CISCO-OPTICAL-MONITOR-MIB Download

cOpticalMonTable

This table provides objects to monitor optical parameters in a network element. It also provides objects for setting high and low threshold levels, with configurable severities, on these monitored parameters.

cOpticalMonEntry

An entry in the cOpticalMonTable provides objects to monitor an optical parameter and set threshold levels on that parameter, at an optical interface. Note that the set of monitored optical parameters may vary based on interface type, direction, and monit ...

cOpticalMonDirection

This object indicates the direction monitored for the optical interface, in this entry.

cOpticalMonLocation

This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or attenuation), at this interface.

cOpticalMonParameterType

This object specifies the optical parameter that is being monitored in this entry.

cOpticalParameterValue

This object gives the value measured for the particular optical parameter specified by the cOpticalMonParameterType object.

cOpticalParamHighAlarmThresh

This object is used to set a high alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from below the value configured in this object to above the value configured in ...

cOpticalParamHighAlarmSev

This object is used to specify a severity level associated with the high alarm threshold given by the cOpticalParamHighAlarmThresh object. The values 'notAlarmed', 'notReported', and 'cleared' do not apply. The severity level configured in this object mus ...

cOpticalParamHighWarningThresh

This object is used to set a high warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by cOpticalParameterValue goes from below the value configured in this object to above the va ...

cOpticalParamHighWarningSev

This object is used to specify a severity level associated with the high warning threshold given by the cOpticalParamHighWarningThresh object. The values 'critical', 'major', and 'cleared' do not apply. The severity level configured in this object must be ...

cOpticalParamLowAlarmThresh

This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from above the value configured in this object to below the value configured in ...

cOpticalParamLowAlarmSev

This object is used to specify a severity level associated with the low alarm threshold given by the cOpticalParamLowAlarmThresh object. The values 'notAlarmed', 'notReported', and 'cleared' do not apply. The severity level configured in this object must ...

cOpticalParamLowWarningThresh

This object is used to set a low warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by cOpticalParameterValue goes from above the value configured in this object to below the val ...

cOpticalParamLowWarningSev

This object is used to specify a severity level associated with the low warning threshold given by the cOpticalParamLowWarningThresh object. The values 'critical', 'major', and 'cleared' do not apply. The severity level configured in this object must be l ...

cOpticalParamAlarmStatus

This object is used to indicate the current status of the thresholds for the monitored optical parameter on the interface. If a threshold is currently being exceeded on the interface, the corresponding bit in this object will be set to 1. Otherwise, the b ...

cOpticalParamAlarmCurMaxThresh

This object indicates the threshold value of the highest severity threshold that is currently being exceeded on the interface, for the optical parameter. If no threshold value is currently being exceeded, then the value '-1000000' is returned.

cOpticalParamAlarmCurMaxSev

This object indicates the maximum severity of any thresholds that are currently being exceeded on the interface, for the optical parameter.

cOpticalParamAlarmLastChange

This object specifies the value of sysUpTime at the last time a threshold related to a particular optical parameter was exceeded or cleared on the interface.

cOpticalMon15MinValidIntervals

This object gives the number of previous 15 minute intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be n (where n is the maximum number of 15 minute intervals supported at this interface ...

cOpticalMon24HrValidIntervals

This object gives the number of previous 24 hour intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be 0 if the measurement was (re-)started within the last 24 hours, or 1 otherwise.

cOpticalParamThreshSource

This object indicates if the current value of a particular threshold in this entry is user configured value or it is a system default value. It also allows user to specify the list of thresholds for this entry which should be restored to their system defa ...

cOpticalNotifyEnable

This object specifies the minimum severity threshold governing the generation of cOpticalMonParameterStatus notifications. For example, if the value of this object is set to 'major', then the agent generates these notifications if and only if the severity ...

cOpticalMonEnable

This object specifies the types of transceivers for which optical monitoring is enabled. A value of 1 for the bit 'all', specifies that optical monitoring functionality is enabled for all the types of transceivers which are supported by system and have op ...

cOpticalMonPollInterval

This object specifies the interval in minutes after which optical transceiver data will be polled by system repeatedly and updated in cOpticalMonTable when one or more bits in cOpticalMonEnable is set.

cOpticalMonIfTable

This table contains the list of optical interfaces populated in cOpticalMonTable.

cOpticalMonIfEntry

An entry containing the information for a particular optical interface.

cOpticalMonIfTimeInSlot

This object indicates when this optical transceiver was detected by the system.

cOpticalPMCurrentTable

This table contains performance monitoring data for the various optical parameters, collected over the current 15 minute or the current 24 hour interval.

cOpticalPMCurrentEntry

An entry in the cOpticalPMCurrentTable. It contains performance monitoring data for a monitored optical parameter at an interface, collected over the current 15 minute or the current 24 hour interval. Note that the set of monitored optical parameters may ...

cOpticalPMCurrentPeriod

This object indicates whether the optical parameter values given in this entry are collected over the current 15 minute or the current 24 hour interval.

cOpticalPMCurrentDirection

This object indicates the direction monitored for the optical interface, in this entry.

cOpticalPMCurrentLocation

This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or attenuation), at this interface.

cOpticalPMCurrentParamType

This object specifies the optical parameter that is being monitored, in this entry.

cOpticalPMCurrentMaxParam

This object gives the maximum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval.

cOpticalPMCurrentMinParam

This object gives the minimum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval.

cOpticalPMCurrentMeanParam

This object gives the average value of the monitored optical parameter, in the current 15 minute or the current 24 hour interval.

cOpticalPMCurrentUnavailSecs

This object is used to indicate the number of seconds, in the current 15 minute or the current 24 hour interval, for which the optical performance data is not accounted for. In the receive direction, the performance data could be unavailable during these ...

cOpticalPMIntervalTable

This table stores performance monitoring data for the various optical parameters, collected over previous intervals. This table can have entries for one complete 24 hour interval and up to 96 complete 15 minute intervals. A system is required to store at ...

cOpticalPMIntervalEntry

An entry in the cOpticalPMIntervalTable. It contains performance monitoring data for an optical parameter, collected over a previous interval. Note that the set of monitored optical parameters may vary based on interface type, direction, and monitoring lo ...

cOpticalPMIntervalPeriod

This object indicates whether the optical parameter values, given in this entry, are collected over a period of 15 minutes or 24 hours.

cOpticalPMIntervalNumber

A number between 1 and 96, which identifies the interval for which the set of optical parameter values is available. The interval identified by 1 is the most recently completed 15 minute or 24 hour interval, and the interval identified by N is the interva ...

cOpticalPMIntervalDirection

This object indicates the direction monitored for the optical interface, in this entry.

cOpticalPMIntervalLocation

This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or attenuation), at this interface.

cOpticalPMIntervalParamType

This object specifies the optical parameter that is being monitored, in this entry.

cOpticalPMIntervalMaxParam

This object gives the maximum value measured for the optical parameter, in a particular 15 minute or 24 hour interval.

cOpticalPMIntervalMinParam

This object gives the minimum value measured for the optical parameter, in a particular 15 minute or 24 hour interval.

cOpticalPMIntervalMeanParam

This object gives the average value of the measured optical parameter, in a particular 15 minute or 24 hour interval.

cOpticalPMIntervalUnavailSecs

This object is used to indicate the number of seconds, in the particular 15 minute or 24 hour interval, for which the optical performance data is not accounted for. In the receive direction, the performance data could be unavailable during these periods f ...

cOpticalMIBMonGroup

A mandatory object that provides monitoring of optical characteristics.

cOpticalMIBThresholdGroup

A collection of objects that support thresholds on optical parameters and provide status information when the thresholds are exceeded or cleared.

cOpticalMIBSeverityGroup

A collection of objects that support severities for thresholds on optical parameters.

cOpticalMIBPMGroup

A collection of objects that provide optical performance monitoring data for 15 minute and 24 hour intervals.

cOpticalMIBNotifyEnableGroup

An object to control the generation of notifications.

cOpticalMonIfTimeGroup

A collection of object(s) that provide time related information for transceivers in the system.

cOpticalMIBEnableConfigGroup

A collection of object(s) to enable/disable optical monitoring.

cOpticalMIBIntervalConfigGroup

A collection of object(s) to specify polling interval for monitoring optical transceivers.

cOpticalMonThreshSourceGroup

A collection of object(s) to restore a given threshold to its default value.