CISCO-WAN-BBIF-PORT-MIB Download
The MIB module for configuration of ATM logical
ports in PXM1 Service module in MGX82xx series.
This MIB contains information on ATM Logical
port statistics.
IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for CISCO-WAN-BBIF-PORT-MIB
- bbIfCnfPortGrpTable
- The Broadband Interface config table is for logical interface. There will an entry for each of the logical partition of the physical line. ::= { bbIfCnfPortGrp 1 } SYNTAX BbIfCnfPortGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION
- bbIfNum
- This is logical interface number within a physical line num. In MGX PXM1 card, a physical port can have a maximum of 32 logical interfaces.
- bbIfRowStatus
- This variable enables or disables the logical interface. 1 - enable 2 - disable 3 - modify
- bbIfAdmin
- This variable enables or disables the logical interface. 1 - up 2 - down 3 - writeOnly
- bbIfLineNum
- The line number associated with the logical interface. For PXM1, there is currently 4 physical lines.
- bbIfIngrPctBandwidth
- The percentage of aggregate physical line bandwidth, available for this broadband interface - Ingress. Default is 0 %.
- bbIfEgrPctBandwidth
- The percentage of aggregate physical line bandwidth, available for this broadband interface - Egress . Default is 0 %.
- bbIfMinVpi
- The lower limit of VPI range to be reserved for this logical interface.
- bbIfMaxVpi
- The upper limit of VPI range to be reserved for this logical interface. For virtual trunks, bbIfMinVpi and bbIfMaxVpi should be the same.
- bbIfSpeed
- The speed of the port in cells per second.
- bbIfMaxCellRatePct
- The maximum cell rate allowed for the port in terms of percentage. Must be greater than or equal to bbIfIngrPctBandwidth. The default is 100 percent.
- nextBbIfNumAvailable
- Indicates the next logical broadband interface number that is available.
- bbIfStateGrpTable
- The state table for the logical interface.
- bbIfStateGrpEntry
- An entry for each logical interface representing the state.
- bbStateIfNum
- This is logical interface number within a physical line num. In MGX PXM1 card, a physical port can have a maximum of 32 logical interfaces.
- bbIfState
- This variable indicates the status of the logical interface. The following values are not supported for the logical interface. remoteloopback (3), outofcelldelineation (6), localloopback (7).
- bbIfOversubscribed
- This variable indicates the whether the logical interface is over subscribed or not.
- bbIfIngrPercentUtil
- Percentage Utilization of the interface in the Ingress direction.
- bbIfEgrPercentUtil
- Percentage Utilization of the interface in the Egress direction.
- bbIfCntGrpTable
- The Broadband Interface Count table is for logical interface. There will an entry for each of the logical partition of the physical line.
- bbIfCntGrpEntry
- An entry for logical interface.
- bbCntIfNum
- Refers to the logical interface index.
- bbIfTotalCells
- Total number of cells (VC plus Qbin) that belong to this Interface. This maps on to the virtual interface of QE.
- bbIfRcvValidOAMCells
- Total number of OAM cell received.
- bbIfRcvRmCells
- Total number of RM cells Received.
- bbIfRcvClp0Cells
- Total number of CLP-0 cells Received.
- bbIfRcvClp1Cells
- Total number of CLP-1 cells Received.
- bbIfRcvClp0DiscCells
- Total number of CLP-0 cells discarded at Ingress.
- bbIfRcvClp1DiscCells
- Total number of CLP-1 cells discarded at Ingress.
- bbIfXmtOAMCells
- Total number of OAM cells transmitted.
- bbIfXmtRmCells
- Total number of RM cells transmitted.
- bbIfXmtClp0Cells
- Total number of CLP-0 cells transmitted.
- bbIfXmtClp1Cells
- Total number of CLP-1 cells transmitted.
- bbIfCntClrButton
- Writing a value of 2 resets all the counters.
- bbIfRcvErroredCells
- Total number of cells with Invalid VPI VCI or Invalid PTI fields This is a card level counter and hence will be the same for all instances of the ports.
- cwbPortGenearlGroup
- The collection of objects which are applicable for general information about logical ports.
- cwbPortConfGroup
- The collection of objects which are used for configuring ATM logical ports(known as broad band interface ports).
- cwbPortStateGroup
- The collection of objects which are used for finding the state of ATM logical ports(known as broad band interface ports).
- cwbPortStatsGroup
- The collection of objects containing the statistics information for ATM Logical ports.
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
