CISCO-WAN-FR-CONN-MIB Download

frChanCnfGrpTable

This table is for configuring connection parameters for frame relay connections.

frChanCnfGrpEntry

An entry for each frame relay connection.

chanNum

The value of this object identifies the frame relay connection/channel index. Note that the actual range of the index supported by a card depends on the type of card. Supported Range for different Card Types: FRSM-4T1/E1 : Range is 16..271 (256 en ...

chanRowStatus

This object is used for adding/modifying/deleting the channel. add(1) : For adding the frame relay connections. delete(2): For deleting frame relay connections. mod(3) : For Modifying frame relay connections. This is also used for uping the connection ...

chanPortNum

This object refers to the frame relay port on which channel is created. This is a mandatory object for creating the channel. For FRSM12 Card: This object contains the port's ifIndex value. ::= { frChanCnfGrpEntry 3 } SYNTAX Integer32 (0..8388607) MAX-ACCE ...

ibs

The value of this object is euqal to the excess burst size(Be) parameter for this PVC endpoint. The value of ibs should be less or equal to bc when cir is greater than 0. The value of ibs has to be 0 when cir is 0. The peak value for ibs in FRSM-VHS cards ...

mir

The value of this object is euqal to the minimum information rate for Foresight. The unit is 1 Cell/Sec = 16 fastpackets/sec. is equal to 16 fastpackets/sec. Following information about cps is for reference only: The peak value for qir in FRSM-VHS cards i ...

chanFECNconfig

The value of this object specifies how to map from FECN field in the frame Relay PDU to the EFCI field in the ATM cells. This object does not apply to NIW. This is applicable only for SIW. mapEFCI(1) : Maps the FECN bits in frame-relay to EFCI bit in th ...

chanDEtoCLPmap

The value of this object specifies how to map from DE bit on the Frame Relay side to CLP bit on the ATM side. mapCLP(1) : Map DE bit to CLP bit in ATM cell. setCLPzero(2) : Ignore DE bit. Set CLP to 0. setCLPone(3) : Ignore DE bit. Set CLP to 1. For ...

chanCLPtoDEmap

The value of this object enables mapping of Cell Loss Priority(CLP) bit on the ATM Side to Discard Eligibility(DE) bit on the Frame relay side. The possible values are : mapDE(1) : Map CLP bit to DE bit. Valid for SIW and NIW. setDEzero(2) : Ignore ...

chanIngrPercentUtil

The ingress utilization on a frame relay connection.

chanEgrPercentUtil

The egress utilization on a frame relay connection.

chanEgrSrvRate

The value of this object identifies egress CIR value for a frame relay connection. The value of this object must be less than or equal(<=) to the port speed. The value supported depends upon the interface and service module(card) type. For E1 Service Modu ...

chanFrConnType

The value of this object is used for configuring connection type of a frame relay connection. The possible values are : pvc(1) : Permanent Virtual Connection svc(2) : Switched Virtual Connection spvc(3) : Soft PVC. par(4) : Portable Auto Route Conn ...

frCDRNumber

The value of this object identifies the CDR(Call Detail Record) number. This is the key to correlate cell/frame counts, start/end record. For FRSM12 Card: Not Supported ::= { frChanCnfGrpEntry 34 } SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS ...

frLocalVci

The value of this object provides the VCI value for the local endpoint. This object in conjunction with frLocalVpi and frLocalNSAP represents the local end point of this connection. The service module assigns this value specified in object 'dLCI'.

frLocalNSAP

The value of this object identifies the NSAP address of the frame relay connection. The value of this object follows the format: Prefix : 13 Bytes Cisco ID : 2 bytes Reserved : 1 byte Slot Number : 1 byte Port Number : 2 bytes ESL ...

frRemoteVci

The value of this object identifies the VCI value of remote end point of this connection. The frRemoteVpi, frRemoteVci and frRemoteNSAP identifies the remote end point of this connection.

frRemoteNSAP

The value of this object identifies the NSAP address of the frame relay connection. The value of this object follows the format: Prefix : 13 Bytes Cisco ID : 2 bytes Reserved : 1 byte Slot Number : 1 byte Port Number : 2 bytes ESL ...

frMastership

This is used by PXM to determine if this end point is master or slave, a new type unknown is added to identify the SM in MGX8220 shelf and the SM in MGX shelf. In AXIS shelf, user can still use addchan to add a channel without specifying X/Y/P parameters. ...

frConnServiceType

This specifies the service type 1 ==> Constant Bit Rate 2 ==> Variable Bit Rate 3 ==> Not used 4 ==> Unspecified Bit Rate 5 ==> ATM frame relay 6 ==> standard ABR 7 ==> foresight ABR Note that this is used by PXM card, SV+ doesn't need to set it, if not s ...

frConnForeSightEnable

This object is used by the controller(PAR/PNNI/TAG) to set up the Qbin for the connection, if this is not set, it'll be defaulted by SM to the same as foreSightEnable in the end point parameters. For FRSM12 Card: Not Supported.

frConnFGCRAEnable

The value of this object is used for enabling/disabling Frame based GCRA (early packet discard). For FRSM12 Card: Not Supported.

chanServType

The value of this object indicates the indicates the class of the connection. 1-High priority (typically CBR connections) 2- real-time VBR 3- non-real time VBR 4- Available Bit Rate 5- Unspecified Bit Rate 9- Standard ABR There are 8 queues actually but o ...

chanServiceRateOverride

This variable sets the SAR IR programming option. Foresight and chanServiceRateOverride are mutually exclusive. For FRSM12 Card: Not Supported.

chanServiceRate

This is the rate to which IR can be set to when chanServiceRateOverride is set to enable(1). If chanServiceRateOverride is disable(2) then this object does not have any significance. For FRSM-8T1/8E1,this is defined in fastpackets/sec. For FRSM-VHS, this ...

zeroCirConEir

The value of this object defines defines EIR value for '0' CIR connection. If the value is '0', EIR is set to port speed. If zeroCirConEir is non-zero value, EIR is set to value of this object, and this value is used for policing in ingress direction. Thi ...

chanReroute

This is used by the administrator to trigger the re-routing of the connection. The rerouting takes effect, when this object is set to true(1). When set to false (2), no action is taken. A get on this object always returns false (2). This object is not app ...

frConnRemoteSCR

Sustained cell rate of the other end, Used for VBR connections setup with PNNI controller. For FRSM12 Card: Default value is frConnSCR This object is not applicable to MGX Release 1.x ::= { frChanCnfGrpEntry 61 } SYNTAX Integer32 (1..17) MAX-ACCESS r ...

frChanCnfChangeCount

This object is added only for FRSM12 card. This counter tracks the number of configuration changes that happen on a channel. The counter is associated only with the end point and NOT with the connection itself. This counter is used by the NMS to determi ...

frChanCnfIgnoreIncomingDE

This object is added for FRSM12 card. When this object is enabled, the incoming frames with DE(Discard Eligible) bit set to 1 are counted in the Bc bucket instead of Be bucket This object is not applicable to MGX Release 1.x.

frChanOamCCEnable

This object is added for FRSM12 card. This object serves to enable or disable continuity check(CC) on a connection endpoint. When continuity check is enabled on an endpoint, the endpoint anticipates OAM CC cells from its peer endpoint. OAM CC cells are se ...

frChanStatsEnable

This object serves the purpose of enabling/disabling statistics collection on a per connection basis. In implementations which do not have such limitations, this object can be set to enable(1) for all connections. Limits imposed by software or hardware im ...

frChanLocalLpbkEnable

This object is added for FRSM12 card. This object when enabled adds a channel-level loopback towards the port side. If the connection is in loopback, Connection MIB (FrChanCnfGrpEntry) variables cannot be modified. This object is not applicable to MGX Re ...

frConnRemoteMBS

Remote Maximum Burst Size in terms of number of cells. This object should be set by the user in cases when the remote end of the connection is an ATM end-point where the Local MBS can be explicitly specified. In such cases, this element should be set to b ...

frChanDirectRoute

This object serves to associate a prefer route as directed route (correspond to the prefer route object frChanPrefRouteId). A directed route specifies that the associated preferred route is the only permission route for the connection to take. Should the ...

chanNumNextAvailable

This variable contains the next UNUSED channel number of the maximum possible value(depends upon the service module). This number can be used in channel config table, the ChanNumNextAvailable gets updated if the number gets used to create a logical channe ...

frstdABRCnfGrpTable

This table is used for configuring ABR parameters on a frame relay connection. ::= { frChanCnfGrp 3 } SYNTAX FrstdABRCnfGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry in ABR Configuration table.

frstdABRcnfChanNum

Refers to the virtual connection index. The value supported depends upon the type of service module. Supported Range for different Card Types: FRSM-4T1/E1 : supported range is 16..271 (256 entries) FRSM-8T1/E1 : supported range is 16..1015 ( ...

frstdABRFRTT

The value of this object is equal to Fixed Round-Trip Time(FRTT). The FRTT is sum of the fixed propogation delays from the source to a destination network. The Value 0 signifies that FRTT is not available.

frstdABRRDF

The value of this object is equal to Rate Decrease Factor(RDF). The RDF controls the rate decrease which occurs when backward RM-cells with CI=1 are received. Larger values lead to faster rate decrease. The value specified has to be inverted to arrive at ...

frstdABRRIF

The value of this object is equal to Rate Increase Factor(RIF). The RIF controls the rate increase which occurs when a backward RM-cell is received with CI=0 and NI=0. The value specified has to be inverted to arrive at the actual value. The valid values ...

frstdABRNrm

The value of this object is equal to number of cells a source may send for each forward RM cell. The valid values possible are only powers of 2 starting from 2; i.e. 2, 4, 8 ..... 256. The SNMP agent has to verify this compliance.

frstdABRTrm

The value of this object is equal to Upper bound on the time between forward RM cells for an active source.

frstdABRCDF

The value of this object is equal to Cutoff Decrease Factor(CDF). The value specified has to be inverted to arrive at the actual value. The valid values possible are 0 and only powers of 2; i.e., 1, 2, 4, 8, 16, 32, 64. The SNMP agent has to verify this c ...

frstdABRADTF

The value of this object is equal to ACR Decrease Time Factor(ADTF). The Granularity allowed is 10 milli seconds. i.e. 10,20,30 etc. The SNMP agent has to verify this compliance.

frstdABRICR

The value of this object is equal to Initial Cell Rate(ICR). The ICR is the rate at which the source should send initially and after an idle period. This includes the bandwidth allocated for both data cells as well as all in-rate RM cells.

frstdABRMCR

The value of this object is equal to Minimum Cell Rate(MCR). The MCR is the rate at which the source is allowed to send. This includes the bandwidth allocated for both data cells as well as all in-rate RM cells.

frstdABRPCR

The value of this object is equal to Peak Cell Rate(PCR). The PCR is the rate at which the source is allowed to send. This includes the bandwidth allocated for both data cells as well as all in-rate RM cells.

frChanStateGrpTable

Table of transmit/receive states of channels.

frChanStateGrpEntry

An entry for FrChannelStateGrpEntry.

stateChanNum

The value of this object refers to frame relay connection. The value must be same as the value of the object 'chanNum' in frChanCnfGrpTable.

chanState

This variable indicates the LMI state of the VC (channel). The possible values are : notConfigured(1): Connection Not configured okay(2) : Connection is in Ok state alarm(3) : Connection is in alarm failed(4) : Connection is in failed ...

xmtAbitState

The value of this object identifies the A bit transmit state. The possible values are : off(1) : LMI is off sendingAequal1(2) : LMI is on and connection is O.K. sendingAequal0(3) : LMI is on and connection is failed.

rcvAbitState

The value of this object identifies the A bit receive state. The possible values are : off(1) : LMI is off rcvingAequal1(2) : LMI is on and connection is O.K. rcvingAequal0(3) : LMI is on and connection is failed.

xmtATMState

This variable indicates the transmit state of the VC (channel) on the ATM side. The possible values are : notSending(1) : Not sending any state sendingAIS(2) : Sending AIS OAM state sendingFERF(2) : Sending FERF OAM state.

rcvATMState

This variable indicates the receive state of the VC (channel) on the ATM side. The possible values are : notRcving(1) : Not receiving any state rcvingAIS(2) : Receiving AIS OAM rcvingFERF(2) : Receiving FERF OAM.

chanStatusBitMap

This variable indicates the consolidated bit map of the channel alarm state. Individual bit positions are as defined below. Bit position Fail/Alarm Reason ------------ ---------- ------ 0 Alarm Reserved 1 Alarm ...

frEndPtMapGrpEntry

An entry in the frame relay connection Endpoint table.

endPortNum

This object identifies the frame relay logical port. The value for this object must be same as 'portNum' object in frPortCnfPortGrpTable. If ifTable is is implemented in a service module, this object must be same as the ifIndex of frame relay port.

endDLCI

The value of this object is equal to the DLCI value for this PVC endpoint.

endChanNum

The value of this object identifies the frame relay connection number. The value of this object is same as the value of 'chanNum' object in frChanCnfGrpTable. This object contains value 0, if port.dlci is a multicast group.

endLineNum

The value of this object is equal to the physical line(for example T1/E1) or ifIndex on which connection is provisioned. If ifTable is not implemented in a service module, then the range is from 1 to Maximum number of lines supported. If ifTable is is imp ...

ciscoWanFrConnGroup

A collection of objects providing information applicable to a Frame Relay Connection.

ciscoWanFrConnForesightGroup

A collection of objects related to foresight feature of a frame realay connection.

ciscoWanFrConnQueueGroup

A collection of objects related to queue depth egress/ingress thresholds.

ciscoWanFrConnTestGroup

A collection of objects related to testing Frame relay connections.

ciscoWanFrConnStateGroup

A collection of objects related to state of Frame Relay connections.

ciscoWanFrConnEndptGroup

A collection of objects related to Endpoint mapping in Frame Relay Connections.

ciscoWanFrConnABRGroup

A collection of objects related to ABR in a frame relay connection.