CISCO-WAN-TOPOLOGY-MIB B Download

cwtGatewayAdminStatus

The value of this object determines whether this node is a Gateway Node or not. A value of `enable' configures this node to be the Gateway Node, and enables the generation of the topology database. A value of `disable' configures this node to not be a Gat ...

cwtGatewayNodeOperStatus

This is the operational status of the Gateway Node. 'disabled' indicates that this node is not a Gateway Node and no topology database is available on this node. 'enabled' indicates that this node has been configured as the Gateway Node and the topology d ...

cwtDBLastChange

The value of MIB II's sysUpTime object at the time that: a) the topology database is last changed on this node. b) the cwtGatewayAdminStatus is last changed. c) the cwtGatewayNodeOperStatus enters the 'enabledAndFull' state.

cwtNodeInfoTable

A table of node topology information is to be maintained for the management station. This table contains the information for the nodes in the peer group.

cwtNodeInfoEntry

This is a row entry in the topology node info table. Each entry corresponds to one node in the network.

cwtIndex

This is the index into the topology database array. This value should remain persistent while the topology database exists, which means that it'll be consistent across boots. However, if this node is disabled as the gateway node, and later on enabled (by ...

cwtGatewayNodeFlag

This variable indicates if the corresponding entry is a Gateway Node or not. If this value contains 'true', the corresponding node is a Gateway Node. If this value contains 'false', then the corresponding node is not a Gateway Node.

cwtNodeId

The unique Id which identifies the node in the entry. This value is different from cwtIndex because it is a unique number which identifies a node in the ATM network, while cwtIndex is an index for an entry in the topology database. The same physical node ...

cwtNodeName

The configured name of the node.

cwtPrimIPIfType

This object specifies the type of interface for the associated instance of cwtPrimIP.

cwtPrimIPIfName

This object specifies the name of the interface for the associated instance of cwtPrimIP.

cwtPrimIPAddrType

This object specifies the type of address contained in the associated instance of cwtPrimIP.

cwtPrimIP

Primary IP address of the corresponding node. This value is taken from the PNNI Nodal PTSE. The primary IP address is used by the NMS to manage the switch. The type of interface (i.e. ATM interface, LAN interface, etc) for this IP address is specified ...

cwtSecIPIfType

This object specifies the type of interface for the associated instance of cwtSecIP.

cwtSecIPIfName

This object specifies the name of the interface for the associated instance of cwtSecIP.

cwtSecIPAddrType

This object specifies the type of address contained in the associated instance of cwtSecIP.

cwtSecIP

Secondary IP address of the corresponding node. This value is taken from the PNNI Nodal PTSE. This value is used by the NMS to manage the switch. Please refer to the Description section of cwtPrimIP for more information.

cwtSysObjId

This variable contains the sysObjectID of the node, which is used to identify different hardware platforms. The actual values are defined in CISCO-PRODUCTS-MIB.

cwtNodeInfoTimeOutFlag

This variable indicates if the PTSE of this node is currently contained in the PNNI PTSE database. The nodal information in the persistent topology database is derived from the PTSEs in the PNNI PTSE database. The entries in the PNNI PTSE database times o ...

cwtRowStatus

In our implementation, we'll be supporting 'active', 'createAndGo', and 'destroy'. The value of this variable is set to 'active' by the managed system for each valid entry. If a management station wants to delete an entry from the database, this value i ...

cwtFeederInfoTable

A table of 'feeder' information to be maintained for the management station. This table contains the information for the 'feeders' in this peer group.

cwtFeederInfoEntry

This is a row entry in the feeder info table. Each entry corresponds to one 'feeder' in the network.

cwtFeederIndex

This is the index into the feeder database array. This value should remain persistent while the feeder database exists, which means that it'll be consistent across boots. However, if this node is disabled as the gateway node, and later on enabled, then t ...

cwtLocalNodeId

The unique Id which identifies the node the feeder is attached to.

cwtLocalIfIndex

This variable contains the 'ifIndex' of the local port this feeder is connected to.

cwtLocalIfName

The textual name of the interface of the local port this feeder is connected to. This should contain the same 'ifName' associated with the 'cwtLocalIfIndex'. If this interface does not have a textual name, the value of this object is a zero length string.

cwtFeederShelf

This variable contains the physcial shelf number of the feeder module.

cwtFeederSlot

This variable contains the physical slot number of the feeder module.

cwtFeederPort

This variable contains the physical port number of the feeder module.

cwtFeederLMIType

This object identifies the 'link' type. feeder(1) is applicable when cwtFeederType contains a value other than fdrNON(12). xLMI(2) is applicable only when cwtFeederType contains a value of fdrNON(12). Both feeder(1) and xLMI(2) are CISCO proprietary inte ...

cwtFeederType

This identifies the feeder type. fdrNON(12) is applicable when cwfLMIType is xLMI(2). Other values are applicable when cwtFeederLMIType is feeder(1). The possible values are : fdrIPX -- Feeder is an IPX node in a routing network fdrBPX -- Feed ...

cwtFeederName

The configured name of the feeder.

cwtFeederLanIPAddrType

This object specifies the type of address contained in the associated instance of cwtFeederLanIP.

cwtFeederLanIP

This object specifies the LAN IP address of the 'feeder'. The type of this address is specified by cwtFeederLanIPAddrType.

cwtFeederAtmIPAddrType

This object specifies the type of address contained in the associated instance of cwtFeederAtmIP.

cwtFeederAtmIP

This object identifies the ATM IP address of the 'feeder'. The type of this address is specified by cwtFeederAtmIP.

cwtFeederModelNumber

This variable contains the 'model number' of the corresponding feeder. This is an implementation specific integer value which is used to differentiate between feeder platforms.

cwtFeederRowStatus

In our implementation, we'll be supporting 'active', and 'destroy'. The value of this variable is set to 'active' by the managed system for each valid entry. If a management station wants to delete an entry from the database, this value is set to 'destr ...

cwtLinkInfoTable

A table of 'link' information in the PNNI network. If a switch is managed by multiple network management stations, these network management stations can have a persistent view of links in the network by retrieving this table. A link is a PNNI link between ...

cwtLinkInfoEntry

This is an entry in the 'cwtLinkInfoTable'. Each entry corresponds to one link in the network. a) The entries in this table are derived from PNNI PTSE database or added by a network management station. b) The entries in the PNNI PTSE database time out whe ...

cwtLinkIndex

This is the index into the link database array. This value is of local significance to the gateway node. As long as a node remains 'enabled' as a gateway node, this value remains persistent across boots. However, if this node is disabled as the gateway n ...

cwtLinkLocalNodeId

The unique Id which identifies the local node this link resides on.

cwtLinkRemoteNodeId

The unique Id which identifies the remote node this link resides on.

cwtLinkLocalIfIndex

The local 'ifIndex' of this link.

cwtLinkRemoteIfIndex

The remote 'ifIndex' of this link.

cwtLinkLocalPhysicalId

The local physical port identifier of this link.

cwtLinkRemotePhysicalId

The remote physcial port identifier of this link.

cwtLinkInfoTimeOutFlag

This variable indicates if the PTSE of this link is currently contained in the PNNI PTSE database. If this entry is also contained in the PNNI PTSE database, the agent sets the value of this variable to 'true'. If this entry is not contained in the PNNI P ...

cwtLinkRowStatus

In our implementation, we'll be supporting 'active', 'createAndGo', and 'destroy'. The value of this variable is set to 'active' by the managed system for each valid entry. If a management station wants to delete an entry from the database, this value i ...

cwtSystemMIBGroups

This group contains the object which enables a node to function as a Gateway Node.

cwtNodalMIBGroups

This group contains objects which identify a node in the network.

cwtFeederMIBGroups

This group contains objects which identify a node in the network.

cwtLinkMIBGroups

This group contains objects which identify a link in the network.