CISCO-IETF-MEGACO-MIB Download

cmedLinkIdTable

This table contains a nextLinkId for each Gateway. It provides the manager with the nextLinkId for use in creating new Gateway Table Entries.

cmedLinkIdEntry

This table contains the NextLinkId for this Gateway and is indexed by mediaGatewayId.

cmedNextLinkId

The Next Value for a cmedGatewayLinkId. Assists the manager in selecting a value for cmedGatewayLinkId. Using the TestAndIncr syntax, A Manager will 'lock' this variable, ensuring single access.

cmedGatewayConfigTable

A list of cmedGatewayConfigEntry objects.

cmedGatewayConfigEntry

Entry holding configuration information about a group of Media Gateway Controllers sharing the same signaling link.

cmedGatewayId

The unique Media Gateway Id which identifies this media gateway

cmedGatewayLinkId

The unique link id which identifies the signaling link that this gateway uses to communicate with the Gateway Controllers to form an H.248 association.

cmedGatewayLinkName

A descriptive name of this signaling link / media gateway combination

cmedGatewayIPAddress

The IP address that the Media Gateway Controller will use to communicate with the Media Gateway. This object reflects the IP address over control PVC that user configures in cMediaGwIpConfigTable. The value 0.0.0.0 is returned if the entry is invalid.

cmedGatewayPort

TCP/UDP port number that the Media Gateway Controller will use to communicate with the Media Gateway. The value 0 is returned if the entry is invalid.

cmedGatewayEncodingScheme

The encoding scheme that would be used to encode the H.248 messages that are sent/received to/from the gateway controller

cmedGatewayProtocol

Type of the control protocol in use notApplicable (1) - other (2) - Other (none from the list below) dss1-ip (3) - Q931+ ipdc (4) - IPDC megacov1 (5) - MEGACO/H.248 Version 1 megacov2 (6) - MEGACO/H.248 Version 2 mgcp ...

cmedGatewaySigTptProtocol

Type of the transport protocol that is being used to transport the H.248 signaling traffic

cmedGatewayAdminStatus

The desired state of the gateway. The testing(3) state indicates that no signaling packets can be passed. When a managed system initializes, all gateways start with cmedGatewayAdminStatus in the down(2) state. As a result of either explicit management act ...

cmedGatewayOperStatus

The current operational state of the gateway. up (1) - ready to communicate with MGC down (2) testing(3) - in some test mode unknown(4) - status can not be determined for some reason. The testing(3) state indicates that no signaling packets can be p ...

cmedGatewayLastStatusChange

The value of sysUpTime at the time the associated link entered its current operational status. If the current status was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.

cmedGatewayResetStatistics

This object can be used to reset all statistics collected for this media gateway link so far. Statistics will be reset when the object is SET to 'reset'. Upon reset, the agent changes the value of this object to 'notApplicable'.

cmedGatewayRowStatus

This is used to create new rows, modify existing rows and to delete existing rows.

cmedGwyControllerTable

List of the Media Gateway Controllers that are managed in the network

cmedGwyControllerEntry

Entry holding information about an individual Media Gateway Controller.

cmedGwyControllerId

An unique identification number that is assigned to the gateway controller by the manager

cmedGwyControllerIPAddress

The IP address of the Media Gateway Controller. The value 0.0.0.0 is returned if the entry is invalid.

cmedGwyControllerPort

TCP port of the Media Gateway Controller. The value 0 is returned if the entry is invalid.

cmedGwyControllerAdminStatus

The desired state of the gateway. The testing(3) state indicates that no signaling packets can be passed. When a managed system initializes, all gateways start with cmedGwyControllerAdminStatus in the down(2) state. As a result of either explicit manageme ...

cmedGwyControllerOperStatus

The current operational state of the gateway controller. The standby(3) state indicates that it is in the standby mode and no signaling packets can be passed. If cmedGwyControllerAdminStatus is down(2) then cmedGwyControllerOperStatus should be down(2). I ...

cmedGatewayStatsTable

A list of mediaGatewayTableEntry objects.

cmedGatewayStatsEntry

Entry holding statistics about a group of media Gateway/signaling link pair

cmedNumInMessages

Total number of messages received on the link.

cmedNumInOctets

Total number of octets received on the link.

cmedNumOutMessages

Total number of messages sent on the link.

cmedNumOutOctets

Total number of octets sent on the link.

cmedNumErrors

Total number of signaling-level errors encountered. Includes, but is not limited to, number of bad messages received, number of failures to sent a message and number of other errors.

cmedNumTimerRecovery

Total Number of timer recovery events since the statistics was last reset. This reflects all protocol timers that are supported (For H.248, T - start timer, S - short timer, L - long timer, and Z - long duration timer etc)

cmedTransportNumLosses

Number of times a transport link was lost (excluding switch-over cases). A link loss is defined as loss of communication with the entity (MGC) due to hardware/transient problems in the interface or other related hardware/software

cmedTransportNumSwitchover

Number of times when the signaling was switched over to an alternative link. This includes switchover due to the Handoffs initiated by the gateway controllers

cmedTransportTotalNumAlarms

Total number of all alarms issued for the transport layer.

cmedTransportLastEvent

Last event reported by the transport layer. notApplicable (1) - Invalid/unknown. other (2) - None from the list below. linkUp (3) - Transport link is up. linkLoss (4) - Transport link loss. persistentError (5) - No link - persi ...

cmedTransportLastEventTime

The value of sysUpTime at the time when the event specified by cmedTransportLastEvent occurred. If the last event occurred prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.

cmedLastStatisticsReset

The value of sysUpTime at the time when the statistics were reset. If the reset occurred prior to the last re-initialization of the local network management subsystem, this object contains a zero value.

cmedTermIdTable

This table contains a nextTerminationId for each Gateway. It provides the manager with the nextTerminationId for use in creating a new TerminationsTable Entry.

cmedTermIdEntry

This table contains a nextTerminationId for each Gateway, and is indexed by mediaGatewayId.

cmedNextTerminationId

The Next Value for a MediaGateway TerminationId. Assists the manager in selecting a value for cmedTermId. Using the TestAndIncr syntax, A Manager will 'lock' this variable, ensuring single access.

cmedTerminationsTable

This table contains information about terminations in a media gateway. It is a list of terminations. The number of entries equals to the total number of terminations for all contexts in a gateway.

cmedTerminationsEntry

It contains objects that describe a termination.

cmedTermId

An unique identification number that is assigned to the termination by a media gateway. This is the TerminationId that would be used in the protocol messages that are sent from the gateway

cmedTermName

A descriptive name that would describe this termination and its use. For example, 'emergency-ds0-1' indicating that this termination is reserved as an emergency DS0 channel

cmedTermAdminStatus

The desired state of the termination. The testing(3) state indicates that no connections can be created for this termination. When a managed system initializes, all terminations start with cmedTermAdminStatus in the outOfService(2) state. As a result of ...

cmedTermOperStatus

The current operational state of the termination. The testing(3) state indicates that it is in the testing mode and no connections can be created on it. If cmedTermAdminStatus is outOfService(2) then cmedTermOperStatus should be down(2). If cmedTermAdminS ...

cmedTermInterfaceIdentifier

A number that uniquely identifies the interface in the physical gateway. This is the ifIndex in the ifTable, that this termination would be using to communicate to other gateways

cmedTermPropertyProfileId

This determines the profile of the termination which determines what kind of capabilities this termination has. This is an index into the cmedPropertyProfileTable which identifies all the profile that are available

cmedTermRowStatus

This is used to create new rows in this table, Modify existing rows, and to delete existing rows.

cmedPropertyProfileTable

This table contains a list of the properties supported in a Profile. A Manager builds a Profile of properties, then ties each termination to a defined profile

cmedPropertyProfileEntry

Each row represents a default property of the Property Profile N-entries per mediaGatewayId/PropertyId, one entry per property.

cmedPropertyProfileId

This PropertyProfile Identifier uniquely identifies this set of properties. This is the value each termination would refer, when they would like to support all the properties in this profile

cmedPropertyProfileIndex

This is the index to the PropertyProfile This is just a 'counter' through the cmedPropertyProfile Table. ie, property=1 property=2 etc.

cmedPropertyProfileProperty

The Property supported by this Profile. This is an Object ID (OID) defined in a package MIB to identify a Particular property (such as AnalogLines, Tones etc).

cmedPropertyProfileRowStatus

It is used to create new rows in this table, modify existing rows, and to delete existing rows.

cmedConfig

This group contains of all the configuration Information for a Media Gateway. This group is mandatory for any implementation managing a media gateway or a group of media gateways

cmedStatsGroup

This group contains of all the statistics Information for a Media Gateway. This group is mandatory for any implementation managing a media gateway or a group of media gateways

cmedGwyControllerGroup

This group contains of all the configuration Information for a Media Gateway Controller. This group is mandatory for any implementation managing a media gateway controller or a group of media gateway controllers. It is also mandatory for implementations m ...

cmedNextIdGroup

Agent provides NextId's to the Manager to assist in selecting and creating new table entries. This group is optional for all the implementations. But when it is not implemented, it is the manager's responsibility to uniquely determine these ids

cmedTermGroup

This group contains of all the configuration Information for a termination. This group is mandatory for any implementation managing termination.