CISCO-XGCP-EXT-MIB Download

cxeCallCtrlConfigTable

This table contains objects used for configuring general parameters in call control default to the local media gateway in xGCP protocols.

cxeCallCtrlConfigEntry

There is one entry for each media gateway. The entry will be automatically generated when a media gateway is detected.

cxeCallCtrlControlServiceType

This object identifies Type Of Service (TOS) field of IP header for the control packet in VoIP application.

cxeCallCtrlBearerServiceType

This object identifies Type Of Service (TOS) field of IP header for the voice payload packet in VoIP application.

cxeCallCtrlVoIpDtmfRelayMode

This object defines whether the DTMF (Dual Tone, Multi-Frequency) digits need to be transported to the other endpoint via NSE packets in Voice Over IP. The value of this object will be utilized when the call agent does not specify this parameter.

cxeCallCtrlVoIpDtmfCodec

This object identifies DTMF relay codec for VoIP. This object is not applicable if cxeCallCtrlVoIpDtmfRelay is DtmfRelayDisabled.

cxeCallCtrlVoAal2DtmfRelayMode

This object defines whether the DTMF (Dual Tone, Multi-Frequency) digits need to be transported to the other endpoint in Voice over AAL2 packets. The value of this object will be utilized when the call agent does not specify this parameter.

cxeCallCtrlVoAal2DtmfCodec

This object identifies DTMF relay CODEC for Voice over AAL2. This object is not applicable if cxeCallCtrlVoAal2DtmfRelay is DtmfRelayDisabled.

cxeCallCtrlTsePayload

This object identifies TSE (Telephony Signaling Events) payload type.

cxeCallCtrlNetNseTimer

This object identifies Network Signaling Event (NSE) timeout value.

cxeCallCtrlRtcpRcvTimer

This object identifies the number of times of Real Time Control Transport (RTCP) report interval if the media gateway has not recieved any RTCP packets from another side. The media gateway will mark another side inactive, or delete it if no RTCP packet ha ...

cxeCallCtrlIgnoreAal2LcoCodec

This object defines whether to ignore the AAL2 Local Connection Option (LCO) message from the call agent or not.

cxeCallCtrlDigitMapOrder

This object defines the type of digit map order. The MGC can advise and load the gateway with a digit map that correspond to the dial plan to collect the access codes, credit card numbers and other numbers requested by call control services.

cxeCallCtrlT38Inhibited

This object defines whether T.38 is inhibited in the media gateway or not. T.38 is a Fax Relay Protocol defined by ITU for real-time protocol for Fax over IP networks.

cxeCallCtrlT38NseRspTimer

This object defines a timeout value for a timer. This timer is started after sending a NSE 200 while waiting for the NSE 201 acknowledgement or NSE 202 negative acknowledgement. Expiration of the timer will indicate that the request for switch to T.38 has ...

cxeCallCtrlT38FecEnabled

This object is used to enable the Forward Error Correction (FEC) for UDP-based fax transport. This object is not applicable if cxeCallCtrlT38Inhibited is set to 'true'.

cxeCallCtrlT38LsRedundancy

This object determines the extent of the Internet Fax Protocol (IFP) packet transmission redundancy for the low-speed control information exchanged during the first phase of a T.38 fax relay connection. Depending on whether Forward Error Correction (FEC) ...

cxeCallCtrlT38HsRedundancy

This object determines the extent of the Internet Fax Protocol (IFP) packet transmission redundancy for the high-speed control and image information exchanged following the initial low-speed phase of a T.38 fax relay connection. Depending on whether forwa ...

cxeCallCtrlT38NsfCountryCode

This object specifies the country code for identifying the country where the media gateway with non-standard capabilities was manufactured. This object is not applicable if cxeCallCtrlT38Inhibited is set to 'true'.

cxeCallCtrlT38NsfVendorCode

Per its definition (ITU T.35), the Vendor Code (also called the Terminal Provider Code) in the Non-Standard Facilities (NSF) code is a two-byte field identifying the manufacturer of the media gateway with non-standard capabilities. This object is not appl ...

cxeCallCtrlVselDselFselSupport

This object is used to enable or disable VSEL, DSEL and FSEL support. VSEL: Voice codec, packet length and packet times Selection DSEL: Data codec, packet length and packet times Selection FSEL: Fax codec, packet length and packet times Selection If cxeCa ...

cxeCallCtrlDefaultBearTraffic

This object specifies the combination of the network type (IP/ATM), virtual circuit type (PVC/SVC) and ATM adaptation layer type (AAL1/AAL2/AAL5) for the connection used in transporting bearer traffic. ipPvcAal5 (1) - The bearer traffic is transported in ...

cxeCallCtrlLastFailedMgcAddrType

This object indicates the address type, either IPv4 or IPv6, of cxeCallCtrlLastFailedMgcAddress.

cxeCallCtrlLastFailedMgcAddress

This object indicates the address of MGC (Media Gateway Controller) with which the media gateway had tried to communicate lastly but failed.

cxeCallCtrlProfileTable

This table defines the call control profiles. A call control profile contains the call control information that a call agent uses to establish a call. In the call control profile, it has the following configurations: (1) The information of call agent, suc ...

cxeCallCtrlProfileEntry

Each entry describes an instance of a call control profile in the media gateway. When an entry of call control profile is added to the table, the following object must be provided: cxeCcProfileName - an unique string of profile name to identify the profil ...

cxeCcProfileIndex

This object uniquely identifies the call control profile.

cxeCcProfileName

A unique name for the profile. The name of the profile has to be unique among all entries of the table. This object is mandatory during the creation of the entry. This object can not be modified. If users want to modify the name of the call control profil ...

cxeCcProfileNumVifs

This object reprsents the total number of voice interface (DS0 group) associated with this call control profile. The value of '0' means there is no voice interfaces associated with the profile. Before the call control profile can be deleted, this object s ...

cxeCcProfileMgcGrpNum

This object indicates which MGC Redundant group number that the call control profile will be used. The value is the index to MGC Redundant Group Table (cMgcGrpParamTable). There are two conditions for associating a MGC group with a profile: 1. At least on ...

cxeCcProfileMgcAddrType

This object identifies the address type applicable to cxeCcProfileMgcAddress.

cxeCcProfileMgcAddress

This object specifies the address of Media Gateway Controller (MGC) configured in the profile. When cxeCcProfileMgcGrpNum is non-zero (which menas using MGC group), this object can not be set.

cxeCcProfileProtocolIdx

This object specifies the protocol that the media gateway should communicate with MGC during call setup. It is the index of the protocol table(cMediaGwProtocolTable). If cxeCcProfileMgcGrpNum is non-zero, the value of this object will be ignored. The prot ...

cxeCcProfileXgcpRetryMethod

This object specifies the command/response retry method when the media gateway communicates with the MGC in xGCP protocols.

cxeCcProfileRetryMax1

This object contains the suspicious error threshold for signaling messages.

cxeCcProfileDnsLookupMax1

This object enables/disables the Max1 Domain Name Server (DNS) query operation when Max1 expires. This object is used when a gateway-initiated message is not acknowledged by the MGC. If the object is 'true', a DNS query is performed to re-resolve MGC's do ...

cxeCcProfileRetryMax2

This object contains the disconnect error threshold for signaling messages.

cxeCcProfileDnsLookupMax2

This object enables/disables the Max2 Domain Name Server (DNS) query operation when Max2 expires. This object is used when a gateway-initiated message is not acknowledged by the MGC. If the object is 'true', a DNS query is performed to re-resolve MGC's do ...

cxeCcProfileMwiTimeout

The timeout value for the message waiting indicator tone. Message Waiting Indicator (MWI) tone is used with message waiting services, it indicates that the media gateway is ready to accept address information or other information from an access line.

cxeCcProfileTsmaxTimeout

The timeout value for retransmission removal. The gateway uses the value of this object to determine how long for the MGCP messages stored in the retransmission queue before they are discarded.

cxeCcProfileTdinitTimeout

The voice interface (DS0 group) becomes disconnected when the media gateway tries to communicate with the call agent and the retransmission procedure times out after retrying. The voice interface (DS0 group) in disconnected state starts the disconnected t ...

cxeCcProfileTdminTimeout

The DS0 group (voice interface) becomes disconnected when it tries to communicate with the call agent and the retransmission procedure times out after retrying. The DS0 group (voice interface ) in disconnected state starts the disconnected timer initialis ...

cxeCcProfileTdmaxTimeout

The maximum waiting delay (Tdmax) timeout value used by the media gateway to send the Restart In Progress with the restart method as RM:disconnected to the call agent when the voice interface associated ds0-group disconnection condition occurs. The DS0 gr ...

cxeCcProfileTcritTimeout

This object represents the timeout value for the critical timer. If used along with a digit map, the timer is started when the last digit is received. i.e and when no more digits are required for a digit map match. After this timer expires, the digit map ...

cxeCcProfileTparTimeout

This object represents the partial dial timeout and is used along with a digit map as the inter-digit timer. This object is used by call processing when it processes mid-call DTMF digit reporting. The timer is not started until the first digit is entered, ...

cxeCcProfileThistTimeout

The MGCP protocol is organized as set of transactions, each of which is composed of a command and a resonse. The MGCP messages, being carried over UDP, may be subject to losses. In the absence of a timely response, commands are repeated. The media gateway ...

cxeCcProfileRtTimeout

This object specifies time for which the local ring back tone (towards the TDM) will be generated unless interrupted (e.g., by the answer from the called party or a delete connection command from the Call Agent). The value of '0' indicates that the tone w ...

cxeCcProfileRbkTimeout

This object specifies time for which the remote ring back tone (towards the packet network) will be generated unless interrupted (e.g., by the answer from the called party or a delete connection command from the Call Agent). The value of '0' indicates tha ...

cxeCcProfileCgTimeout

This object specifies time for network congestion tone will be generated. The network congestion tone will be generated when the network resources or bandwidth exceed their threholds. The value of '0' indicates that the tone will be generated indefinitely ...

cxeCcProfileBzTimeout

This object specifies time for which the busy tone will be generated unless interrupted (e.g., by the hangup from the calling party). The value of '0' indicates that the tone will be generated indefinitely unless interrupted.

cxeCcProfileDlTimeout

This object specifies time for which the dial tone will be generated unless interrupted (e.g., by the first DTMF digit from the calling party). The value of '0' indicates that the tone will be generated indefinitely unless interrupted.

cxeCcProfileSlTimeout

This object specifies time for which the stutter dial tone or confirmation dial tone will be generated unless interrupted (e.g., by the first DTMF digit from the calling party). The value of '0' indicates that the tone will be generated indefinitely unles ...

cxeCcProfileRgTimeout

This object specifies time for which the ringing cadence will be generated towards the basic PBX unless interrupted (e.g., by the answer from the called party or a delete connection command from the Call Agent). This is also the time for which remote inba ...

cxeCcProfileRoTimeout

This object specifies time for which the reorder tone or fast busy tone will be generated unless interrupted (e.g., by the hangup from the called party). The value of '0' indicates that the cadence will be generated indefinitely unless interrupted.

cxeCcProfileCot1Timeout

This object specifies time for which the continuity test tone 1 will be generated unless interrupted. The value of '0' indicates that the cadence will be generated indefinitely unless interrupted.

cxeCcProfileCot2Timeout

This object specifies time for which the continuity test tone 2 will be generated unless interrupted. The value of '0' indicates that the cadence will be generated indefinitely unless interrupted.

cxeCcProfileRowStatus

This object is used by users for adding/deleting an entry from the table. The entry can't be deleted if the value of cxeCcProfileNumVifs is greater than zero or the value of cxeCcProfileMgcGrpNum is greater than zero.