CISCO-WAN-CES-CONN-MIB Download

cesmChanCnfGrpTable

This table contains the configuration information for connection endpoints.

cesmChanCnfGrpEntry

An entry in the cesmChanCnfGrpTable. The each entry corresponds to a connection endpoint identified by following objects: - cesCnfChanNum : Channel Number - cesChanPortNum: Logical Port Number - VPI/VCI value for local/remote endpoints - NSAP Addresses fo ...

cesCnfChanNum

This object identifies the channel number of the CESM channel. For CESM-4P the range is 16..19 (only for 4 entries). For CESM-8t1 the range is 16..192 For CESM-8e1 the range is 16..248. For CESM-T3/E3 the range is 16..16. For CESM-T1/E1/T3/E3, channel nu ...

cesChanRowStatus

This object is used to create,modify or delete an entry in the table. A row need to be created using 'add' option. When the row is successfully created, this object would be set to 'mod' by the agent. Following mandatory objects need to be specified for t ...

cesMapPortNum

This object provides the mapping from CES channel number and physical line number. In case of CESM-4P this variable specifies the port number to which this channel is associated. Mappings are as follows: Port 1 - channel 16, 2-17, 3-18, 4-19 (it can tak ...

cesMapVpi

The value of this object is equal to the VPI used for the emulated circuit represented by this connection. In MGX8220( formerly AXIS) Implementaion slot number of the card will be used for this.

cesMapVci

This specifies VCI for emulated circuit represented by this VC. Our Implementation cesCnfChanNum will be used for this. In case of CESM-4P valid range is 16..19. In case of CESM-8P valid range is 32..279. In case of CESM-T3/E3 valid value is 32.

cesCBRService

This specifies data type supported by the CBR service. unstructured(1) : This is also known as 'clear channel'. This service utilizes the entire T1 bandwidth. The switch does not look into the T1, but simply reproduces a stream of bits with clocking from ...

cesCBRClockMode

This specifies clocking mode of the CBR service. synchronous(1) : The transmit clock frequency is produced by an external source. srts (2) : Synchronous Residual TimeStamp(SRTS) is an asnychronous clocking method. The SRTS measures the difference be ...

cesCas

This object specifies whether CAS bits are carried by the service. This also selects which AAL1 format should be used. The possible values are : basic(1) : for 1x64 connections, cells will be generated with a AAL1 pointer. While receiving, pointer will be ...

cesPartialFill

Specifies the number of user octets per cell, if partial cell fill is used. 47 means partial fill disabled. Partial fill is not supported in CESM-4P Ranges for partial fill are: T1 struct 25 - 47 T1 unstruct 33 - 47 E1 struct 20 - 47 E1 unstruct ...

cesBufMaxSize

Specifies the maximum size in octets of egress buffer. CESM - 4P: Should be at least 0.6*CDVRxT for a T1 line and 0.7 * CDVRxT for a E1 line. 0 can be specified to internally compute the value Defaults for CESM-8T1E1 and CESM-T3E3 ----------------------- ...

cesCellLossIntegrationPeriod

This object specifies the cell loss integration period.

cesChanLocRmtLpbkState

Loopback on cellbus in egress direction.

cesChanTestType

This is the type of the test 1 = Test Continuity 2 = Test Delay 3 = no test is initated 4 = test continuity with sti cell format 5 = test delay with sti cell format DEFVAL { notest} ::= { cesmChanCnfGrpEntry 14} SYNTAX INTEGER { passed(1), failed(2), in ...

cesChanPortNum

This object refers to the CES logical port on which channel is created. The value for this object must be same as the 'cesPortNum' object from cesmPortCnfGrpTable. This is a mandatory object for creating the channel.

cesChanConnType

This object identifies the type of the connection. The possible values are : pvc(1) : Permanent Virtual Connection svc(2) : Switched Virtual Connection spvc(3) : Soft PVC Only applicable to CESM-8P and CESM-T3/E3. This object can be specified only d ...

cesChanStrauSciNum

This indicates the type of connection. 1 = Normal Channel (nonStrauChannel(0) ) 2 = SCI 1 i.e bit 1 & 2 3 = SCI 2 i.e bit 3 & 4 4 = SCI 3 i.e bit 5 & 6 5 = SCI 4 i.e bit 7 & 8 Currently not supported in CESM-8 Not applicable for CESM-4 and CESM-T3/E3 DEFV ...

cesChanIdleSignalCode

This object identifies the signal code to be sent. The value indicates the idle pattern in DS0 time slots. This object is applicable only when cesChanIdleDetEnable object is set to enableIdlePatternDet(3).

cesChanIdleCodeIntgnPeriod

This object indicates the Integration period in seconds This object is applicable only when cesChanIdleDetEnable is set to enableIdlePatternDet(3).

cesChanOnhookCode

This object identifies the on-hook code to be sent. This object is applicable only when cesChanIdleDetEnable object is set to enableOnhookDet(2). The value 0..3 is applicable for T1 with framing mode set to super frame(SF). The value 0..15 is applicable f ...

cesChanConditionedData

This byte will indicate Idle data to be sent towards the line whenever channels goes in to Underrun Only applicable for CESM-8T1/E1.

cesmChanExtTrgIdleSupp

This object is used for disabling/enabling idle suppression on the connection. This can be set by external signalling device. Only applicable to CESM-8T1/E1.

cesmChanConditionedSigCode

This byte will indicate Signal code to be sent sent towards the line whenever channels goes in to Underrun Only applicable to CESM-8T1/E1.

cesLocalVpi

This object identifies the internal VPI assigned to a local endpoint, by the switch. The cesLocalVpi, cesLocalVci and cesLocalNSAP form a unique identifier for the local connection endpoint.

cesLocalVci

This object identifies the internal VCI assigned to a local endpoint, by the switch. The cesLocalVpi, cesLocalVci and cesLocalNSAP form a unique identifier for the local connection endpoint.

cesLocalNSAP

This object identifies the internal NSAP address assigned to local endpoint. The NSAP address is 20 bytes long and follows the format: - 13 bytes as prefix 2 bytes for Cisco ID, - 2 bytes for Cisco ID - 1 byte reserved - 3 bytes for logical interface (slo ...

cesRemoteVpi

This object identifies the VPI value of the peer endpoint. The cesRemoteVpi, cesRemoteVci and the cesRemoteNSAP identify the peer endpoint(remote) in the networking domain. The value should be 0 for a DAX connection within the switch. This object can be s ...

cesRemoteVci

This object identifies the VCI value of the peer endpoint. The cesRemoteVpi, cesRemoteVci and the cesRemoteNSAP identify the peer endpoint(remote) in the networking domain. The value should be 0 for a DACS connection within the switch. This object can be ...

cesRemoteNSAP

This object identifies the NSAP address of the peer endpoint. The NSAP address is 20 bytes long and follows the format: - 13 bytes as prefix 2 bytes for Cisco ID, - 2 bytes for Cisco ID - 1 byte reserved - 3 bytes for logical interface (slot:1 bytes,port ...

cesMastership

This is used by PXM to determine if this end point is master or slave, a new type unknown(3) is added to identify the SM in MGX8220(formerly AXIS) shelf and the SM in MGX8250 shelf. In MGX8220 shelf, user can create endpoints without specifying X/Y/P para ...

cesVpcFlag

This represents the connection type, used for PXM to identify VPC/VCC but CESM card doesn't use it always set to vcc for CESM card.

cesConnServiceType

This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Not used 4 ==> Unspecified Bit Rate 5 ==> ATM frame relay 6 ==> standard ABR 7 ==> foresight ABR Note that the value of this object is used by PXM card. The default valu ...

cesRoutingPriority

This is used by PXM to determine how important this connection is when selecting connections to route.

cesMaxCost

This object is used by the networking entity to select a route based on administrative weight of possible routes. It is related to Cost Based Routing. This is used by PXM so that it won't choose a path with a cost greater than this configured level. This ...

cesRestrictTrunkType

Restricted trunk type for routing, used by PXM. It specifies that the connection either cannot be routed over satelite trunks, or terrestrial trunks, or it can be on any type of trunk. It is not necessary to be provide in the connection setup request, the ...

cesConnPCR

This object identifies the Peak Cell Rate(PCR) value. If not provided during the row creation, the value will be computed as follows, For CESM-8T1/E1 - N * 64 Kbps , where N = Number of timeslots assigned to this channel. For CESM-T3, the value is 44736 ...

cesConnMCR

This object identifies the Minimum Cell Rate(MCR) value. If not provided during the row creation, the value will be computed as follows, For CESM-8T1/E1 - N * 64 Kbps , where N = Number of timeslots assigned to this channel. For CESM-T3, the value is 447 ...

cesConnPercentUtil

This is the expected long-term utilization of the channel by theis end-point. For CESM-8T1/E1/T3/E3 , the value is 100%

cesmConnRemotePCR

The PCR value of the remote end. If not set, the value for this object is derived from the end point parameter.

cesmConnRemoteMCR

The MCR value of the remote end. If not set, the value for this object is derived from the end point parameter.

cesmConnRemotePercentUtil

This is the expected long-term utilization of the channel by the other end-point.

cesmConnForeSightEnable

This object is used by the controller(PAR/PNNI/TAG) to set up the Qbin for the connection. This is notapplicable to CESM-8T1/E1/T3/E3.

cesmConnFGCRAEnable

enables/disables Frame based GCRA (early packet discard). This is not applicable to CESM-8T1/E1/T3/E3.

cesmChanReroute

This is used by the administrator to trigger the re-routing of the connection. The rerouting takes effect, when this object is set to true(1). When set to false (2), no action is taken. A get on this object always returns false (2). This object is not app ...

cesmChanPrefRouteId

This object serves to to associate a preferred route with a connection. The value '0' means no preferred route is associated with this connection. Usage: - If the value of this set to 0, the object cesmChanDirectRoute is automatically set to FALSE by the ...

cesmChanNumNextAvailable

This variable contains the next unused channel number of the possible 248. This number can be used in channel config table. cesChanNumNextAvailable gets updated whenever this number is used to create a new logical channel. Value 0 for this variable indica ...

cesmEndPtMapGrpEntry

An entry for cesmEndPtMapGrpEntry.

cesEndPortNum

This object identifies the CES logical port. The value for this object must be same as 'cesPortNum' object from cesmPortCnfGrpTable.

cesEndChanNum

This object identifies the CES connection number. The value of this object is same as the value of 'cesCnfChanNum' object in cesmChanCnfGrpTable.

cesEndLineNum

This object identifies the physical line on which connection is provisioned. The value in this object object must match with the value specified in 'cesPortLineNum' for a given logical port(cesEndPortNum).

ciscoWanCesConnGroup

A collection of objects providing information applicable to CES Connections.

ciscoWanCesConnEndptGroup

A collection of objects related to End Point mapping in circuit emulation connections.

ciscoWanCesConnGeneralGroup

A collection of objects related to next available channeli number and next available VPI value of connections supported.