agMepNextLbmTransId) of the first LBM (to be) sent. The value returned is undefined if cdot1agMepTransmitLbmResultOK is false. REFERENCE 802.1ag clause 12.14.7.3.3:a
cdot1agMepTransmitLtmStatus: A Boolean flag set to true by the bridge port to indicate that another LTM may be transmitted. Reset to false by the MEP Linktrace Initiator State Machine.
cdot1agMepTransmitLtmFlags: The flags field for LTMs transmitted by the MEP.
cdot1agMepTransmitLtmTargetMacAddress: The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column cdot1agMepTransmitLtmTargetIsMepId is 'false'. REFERENCE 802.1ag clause 12.14.7.4.2:c
cdot1agMepTransmitLtmTargetMepId: An indication of the Target MAC Address Field to be transmitted: The Maintenance association End Point Identifier of another MEP in the same Maintenance Association This address will be used if the value of the column cdot1agMepTransmitLtmTargetIsMepId is ...
cdot1agMepTransmitLtmTargetIsMepId: True indicates that MEPID of the target MEP is used for Linktrace transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmission. REFERENCE 802.1ag clause 12.14.7.4.2:c
cdot1agMepTransmitLtmTtl: The LTM TTL field. Default value, if not specified, is 64. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 by each Linktrace Responder that handles the LTM. The value received in the LTM is returned in the LTR. If 0 on ...
cdot1agMepTransmitLtmResult: Indicates the result of the operation: - true The Linktrace Message will be (or has been) sent. - false The Linktrace Message will not be sent
cdot1agMepTransmitLtmSeqNumber: The LTM Transaction Identifier (cdot1agMepLtmNextSeqNumber) of the LTM sent. The value returned is undefined if cdot1agMepTransmitLtmResult is false. REFERENCE 802.1ag clause 12.14.7.4.3:a
cdot1agMepTransmitLtmEgressIdentifier: Identifies the MEP Linktrace Initiator that is originating, or the Linktrace Responder that is forwarding, this LTM. The low-order six octets contain a 48-bit IEEE MAC address unique to the system in which the MEP Linktrace Initiator or Linktrace Responde ...
cdot1agMepRowStatus: The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated. ::= { cdot1agMepEntry 45 } -- **************************************************************** ...
cdot1agLtrEntry: The Linktrace Reply table entry.
cdot1agLtrSeqNumber: Transaction identifier/Sequence number returned by a previous transmit linktrace message command, indicating which LTM's response is going to be returned. REFERENCE 802.1ag clause 12.14.7.5.2:b
cdot1agLtrReceiveOrder: An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. cdot1agLtrReceiveOrder are assigned sequentially from 1, in the order that the Linktrace Initiator received the LTRs. REFERENCE 802.1ag clause 12.14.7.5.2:c
cdot1agLtrTtl: TTL field value for a returned LTR.
cdot1agLtrForwarded: Indicates if a LTM was forwarded by the responding MP, as returned in the 'FwdYes' flag of the flags field. REFERENCE 802.1ag clauses 12.14.7.5.3:c and 20.36.2.1
cdot1agLtrTerminalMep: A boolean value stating whether the forwarded LTM reached a MEP enclosing its MA, as returned in the Terminal MEP flag of the Flags field. REFERENCE 802.1ag clauses 12.14.7.5.3:d and 20.36.2.1
cdot1agLtrLastEgressIdentifier: An octet field holding the Last Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Last Egress Identifier identifies the MEP Linktrace Initiator that originated, or the Linktrace Responder that forwarded, the LTM to which this LTR ...
cdot1agLtrNextEgressIdentifier: An octet field holding the Next Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Next Egress Identifier Identifies the Linktrace Responder that transmitted this LTR, and can forward the LTM to the next hop. This is the same va ...
cdot1agLtrRelay: Value returned in the Relay Action field.
cdot1agLtrChassisIdSubtype: This object specifies the format of the Chassis ID returned in the Sender ID TLV of the LTR, if any. This value is meaningless if the cdot1agLtrChassisId has a length of 0.
cdot1agLtrChassisId: The Chassis ID returned in the Sender ID TLV of the LTR, if any. The format of this object is determined by the value of the cdot1agLtrChassisIdSubtype object. REFERENCE 802.1ag clauses 12.14.7.5.3:i and 21.5.3.3
cdot1agLtrManAddressDomain: The TDomain that identifies the type and format of the related cdot1agMepDbManAddress object, used to access the SNMP agent of the system transmitting the LTR. Received in the LTR Sender ID TLV from that system. Typical values will be one of (not all inc ...
cdot1agLtrManAddress: The TAddress that can be used to access the SNMP agent of the system transmitting the CCM, received in the CCM Sender ID TLV from that system. If the related object cdot1agLtrManAddressDomain contains the value 'zeroDotZero', this object cdot1agLtrManAddr ...
cdot1agLtrIngress: The value returned in the Ingress Action Field of the LTM.
cdot1agLtrIngressMac: MAC address returned in the ingress MAC address field.
cdot1agLtrIngressPortIdSubtype: Format of the Ingress Port ID.
cdot1agLtrIngressPortId: Ingress Port ID. The format of this object is determined by the value of the cdot1agLtrIngressPortIdSubtype object. REFERENCE 802.1ag clauses 12.14.7.5.3:n and 20.36.2.9
cdot1agLtrEgress: The value returned in the Egress Action Field of the LTM.
cdot1agLtrEgressMac: MAC address returned in the egress MAC address field.
cdot1agLtrEgressPortIdSubtype: Format of the egress Port ID.
cdot1agLtrEgressPortId: Egress Port ID. The format of this object is determined by the value of the cdot1agLtrEgressPortIdSubtype object. REFERENCE 802.1ag clauses 12.14.7.5.3:r and 20.36.2.13
cdot1agLtrOrganizationSpecificTlv: All Organization specific TLVs returned in the LTR, if any. Includes all octets including and following the TLV Length field of each TLV, concatenated together.
cdot1agMepDbTable: The MEP Database. A database, maintained by every MEP, that maintains received information about other MEPs in the Maintenance Domain. The SMI does not allow to state in a MIB that an object in a table is an array. The solution is to take the index (or in ...
cdot1agMepDbEntry: The MEP Database table entry.
cdot1agMepDbRMepIdentifier: Maintenance association End Point Identifier of a remote MEP whose information from the MEP Database is to be returned. REFERENCE 802.1ag clause 12.14.7.6.2:b
cdot1agMepDbRMepState: The operational state of the remote MEP IFF State machines.
cdot1agMepDbRMepFailedOkTime: The time (SysUpTime) at which the IFF Remote MEP state machine last entered either the RMEP_FAILED or RMEP_OK state. REFERENCE 802.1ag clause 12.14.7.6.3:c
cdot1agMepDbMacAddress: The MAC address of the remote MEP.
cdot1agMepDbRdi: State of the RDI bit in the last received CCM (true for RDI=1), or false if none has been received. REFERENCE 802.1ag clauses 12.14.7.6.3:e and 20.19.2
cdot1agMepDbPortStatusTlv: An enumerated value of the Port status TLV received in the last CCM from the remote MEP or the default value psNoPortStateTLV indicating either no CCM has been received, or that nor port status TLV was received in the last CCM. REFERENCE 802.1ag clause 12 ...
cdot1agMepDbInterfaceStatusTlv: An enumerated value of the Interface status TLV received in the last CCM from the remote MEP or the default value isNoInterfaceStatus TLV indicating either no CCM has been received, or that no interface status TLV was received in the last CCM. REFERENCE 8 ...
cdot1agMepDbChassisIdSubtype: This object specifies the format of the Chassis ID received in the last CCM.
cdot1agMepDbChassisId: The Chassis ID. The format of this object is determined by the value of the cdot1agLtrChassisIdSubtype object. REFERENCE 802.1ag clauses 12.14.7.6.3:h and 21.5.3.3
cdot1agMepDbManAddressDomain: The TDomain that identifies the type and format of the related cdot1agMepDbManAddress object, used to access the SNMP agent of the system transmitting the CCM. Received in the CCM Sender ID TLV from that system. Typical values will be one of (not all inc ...
cdot1agMepDbManAddress: The TAddress that can be used to access the SNMP agent of the system transmitting the CCM, received in the CCM Sender ID TLV from that system. If the related object cdot1agMepDbManAddressDomain contains the value 'zeroDotZero', this object cdot1agMepDbMan ...
cdot1agStackGroup: Objects for the Stack group.
cdot1agDefaultMdGroup: Objects for the Default MD Level group.
cdot1agVlanIdGroup: Objects for the VLAN ID group.
cdot1agConfigErrorListGroup: Objects for the CFM Configuration Error List Group.
cdot1agMdGroup: Objects for the Maintenance Domain Group.
cdot1agMaGroup: Objects for the MA group.
cdot1agMepGroup: Objects for the MEP group.
cdot1agMepDbGroup: Objects for the MEP group.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list