CISCO-PAGP-MIB Download

pagpEtherChannelTable

The pagpEtherChannelTable specifies, per physical interface, the Fast Etherchannel operational mode (off, manual, or protocol-controlled) and the capability of the interface to form aggregations. Interfaces that do not support Fast Etherchannel or PAgP d ...

pagpEtherChannelEntry

The entry describes the permitted interface aggregation. Entries are created by the managed system for each interface which supports Fast Etherchannel.

pagpEthcOperationMode

The managed device will refuse a request to set pagpEthcOperationMode to the pagpOn(3) state if the device does not implement the PAgP protocol. The managed device will refuse to set pagpEthcOperationMode to manual(2) or pagpOn(3) if the values in the in ...

pagpDeviceId

Uniquely identifies a device which implements Fast Etherchannel. The combination of pagpDeviceId and ifIndex must be unique over all interfaces in a network. pagpDeviceId typically identifies a device such as a bridge, router, or file server, but may be ...

pagpPhysGroupCapability

The values in pagpPhysGroupCapability indicate the aggregation capability of the underlying hardware. The speed, configuration, and status condition of the interface, e.g. ISL protocol on/off, ifOperStatus On/Off, full-/half-duplex, etc., does not affect ...

pagpOperGroupCapability

This variable informs the system administrator examining the Fast Etherchannel MIB of the capabilities of the current state of the interface's hardware to form agports. The pagpOperGroupCapability values are adjusted automatically by the managed system to ...

pagpAdminGroupCapability

pagpAdminGroupCapability is used by the network administrator to control the aggregation of interfaces into agports. The default value of pagpAdminGroupCapability is equal to the value of pagpPhysGroupCapability on that same interface. A pagpAdminGroupCa ...

pagpPortPriority

The priority of this interface relative to other interfaces when determining which interface is to be used in Hot Standby mode. Among all interfaces aggregated together with a single agport, the one with the highest numerical value of pagpPortPriority is ...

pagpLearnMethod

This interface's learning method value. Specifies whether this device is able to learn the location of a source MAC address based on the agport on which it was received, agPort(2), or on the interface on which it was received, physPort(1). This value is ...

pagpGroupIfIndex

If pagpGroupIfIndex is 0, then the inteface is not aggregated to an agport, and is unavailable for normal data reception and transmission. If pagpGroupIfIndex equals the interface's own ifIndex, the interface is aggregated to itself, and behaves as a sing ...

pagpDistributionProtocol

pagpDistributionProtocol controls the load balancing algorithms used on this interface's agport to distribute outgoing data frames among its component interfaces, such as IP address. Configuring pagpDistributionProtocol on this interface may result in hav ...

pagpDistributionAddress

pagpDistributionAddress controls the type of distribution on the configured pagpDistributionProtocol used on this interface's agport to distribute outgoing data frames among its component interfaces. For example if the pagpDistributionProtocol is configur ...

pagpRate

Specifies the rate at which the PAgP packets are transmitted on this interface. fast(1) : PAgP packets are transmitted at the fast rate on this interface. normal(2) : PAgP packets are transmitted at the normal rate on this interface.

pagpInPacketTimeout

Specifies the earliest time at which received PAgP information packets are timed out.

pagpProtocolConfigTable

The table of per-interface Port Aggregation Protocol variables. Physical interfaces that support Fast Etherchannel and PAgP protocol have an entry in this table. If the value of pagpEthcOperationMode for the corresponding interface is off(1) or manual(2) ...

pagpProtocolConfigEntry

The entry describes the operational state of the PAgP protocol on a particular physical interface. Entries in this table are for interfaces that support both Fast Etherchannel and PAgP protocol. The agport itself is not represented in this table.

pagpOperationMode

Controls the operational mode of the PAgP protocol on this interface.

pagpPortState

The state of the PAgP state machine on this interface. Values: portDown(1) - interface's ifOperStatus is not Up; portUp(2) - interface's ifOperStatus is Up, no packets yet received; dataReceived(3) - data packets, but no PAgP packets, have b ...

pagpLastStateChange

Value of sysUpTime the last time that pagpPortState changed.

pagpHelloFrequency

If pagpHelloFrequency is slow(2), this device uses a 105 second timer on this interface to time out receipt of PAgP packet. If fast(1), this device uses a 3.5 second timer. PAgP uses fast(1) by default. This value is set to slow(2) by action of the PAgP ...

pagpDistributionAlgorithm

pagpDistributionAlgorithm describes, in human terms, the method used on this interface's agport to distribute outgoing data frames among its component interfaces. 'Source MAC address', 'Source and Destination MAC addresses', or 'IP flow: Source, Destinat ...

pagpPartnerCount

The number of other devices known to be transmitting PAgP packets to this device on this physical interface. If pagpPartnerCount contains none(1), then the values of the remainder of the variables in this section are as defined by each variable for this c ...

pagpPartnerDeviceId

MAC Address of the partner, obtained from the PAgP packet last received on this interface. Contains all 0 if pagpPartnerCount contains none(1).

pagpPartnerLearnMethod

The value of the partner's pagpLearnMethod value, obtained from the PAgP packet last received on this interface. undefined(3) if pagpPartnerCount contains none(1).

pagpPartnerPortPriority

The value of the partner's pagpPortPriority, obtained from the PAgP packet last received on this interface. 0 if pagpPartnerCount contains none(1).

pagpPartnerIfIndex

The value of the partner's ifIndex value, obtained from the PAgP packet last received on this interface. 0 if pagpPartnerCount contains none(1). Use CISCO-CDP-MIB cdpCacheTable to resolve the partner's IP Address and get ifTable information for this ifIn ...

pagpPartnerGroupCapability

The value of the partner's pagpOperGroupCapability obtained from the PAgP packet last received on this interface. 0 if pagpPartnerCount contains none(1)

pagpPartnerGroupIfIndex

The value of the partner's pagpGroupIfIndex obtained from the PAgP packet last received on this interface. 0 if pagpPartnerCount contains none(1).

pagpPartnerDeviceName

The DisplayString obtained from the PAgP packet last received on this interface. 0-length string if pagpPartnerCount contains none(1), or if no device name has been received. The value transmitted in a PAgP information packet should be the sysName value ...

pagpPartnerPortName

The DisplayString obtained from the PAgP packet last received on this interface. 0-length string if pagpPartnerCount contains none(1), or if no port name has been received. The value transmitted in a PAgP packet should be the ifName value of the interfac ...

pagpPartnerAgportMACAddress

The MacAddress obtained from the PAgP packet last received on this interface. All 0 if pagpPartnerCount contains none(1) or if no agport MacAddress has been received in a PAgP packet. If this value is not all 0, then the device sending the TLV is promisi ...

pagpProtocolStatsTable

The table of per-interface Port Aggregation Protocol statistics. The entries in this table are present only on an interface that is capable both of implementing Fast Etherchannel, and can be controlled by the PAgP protocol. The agport itself is not repre ...

pagpProtocolStatsEntry

The entry describes the accumulated statistics of the PAgP protocol operation on the aggregated interface.

pagpInPackets

Number of PAgP information packets received on this interface.

pagpOutPackets

Number of PAgP information packets transmitted on this interface.

pagpInFlushes

Number of PAgP flush packets received and echoed on this interface not matching any pagpDeviceId belonging to the managed device. This counts PAgP flush packets originated by another device, and indicates that the other device 1) implements the PAgP flus ...

pagpReturnedFlushes

Number of PAgP flush packets received on this interface matching some pagpDeviceId belonging to this device. This counts PAgP flush packets which were originated by the managed device and returned to it by another device, and indicates that 1) the manage ...

pagpOutFlushes

Number of PAgP flush packets generated on this interface. Does not count flush packets counted in pagpInFlushes and returned to the sender. If pagpOutFlushes is counting and pagpReturnedFlushes is not, the other device may not be returning PAgP flush pa ...

pagpInErrors

Number of packet received on this interface which were identified by the encapsulation as being PAgP packets (of any type, e.g. information or flush), but which were not valid packets because of length, version, number of TLVs, or an illegal value in an e ...

ciscoPagpEthcGroupV1R1

The collection of objects which are used to configure and monitor the Fast Etherchannel operation and interface group-capability.

ciscoPagpPagpGroupV1R1

The collection of objects which are used to configure and monitor the Port Aggregation Protocol (PAgP) for the automatic negotiation and configuration of Fast Etherchannel.

ciscoPagpEthcGroupV2R2

The collection of objects which are used to configure and monitor the Fast Etherchannel operation and interface group-capability.

ciscoPagpRateAndTimeOutGroup

A collection of objects which provide the information about rate and timeout configuration for PAgP protocol on capable interfaces.