CISCO-WAN-CES-PORT-MIB Download

cesmPortCnfGrpTable

The config table is for CES logical port. This is used for configuring the port type and number of DS0s and number of Subcircuits in DS0 on the CES port.

cesmPortCnfGrpEntry

An entry for each logical port. Each entry contains information on the port type, DS0s configured and number of DS0 subcircuits.

cesPortNum

This object identifies the logical port number. The range support depends upon the type of the service module(Card). - 8 port T1 Card, range is 1..192. - 8 port E1 Card, range is 1..248. - 1 port T3 Card, range is 1..1. Range is caclulated as follows. Thi ...

cesPortRowStatus

This variable enables or modifies the port 1 - add : Add a logical port 2 - del : Delete a logical port 3 - mod : Modify a logical port.

cesPortLineNum

This object represents the line number to which this port is associated. The supported range depends upon the type of service module(card).

cesPortType

This object represents port type whether it is carrying subrate circuits. structured : This is for SDT(Structured Data Transfer). This type of port supports following features: * intended to emulate point-to-point fractional DS1 or E1 circuit. * Sync ...

cesPortDs0ConfigBitMap

This represents bit map of DS0s for a line which are used to form this logical port. Bit 0 represents DS0-1.

cesPortNumOfDs0Slot

This represents number of DS0 time slots configured to this Port. If the cesPortType is strau(4), then this can not have more than 1 DS0 time slot.

cesPortNumOfSCIPerDS0

This object represents number of subcircuit in the DS0 time slot. This is applicable only when cesPortType is strau(4). 8 = there are 8 no .of 8kbps links (1 bit) 4 = there are 4 no .of 16kbps links (2 bit) 2 = there are 2 no .of 32kbps links (4 bit) Cu ...

cesPortSpeed

This object identifies the configured speed of port. Max speed for T1 = 1544 Max speed for E1 = 2038 Max speed for T3 = 44736 Max speed for E3 = 34368.

cesPortState

This variable indicates the state of the logical port. The possible values are : notConfigured (1) : Port is not configured active (2) : Port is in active state remoteLoopback (3) : Remote Loopback is set failedDueToLine(4) : Port failed due to s ...

cesPortBERTEnable

This variable enables/disables BERT. This object is not supported in CESM-T3E3.

cesPortNextAvailable

This variable contains the next UNUSED logical port number of the possible 32 DS0s * n ports. This number can be used in channel config table, the cesportNextAvailable gets updated if the number gets used to create a logical port. A '0' indicates that no ...

cesPortsUsedLine1

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 1

cesPortsUsedLine2

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 2.

cesPortsUsedLine3

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 3

cesPortsUsedLine4

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1. This is for line 4

cesPortsUsedLine5

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 5

cesPortsUsedLine6

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 6

cesPortsUsedLine7

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 7

cesPortsUsedLine8

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1 This is for line 8

ciscoWanCesPortsUsedGroup

The collection of objects which are applicable for general information about logical ports.

ciscoWanCesPortConfGroup

The collection of objects which are used to represent Circuit Emulation Service Port information.

ciscoWanCesPortDs0InDs1Group

The collection of objects related to information on DS0 time slots used in each DS1 line.