Crossroads Download

fcConfigNodeName

Worldwide name of a collection of N_Ports that comprise a Node.

fcConfigNodeNumNPorts

Number of N_Ports that comprise the named Node.

fcConfigEnableReset

Toggle for software reset. True indicates that ressetting the product via SNMP is allowed. NOTE: each time the product is initialized this object is set to FALSE (i.e. it is not sticky).

fcConfigUseHardAddress

Toggle for address configuration. True indicates that configuration of the source ID is allowed. False indicates that the source ID may not be changed.

fcConfigSourceID

3 byte Source address. For arbitrated loop, this will be the Hard Assigned AL_PA (preceeded by 2 0 bytes). ex. 0.0.EF

fcConfigSCSIMode

Fibre Channel to SCSI mapping mode.

fcConfigTraceMask

Trace Level.

fcConfigReset

Reset the product. Setting this object to TRUE will re-start all the software (similar to powering the product off, then on). The reset will only take place if fcConfigResetEnable is also TRUE. NOTE: resetting the product will disconnect all current Fib ...

fcConfigCommit

Commit the configuration values to the flash memory.

fcConfigFirmwareRevLevel

Firmware revision level.

miSerialBaudRate

The baud rate for the serial interface.

miMACAddress

Physical address (MAC address).

miethernetIPAddr

The IP address for this device.

miethernetIPNetmask

Ethernet Net Mask.

miTrapIPAddr

The IP address used for sending traps. Typically this is the IP address of the machine which has a network management program and/or MIB browser.

miTrapEnable

Enable/Disable Traps. If TRUE, traps are sent to the specified Trap IP Address. If disabled, no traps will be sent to the SNMP manager.

miTrapPriority

The Trap Priority. All SNMP Events (traps) of this priority (or higher) will be sent to the specified Trap IP Address.

scsiConfigTable

A Table containing SCSI Configuration parameters.

scsiConfigEntry

An entry in the SCSI Configuration Table.

scsiConfigIndex

Index into the SCSI Configuration Table.

scsiConfigInitID

Initiator SCSI ID.

scsiConfigTargetIDAdd

Get will return a mask of SCSI target ID's. A mask has a bit set for each target ID which is in use. Example: Get returns 133 = 0x0085 = 0000 0000 1000 0101 indicating target ID's are 7, 2 and 0. Set allows you to set SCSI target ID's, by setting the ap ...

scsiConfigTargetIDRemove

Get will return a mask of SCSI target ID's. A mask has a bit set for each target ID which is in use. Example: Get returns 133 = 0x0085 = 0000 0000 1000 0101 indicating target ID's are 7, 2 and 0. Set allows you to remove SCSI target ID's, by setting the ...

fctoSCSIMapTable

A Table containing the Fibre Channel to SCSI Map.

fctoSCSIMapEntry

An entry in the Fibre Channel to SCSI Map Table.

fctoSCSIMapIndex

Index into the Fibre Channel to SCSI Map (FC LUN).

fctoSCSIbus

SCSI bus number.

fctoSCSItarget

SCSI ID.

fctoSCSILUN

SCSI LUN.

scsitoFCMappingTable

A Table containing information describing how SCSI channels are mapped to the Fibre Channel.

scsitoFCMapEntry

An entry in the SCSI to FC Mapping Table.

scsitoFCMapIndexBus

Index into the SCSItoFC Map. SCSI bus number.

scsitoFCMapIndexSCSIID

Index into the SCSItoFC Map. SCSI ID.

scsitoFCMapIndexLUN

Index into the SCSItoFC Map. SCSI LUN.

scsitoFCMapDestID

The Fibre Channel Node number for the destination.

scsitoFCMapLUNlo

SCSI LUN low bytes.

scsitoFCMapLUNhi

SCSI LUN high bytes.

fcNPortPhysTable

A Table containing N_Port physical characteristics and status.

fcNPortPhysEntry

An entry in the N_Port Physical Characteristics Table.

fcNPortPhysNPortIndex

A unique number that identifies an N_Port/NL_Port. This number ranges from 1 to the value of fcNodeNumNPorts and its value remains constant for the identified N_Port/NL_Port until the management agent of the Node is re-initialized.

fcNPortSpeed

The transmission rate, an FC-0 physical characteristic.

fcNPortMedia

Type of media, an FC-0 physical characteristics.

fcNPortTransmitterType

Type of transmitter, an FC-0 physical characteristics.

fcNPortDistance

The maximum distance, an FC-0 physical characteristics.

fcNPortLinkState

The state of the FC link. Pending indicates that the initialization is still pending. Failed indicates that link initialization has failed. Successful indicates that the FC Link has initialized successfully.

fcNPortRTTOV

Receiver_Transmitter timeout value, used by the receiver logic to detect Loss of Synchronization.

fcNPortTopologyModel

The topology model on the Link. The N_Port/NL_Port may be attached to a Fabric, or attached to another N_Port or to FC-AL (Arbitrated Loop). This value is only meaningful if the FC Link has initialized successfully. (i.e. fcNportLinkState = Successful)

scsiStatisticsTable

A Table containing SCSI Statistics.

scsiStatsEntry

An entry in the SCSI Statistics Table.

scsiStatsIndex

Index into the SCSI Statistics Table. The SCSI bus number.

scsiStatsIOs

The number of IOs on the SCSI bus.

scsiStatsDisconnects

The number of Disconnects on the SCSI bus.

scsiStatsAbortCount

The of SCSI bus termination messages (i.e. ABORT, ABORT TAG, CLEAR QUEUE, BUS DEVICE RESET) which have terminated I/O processes.

scsiStatsBusResets

The count of SCSI bus resets.

scsiCfgResetFlag

Toggle SCSI Reset Operation. TRUE indicates that the SCSI bus will be reset on boot.

scsiCfgDiscDelay

Initial Discovery Delay. The amount of time (in msec) the system will wait before beginning the SCSI Discovery process.

scsiProductDataTable

A Table containing SCSI Product Data.

scsiPDEntry

An entry in the SCSI Product Data Table.

scsiPDIndex

Index into the SCSI Product Data Table. The SCSI LUN.

scsiPDBus

SCSI Bus number. Always 0 if your unit only has one SCSI Bus.

scsiPDTarget

SCSI Target ID.

scsiPDLun

SCSI Target Lun.

scsiPDVendorID

Vendor ID.

scsiPDProductID

Product ID.

scsiPDRevLevel

Revision Level.

scsiPDDeviceCode

Device type code.

scsiPDQualifier

Device type qualifier.

scsiPDRemoveableMedia

Removeable Media.

scsiPDANSIVersion

Device type version.

scsiPDECMAVersion

Device type version.

scsiPDISOVersion

Device type version.

scsiPDRespFormat

Response Format.

scsiPDLength

Additional data length.

scsiPDSoftReset

Support for Soft reset.

scsiPDCommandQing

Support for Command Queuing.

scsiPDLinkedCommands

Support for Linked Commands.

scsiPDSyncTransfer

Support for Sync transfer.

scsiPD16Bit

16 bit wide SCSI support.

scsiPD32Bit

32 bit wide SCSI support.

scsiPDRelativeAddr

Support for Relative address.

fcNPortStatisticsTable

A table of NPort statistics.

fcNPSEntry

An entry in the NPort statistics table.

fcNPSIndex

A unique number that identifies an N_Port. This number ranges from 1 to the value of fcNodeNumNPorts and its value remains constant for the identified N_Port until the management agent of the Node is re-initialized.

fcNPSInDeviceDataSeqs

The number of Device Data sequences received by this N_Port/NL_Port.

fcNPSOutDeviceDataSeqs

The number of Device Data sequences transmitted by this N_Port/NL_Port.

fcNPSInLinkDataSeqs

The number of Link Data sequences received by this N_Port/NL_Port.

fcNPSOutLinkDataSeqs

The number of Link Data sequences transmitted by this N_Port/NL_Port.

fcNPSInPBSYFrames

The number of P_BSY frames received by this N_Port/NL_Port.

fcNPSOutPBSYFrames

The number of P_BSY frames transmitted by this N_Port/NL_Port.

fcNPSInFBSYFrames

The number of F_BSY frames received by this N_Port/NL_Port.

fcNPSInPRJTFrames

The number of P_RJT frames received by this N_Port/NL_Port.

fcNPSOutPRJTFrames

The number of P_RJT frames transmitted by this N_Port.

fcNPSLinkDown

Number of Link down conditions detected.

fcNPSInAborts

Number of ABTS frames received.

fcNPSOutAborts

Number of ABTS frames sent.

fcNPSLaserFaults

Number of laser faults.

fcNPSLOS

Number of times Loss of Signal was detected.

fcNPSSync

Number of times Loss of Sync. was detected.

fcNPSBadRXChars

Number of bad characters received.

fcNPSLinkFail

Number of Link Failure conditions.

fcNPSBadCRC

Number of frames received with a bad CRC.

fcNPSProtoErrors

Number of protocol errors detected.