DES6500-SWL2MGMT-MIB Download

swDevInfoTotalNumOfPort

The number of ports within this switch. This value is the sum of the ports within this switch.

swDevInfoNumOfPortInUse

The number of ports in this switch connected to the segment or the end stations.

swDevInfoBootPromVersion

Boot Prom Version.

swDevInfoFirmwareVersion

Firmware Version.

swDevInfoHardwareVersion

Hardware Version.

swL2DevCtrlStpState

This object can be enabled or disabled spanning tree algorithm during runtime of the system.

swL2DevCtrlIGMPSnooping

This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.

swL2DevCtrlIGMPSnoopingMcstRTOnly

swL2DevCtrlRmonState

This object can be enabled or disabled RMON.

swL2DevCtrlCleanAllStatisticCounter

As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.

swL2DevCtrlVlanIdOfFDBTbl

Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is DEFAULT_VLAN_ID of system .

swL2MACNotifyState

-- "This object can enabled or disabled MAC Notification. -- "This object indicates the history size of variation MAC in address table. -- The default value is 1 . -- "This object indicates the time interval in second for ...

swL2DevCtrlWebTcpPort

This object can designate tcp port. When web disable this object can't accessible.

swL2DevCtrlTelnetState

This object control telnet status.

swL2DevCtrlTelnetTcpPort

This object can designate tcp port. When telnet disable this object can't accessible.

swL2DevAlarmTopologyChange

This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or f ...

swL2DevAlarmLinkChange

This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other.

swL2PortInfoTable

A table that contains information about every port.

swL2PortInfoEntry

A list of information for each port of the device.

swL2PortInfoPortIndex

This object indicates the module's port number.(1..Max port number in the module)

swL2PortInfoPortNumber

This object indicates the module's port number.

swL2PortInfoUnitID

Indicates ID of the unit in the system

swL2PortInfoType

This object indicates the connector type of this port.

swL2PortInfoLinkStatus

This object indicates the port link status.

swL2PortInfoNwayStatus

This object indicates the port speed and duplex mode.

swL2PortCtrlTable

A table that contains control information about every port.

swL2PortCtrlEntry

A list of control information for each port of the device.

swL2PortCtrlPortIndex

This object indicates the module's port number.(1..Max port number in the module)

swL2PortCtrlUnitIndex

Indicates ID of the unit in the device

swL2PortCtrlAdminState

This object decide the port enabled or disabled.

swL2PortCtrlNwayState

Chose the port speed, duplex mode, and N-Way function mode.

swL2PortCtrlFlowCtrlState

The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.

swL2PortCtrlLockState

This object decide the port is locked or not.

swL2PortCtrlMACNotifyState

-- "This object set each poet MAC notification state. -- "This object decide the multicast packets filtering mode on this port . This object configure the switch's jumbo frame settings.

swL2QOSBandwidthControlTable

.

swL2QOSBandwidthControlEntry

A list of information contained in swL2QOSBandwidthControlTable.

swL2QOSBandwidthPortIndex

Indicates the port .

swL2QOSBandwidthRxRate

Indicates RX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit.

swL2QOSBandwidthTxRate

Indicates TX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit.

swL2QOSSchedulingTable

.

swL2QOSSchedulingEntry

A list of information contained in swL2QOSSchedulingTable.

swL2QOSSchedulingClassIndex

Indicates the hardware queue number.

swL2QOSSchedulingMaxPkts

Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 15 can be specified.

swL2QOSSchedulingMechanism

Indicates the mechanism of QOS scheduling.

swL2QOS8021pUserPriorityTable

.

swL2QOS8021pUserPriorityEntry

A list of information contained in swL2QOS8021pUserPriorityTable.

swL2QOS8021pUserPriorityIndex

The 802.1p user priority .

swL2QOS8021pUserPriorityClass

The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).

swL2QOS8021pDefaultPriorityTable

.

swL2QOS8021pDefaultPriorityEntry

A list of information contained in swL2QOS8021pDefaultPriorityTable.

swL2QOS8021pDefaultPriorityIndex

Indicates the port number .

swL2QOS8021pDefaultPriority

The priority value to assign to untagged packets received by the switch ports on the switch..

swL2QOSSchedulingMechanismCtrl

This object can control QOS scheduling Mechanism.

swL2QOSHolPreventionCtrl

Control QOS Hol Prevention

swL2PortSecurityControlTable

port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this ...

swL2PortSecurityControlEntry

A list of information contained in swL2PortSecurityControlTable.

swL2PortSecurityPortIndex

Indicates the secured port to lock address learning.

swL2PortSecurityMaxLernAddr

Indicates allowable number of addresses to be learned at this port.

swL2PortSecurityMode

Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged out, the number of address can be learned has to be increased by one. In delet ...

swL2PortSecurityAdmState

Indicates administration state of locking address.

swL2PortSecurityDelVlanName

Indicates vlan name.

swL2PortSecurityDelPort

Indicates the port.

swL2PortSecurityDelMacAddress

Specifies MAC address.

swL2PortSecurityDelActivity

.

swL2TrunkMaxSupportedEntries

Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).

swL2TrunkCurrentNumEntries

Current actived number of entries in the trunk configuration table.

swL2TrunkCtrlTable

This table specifys which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkCtrlEntry

A list of information specifies which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkIndex

The index of logical port trunk. The trunk group number depend on the existence of unit and module.

swL2TrunkName

The name of logical port trunk.

swL2TrunkMasterPort

The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disable ...

swL2TrunkMember

Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 8 for one trunks.

swL2TrunkFloodingPort

The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.

swL2TrunkType

This object indicated that type of the trunk group. static : is static trunk group lacp : is LACP trunk group .

swL2TrunkState

This object indicates the status of this entry.

swL2TrunkAlgorithm

This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.

swL2TrunkLACPPortTable

This table specifys which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkLACPPortEntry

A list of information specifies which ports group a set of ports(up to 8) into a single logical link.

swL2TrunkLACPPortIndex

The index of logical port lacp.

swL2TrunkLACPPortState

The state of logical port lacp.

swL2MirrorLogicTargetPort

This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.

swL2MirrorPortSourceIngress

The represent the ingress into the source port packet to sniffed.

swL2MirrorPortSourceEgress

The represent the egress from the source port packet to sniffed.

swL2MirrorPortState

This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - writing this value to the object, and then the corres ...

swL2IGMPSnoopingMaxSupportedVlans

Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPSnoopingCtrlTable).

swL2IGMPSnoopingMaxIpGroupNumPerVlan

Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPSnoopingQueryInfoTable).

swL2IGMPSnoopingCtrlEntry

The entry in IGMP control table (swL2IGMPSnoopingCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.

swL2IGMPSnoopingQueryInterval

The frequency at which IGMP Host-Query packets are transmitted on this switch.

swL2IGMPSnoopingMaxResponseTime

The maximum query response time on this switch.

swL2IGMPSnoopingRobustness

The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.

swL2IGMPSnoopingLastMemberQueryInterval

The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.

swL2IGMPSnoopingHostTimeout

The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.

swL2IGMPSnoopingRouteTimeout

The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.

swL2IGMPSnoopingLeaveTimer

When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.

swL2IGMPSnoopingQueryState

This object decide the IGMP query enabled or disabled.

swL2IGMPSnoopingCurrentState

This object indicates the current IGMP query state.

swL2IGMPSnoopingCtrlState

This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - ...

swL2IGMPSnoopingQueryInfoTable

The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.

swL2IGMPSnoopingQueryInfoEntry

Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPSnoopingCtrState of associated VLAN entry are all enabled.

swL2IGMPSnoopingInfoQueryCount

This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.

swL2IGMPSnoopingInfoTxQueryCount

This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.

swL2IGMPSnoopingInfoTable

The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, ...

swL2IGMPSnoopingInfoEntry

Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnoopingSnooping and swL2IGMPSnoopingCtrlState of associated VLAN entry are all enabled.

swL2IGMPSnoopingVid

This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.

swL2IGMPSnoopingGroupIpAddr

This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.

swL2IGMPSnoopingMacAddr

This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.

swL2IGMPSnoopingPortMap

This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit re ...

swL2IGMPSnoopingIpGroupReportCount

This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.

swL2TrafficCtrlTable

This table specifys the storm traffic control configuration.

swL2TrafficCtrlEntry

A list of information specifies the storm traffic control configuration.

swL2TrafficCtrlGroupIndex

The index of logical port trunk. The trunk group number depend on the existence of unit and module.

swL2TrafficCtrlUnitIndex

Indicates ID of the unit in the device

swL2TrafficCtrlBMStromthreshold

This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl, swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlDlfStromCtrl objects whether is enabled) will active storm control. Whenever a port re ...

swL2TrafficCtrlBcastStromCtrl

This object indicates broadcast storm control function is enabled or disabled.

swL2TrafficCtrlMcastStromCtrl

This object indicates multicast storm control function is enabled or disabled.

swL2TrafficCtrlDlfStromCtrl

This object indicates destination lookup fail function is enabled or disabled.

swL2TrafficSegTable

This table specifys the port just can forward traffic to the specific port list.

swL2TrafficSegEntry

A list of information specifies the port with its traffic forward list.

swL2TrafficSegPort

The port number of the logical port.

swL2TrafficSegForwardPorts

The port list that the specific port can forward traffic.