CISCO-IPSLA-JITTER-MIB Download

MIBs list

This MIB module defines templates for IP SLA operations of UDP Jitter and ICMP Jitter. The UDP Jitter operation is designed to measure the delay variance and packet loss in IP networks by generating synthetic UDP traffic. The ICMP Jitter operation provides capability to measure metrics such as RTT (Round Trip Time), jitter, packet loss, one-way latency by sending ICMP Timestamp stream to the destination devices.

IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for CISCO-IPSLA-JITTER-MIB

cipslaUdpJitterTmplTable: A table that contains UDP jitter template specific definitions.
cipslaUdpJitterTmplEntry: A row entry representing an IPSLA UDP jitter template.
cipslaUdpJitterTmplName: A string which specifies the UDP Jitter template name.
cipslaUdpJitterTmplDescription: A string which provides description of UDP Jitter template.
cipslaUdpJitterTmplControlEnable: If this object is enabled, then the IP SLA application will send control messages to a responder, residing on the target router to respond to the data request packets being sent by the source router.
cipslaUdpJitterTmplTimeOut: Specifies the duration to wait for a IP SLA operation completion. For connection oriented protocols, this may cause the connection to be closed by the operation. Once closed, it will be assumed that the connection reestablishment will be performed. To p ...
cipslaUdpJitterTmplVerifyData: When set to true, the resulting data in each IP SLA operation is compared with the expected data. This includes checking header information (if possible) and exact packet size.
cipslaUdpJitterTmplCodecType: Specifies the codec type to be used with UDP jitter operation. If codec-type is configured the following parameters cannot be configured. cipslaUdpJitterReqDataSize cipslaUdpJitterInterval cipslaUdpJitterNumPkts
cipslaUdpJitterTmplCodecInterval: This field represents the inter-packet delay between packets and is in milliseconds. This object is applicable only to UDP jitter operation which uses codec type.
cipslaUdpJitterTmplCodecPayload: This object represents the number of octets that needs to be placed into the Data portion of the message. This value is used only for UDP jitter operation which uses codec type.
cipslaUdpJitterTmplCodecNumPkts: This value represents the number of packets that need to be transmitted. This value is used only for UDP jitter operation which uses codec type.
cipslaUdpJitterTmplInterval: This value represents the inter-packet delay between packets and is in milliseconds.
cipslaUdpJitterTmplNumPkts: This value represents the number of packets that need to be transmitted.
cipslaUdpJitterTmplSrcAddrType: An enumerated value which specifies the IP address type of the source. It must be used along with the cipslaUdpJitterTmplSrcAddr object.
cipslaUdpJitterTmplSrcAddr: This field specifies the IP address of the source.
cipslaUdpJitterTmplSrcPort: This object represents the source's port number. If this object is not specified, the application will get a port allocated by the system.
cipslaUdpJitterTmplPrecision: This object specifies the accuracy of jitter statistics in rttMonJitterStatsTable that needs to be calculated. milliseconds(1) - The accuracy of stats will be of milliseconds. microseconds(2) - The accuracy of stats will be in microseconds.
cipslaUdpJitterTmplReqDataSize: This object represents the number of octets to be placed into the ARR Data portion of the request message, when using SNA protocols. For non-ARR protocols' IP SLA request/responses, this value represents the native payload size. REMEMBER: The ARR Header ...
cipslaUdpJitterTmplPktPriority: This object specifies the priority that will be assigned to operation packet. normal(1) - The packet is of normal priority. high(2) - The packet is of high priority.
cipslaUdpJitterTmplTOS: This object represents the type of service octet in an IP header.
cipslaUdpJitterTmplVrfName: This field is used to specify the VRF name in which the IP SLA operation will be used. For regular IP SLA operation this field should not be configured. The agent will use this field to identify the VPN routing table for this operation.
cipslaUdpJitterTmplThreshold: This object defines an administrative threshold limit. If the IP SLA operation time exceeds this limit, then one threshold crossing occurrence will be counted.
cipslaUdpJitterTmplNTPTolAbs: This object specifies the total clock synchronization error on source and responder that is considered tolerable for oneway measurement when NTP is used as clock synchronization mechanism. The total clock synchronization error is sum of NTP offsets on so ...
cipslaUdpJitterTmplNTPTolPct: This object specifies the total clock synchronization error on source and responder that is considered tolerable for oneway measurement when NTP is used as clock synchronization mechanism. The total clock synchronization error is sum of NTP offsets on so ...
cipslaUdpJitterTmplNTPTolType: This object specifies whether the value specified for oneway NTP sync tolerance is absolute value or percent value. percent(1) - The value for oneway NTP sync tolerance is absolute value. absolute(2) - The value for oneway NTP sync tolerance is percent v ...
cipslaUdpJitterTmplIcpifFactor: The advantage factor is dependant on the type of access and how the service is to be used. Conventional Wire-line 0 Mobility within Building 5 Mobility within geographic area 10 Access to hard-to-reach location 20 It is used when calculating the ...
cipslaUdpJitterTmplStatsHours: The maximum number of hours for which statistics are maintained. Specifically this is the number of hourly groups to keep before rolling over. The value of one is not advisable because the hourly group will close and immediately be deleted before the netw ...
cipslaUdpJitterTmplDistBuckets: The maximum number of statistical distribution buckets to accumulate. Since this index does not rollover, only the first cipslaUdpJitterTmplDistBuckets will be kept. The last bucket will contain all entries from its distribution interval start point to in ...
cipslaUdpJitterTmplDistInterval: The statistical distribution buckets interval. Distribution Bucket Example: cipslaUdpJitterTmplDistBuckets = 5 buckets cipslaUdpJitterTmplDistInterval = 10 milliseconds | Bucket 1 | Bucket 2 | Bucket 3 | Bucket 4 | Bucket 5 | | 0-9 ms | 10-19 ms | 20-2 ...
cipslaUdpJitterTmplStorageType: The storage type of this conceptual row.
cipslaUdpJitterTmplRowStatus: The status of the conceptual UDP Jitter template control row. When the status is active, all the read-create objects in that row can be modified.
cipslaIcmpJitterTmplTable: A table that contains ICMP jitter template specific definitions.
cipslaIcmpJitterTmplEntry: A row entry representing an IP SLA ICMP Jitter template.
cipslaIcmpJitterTmplName: A string which specifies the ICMP jitter template name.
cipslaIcmpJitterTmplDescription: A string which provides description of ICMP Jitter template.
cipslaIcmpJitterTmplTimeOut: Specifies the duration to wait for a IP SLA operation completion. For connection oriented protocols, this may cause the connection to be closed by the operation. Once closed, it will be assumed that the connection reestablishment will be performed. To p ...
cipslaIcmpJitterTmplVerifyData: When set to true, the resulting data in each IP SLA operation is compared with the expected data. This includes checking header information (if possible) and exact packet size.
cipslaIcmpJitterTmplNumPkts: This value represents the number of packets that need to be transmitted.
cipslaIcmpJitterTmplInterval: This value represents the inter-packet delay between packets and is in milliseconds.
cipslaIcmpJitterTmplSrcAddrType: An enumerated value which specifies the IP address type of the source. It must be used along with the cipslaIcmpJitterTmplSrcAddr object.
cipslaIcmpJitterTmplSrcAddr: A string which specifies the IP address of the source.
cipslaIcmpJitterTmplTOS: This object represents the type of service octet in an IP header.
cipslaIcmpJitterTmplVrfName: This field is used to specify the VRF name in which the IP SLA operation will be used. For regular IP SLA operation this field should not be configured. The agent will use this field to identify the VPN routing Table for this operation.
cipslaIcmpJitterTmplThreshold: This object defines an administrative threshold limit. If the IP SLA operation time exceeds this limit, then one threshold crossing occurrence will be counted.
cipslaIcmpJitterTmplStatsHours: The maximum number of hourss for which statistics are maintained. Specifically this is the number of hourly groups to keep before rolling over. The value of one is not advisable because the hourly group will close and immediately be deleted before the net ...
cipslaIcmpJitterTmplDistBuckets: The maximum number of statistical distribution buckets to accumulate. Since this index does not rollover, only the first cipslaIcmpJitterTmplDistBuckets will be kept. The last bucket will contain all entries from its distribution interval start point to i ...
cipslaIcmpJitterTmplDistInterval: The statistical distribution buckets interval. Distribution Bucket Example: cipslaIcmpJitterTmplDistBuckets = 5 buckets cipslaIcmpJitterTmplDistInterval = 10 milliseconds | Bucket 1 | Bucket 2 | Bucket 3 | Bucket 4 | Bucket 5 | | 0-9 ms | 10-19 ms | 20 ...
cipslaIcmpJitterTmplStorageType: The storage type of this conceptual row.
cipslaIcmpJitterTmplRowStatus: The status of the conceptual ICMP jitter template control row. When the status is active, all the read-create objects in that row can be modified.
ciscoIpSlaUdpJitterTmplGroup: A collection of objects related to UDP Jitter Template.
ciscoIpSlaIcmpJitterTmplGroup: A collection of objects related to ICMP Jitter Template.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list