EICON-DIALER-MIB Download

MIBs list

IPHost Network Monitor offer an easy way of SNMP monitoring your Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for EICON-DIALER-MIB

dialerInfoTable: General Information Table for dailer.
dialerInfoEntry: The set of dialer configuration attributes for one port.
dialerInfoPortRef: The id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.
dialerInfoType: Type of interface connecting the gateway to local or remote host computers.
dialerInfoTimeStart: The time elapsed since the dialer was statrted.
dialerInfoTimeConnect: The time elapsed since the dialer established the current connection.
dialerInfoLineSpeed: The speed setting of the driver (line speed), or the dialer (modem speed).
dialerInfoDataEncoding: The type of data encoding used on the connection.
dialerInfoClockType: The type of clocking used by the modem.
dialerDirectInfoTable: General Information Table for Direct dialer.
dialerDirectInfoEntry: The set of dialer configuration attributes for one port.
dialerDirectPortRef: The id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.
dialerDirectIfType: Interface type of the Dialer
dialerDirectMode: States whether the modem is connected to a Leased or Dial-Up phone line.
dialerDirectConnDelay: Max time for connection in seconds.
dialerDirectRtsDelay: Delay between arrival of DSR and activation of RTS circuit in msec.
dialerDirectState: State of the Direct dialer: closed(1) - Modem signals on a dial modem were lost. opening(2) - Link is being set up (modem dialing). asnwering(3) - Accepting call from remote. delaying(4) - Waiting for a timer to expire. opened(5) - Physical ...
dialerDirectRs232InfoTable: General Information Table for Direct dialer RS232.
dialerDirectRs232InfoEntry: The set of dialer configuration attributes for one port.
dialerDirectRs232PortRef: The id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.
dialerDirectRs232DbounceDelay: This applies to Leased line only. It is the amount of time, expressed in msecs, that DSR signal stays on.
dialerDirectRs232DtrSignal: The current status of the DTR signal.
dialerDirectRs232DsrSignal: The current status of the DSR signal.
dialerDirectRs232RiSignal: The current status of the RI signal. This is set to ON when there is an incoming call.
dialerDirectX21InfoTable: General Information Table for Direct dialer X21.
dialerDirectX21InfoEntry: The set of dialer configuration attributes for one port.
dialerDirectX21PortRef: The id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.
dialerDirectX21CtrlSignal: The control circuit status.
dialerDirectX21IndicSignal: The indication circuit status.
dialerV25bisInfoTable: General Information Table for V25Bis dialer.
dialerV25bisInfoEntry: The set of dialer configuration attributes for one port.
dialerV25bisPortRef: The Port Number.
dialerV25bisPrimaryNum: The main telephone number stored in the dialer.
dialerV25bisSecondaryNum: The alternate telephone number stored in the dialer. This number is dialed if the main number is busy of if there is no answer.
dialerV25bisAnsEnable: States whether or not the dialer answers incoming calls.
dialerV25bisRetryAllowed: Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
dialerV25bisMaxRetries: Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
dialerV25bisRetryDelay: The amount of time in msecs between redial attempts.
dialerV25bisConnDelay: Maximum delay for connection establishment (secs).
dialerV25bisOnOffDelay: The delay allowed in seconds for the DSR to go off before hangup.
dialerV25bisLossDelay: Amount of delay in msecs before DSR debouncing for OFF.
dialerV25bisMinDsrOnDelay: Amount of delay in msecs before DSR debouncing for ON.
dialerV25bisRiDtrDelay: Amount of delay in msec before raising DTR when RING occurs.
dialerV25bisHangupDelay: Amount of delay in secs before hangup, if DSR goes OFF in connected state.
dialerV25bisDeltaRiDelay: Delay in msecs before rings are no longer occur.
dialerV25bisCtsOnDelay: Maximum delay in msecs for sending a message to the modem.
dialerV25bisDtrSignal: DTR status.
dialerV25bisDsrSignal: DSR status.
dialerV25bisCtsSignal: CTS status.
dialerV25bisRiSignal: RI status.
dialerV25bisState: The status of the V.25bis modem: on-hook (1) - Modem not active ready (2) - Connection established dialing (3) - Dialing a number connect (4) - Successful dial attemp data-tran (5) - Data transfer state enabled retrying (6) - Awaiting call attempt ringin ...
dialerAtCmdInfoEntry: The set of dialer configuration attributes for one port.
dialerAtCmdPortRef: The Port Number.
dialerAtCmdPrimaryNum: The main telephone number stored in the dialer.
dialerAtCmdSecondaryNum: The alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.
dialerAtCmdAnsEnable: States whether or not the dialer answers incoming calls.
dialerAtCmdRetryAllowed: Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
dialerAtCmdMaxRetries: Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
dialerAtCmdRetryDelay: The amount of time in msecs between redial attempts.
dialerAtCmdConnDelay: Maximum delay for connection establishment (secs).
dialerAtCmdOnOffDelay: The delay allowed in seconds for the DSR signal to go off before hangup.
dialerAtCmdLossDelay: Number of msecs allowed before DSR debouncing for OFF.
dialerAtCmdMinDsrOnDelay: msecs DSR debouncing for ON before going OFF.
dialerAtCmdRiDtrDelay: Amount of delay in msec, before raising DTR when RING occurs.
dialerAtCmdHangupDelay: Amount of delay in secs before hangup, if DSR goes OFF in connected state.
dialerAtCmdDeltaRiDelay: delay in msecs before rings no longer occur.
dialerAtCmdParity: The parity.
dialerAtCmdBitsPerByte: The number of data bits per byte.
dialerAtCmdModemSpeed: Modem Speed.
dialerAtCmdDtrSignal: DTR status.
dialerAtCmdDsrSignal: DSR status.
dialerAtCmdRiSignal: RI status.
dialerAtCmdState: The status of the AT modem: on-hook (1) - modem not active dialing (2) - dialing a number answering (3) - accepting call from remote ringing (4) - incoming call present retrying (5) - awaiting new call attempt off-hook (6) - Modem active hanging-up (7) - ...
dialerV22BisDnaInfoEntry: The set of dialer configuration attributes for one port.
dialerV22BisDnaPortRef: The Port Number.
dialerV22BisDnaPrimaryNum: The main telephone number stored in the dialer.
dialerV22BisDnaSecondaryNum: The alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.
dialerV22BisDnaAnsEnable: States whether or not the dialer answers incoming calls.
dialerV22BisDnaRetryAllowed: Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
dialerV22BisDnaMaxRetries: Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
dialerV22BisDnaCallProgress: Call progress tone detection.
dialerV22BisDnaDecadic: Indicates whether Decadic dialing is active or not. Decadic dialing does the following: each digit you dial is subtracted from 10, and the result is the number actually dialed.
dialerV22BisDnaMakeBreakRatio: Ratio for PULSE and DIAL make and break time.
dialerV22BisDnaRetryDelay: The amount of time in msecs between redial attempts.
dialerV22BisDnaMinDialDelay: The length of delay (msec) associated with a comma placed in a dialing command.
dialerV22BisDnaWaitDialTone: The amount of time (msec) the modem waits when it encounters the wait for dial tone modifier in dial string.
dialerV22BisDnaWaitCarrier: The amount of time (msec) the modem waits for valid carrier after completing a dial.
dialerV22BisDnaHndshkAbortTimer: The amount of time (sec) allowed before the call is aborted if DSR does not go ON.
dialerV22BisDnaGuardTone: Indicates a guard tone frequency.
dialerV22BisDnaPulseDelay: The delay (msec) between digits dialed on a pulse line.
dialerV22BisDnaDTMFDuration: The tone duration (msec) used in DMTF dialing.
dialerV22BisDnaDTMFDelay: The delay (msec) between digits dialed when in tone dial mode.
dialerV22BisDnaDTMFLevel: The tone dialing level attenuation in dB.
dialerV22BisDnaTxLevel: The attenuation level (Db) on data transmission, once the handshake is completed with the remote modem.
dialerV22BisDnaRxLevel: Minimum acceptable receiver threshold value. This indicates whether a 3dB attenuation is used on the receive signal at line input.
dialerV22BisDnaRiNbr: The number of rings required before the modem answers, if it is set to auto-answer mode.
dialerV22BisDnaDeltaRiDelay: delay in msecs before rings no longer occur.
dialerV22BisDnaRiDtrDelay: Amount of delay in msec, before raising DTR when RING occurs.
dialerV22BisDnaDsrRtsDelay: Delay between arrival of DSR and activation of RTS circuit in msec.
dialerV22BisDnaModemSpeed: Modem Speed.
dialerV22BisDnaDtrSignal: DTR status.
dialerV22BisDnaDsrSignal: DSR status.
dialerV22BisDnaRiSignal: RI status.
dialerV22BisDnaCdSignal: Carrier detect status.
dialerV22BisDnaToneInd: Tone indication.
dialerV22BisDnaDloInd: Dial line occupied indication.
dialerV22BisDnaState: Status of the V22bis Dna modem: dialing-phone (1) - Dialing a number on the phone attached to the DNA phone plug. dialing-mdm (2) - Dialing a remote modem retrying (3) - Awaiting call attempt ringing (4) - Incoming call present line-busy (5) ...
dialerV22BisImcInfoEntry: The set of dialer configuration attributes for one port.
dialerV22BisImcPortRef: The Port Number.
dialerV22BisImcPrimaryNum: The main telephone number stored in the dialer.
dialerV22BisImcSecondaryNum: The alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.
dialerV22BisImcAnsEnable: States whether or not the dialer answers incoming calls.
dialerV22BisImcRetryAllowed: Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
dialerV22BisImcMaxRetries: Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
dialerV22BisImcCallProgress: Call progress tone detection.
dialerV22BisImcDecadic: Indicates whether Decadic dialing is active or not. Decadic dialing does the following: each digit you dial is subtracted from 10, and the result is the number actually dialed.
dialerV22BisImcMakeBreakRatio: Ratio of PULSE and DIAL make and break time.
dialerV22BisImcRetryDelay: The amount of time in msecs between redial attempts.
dialerV22BisImcMinDialDelay: The length of delay (msec) associated with a comma placed in a dialing command.
dialerV22BisImcWaitDialTone: The amount of time (msec) the modem waits when it encounters the wait for dial tone modifier in dial string.
dialerV22BisImcWaitCarrier: The amount of time (msec) the modem waits for valid carrier after completing a dial.
dialerV22BisImcHndshkAbortTimer: The amount of time (sec) allowed before the call is aborted if DSR does not go ON.
dialerV22BisImcGuardTone: Indicates a guard tone frequency.
dialerV22BisImcPulseDelay: The delay between (msec) digits dialed on a pulse line.
dialerV22BisImcDTMFDuration: The tone (msec) duration used in DMTF dialing.
dialerV22BisImcDTMFDelay: The delay (msec) between digits dialed when in tone dial mode.
dialerV22BisImcDTMFLevel: The tone dialing level attenuation in dB.
dialerV22BisImcTxLevel: The attenuation level (Db) on data transmission, once the handshake is completed with the remote modem.
dialerV22BisImcRxLevel: Minimum acceptable receiver threshold value. This indicates whether a 3dB attenuation is used on the receive signal at line input.
dialerV22BisImcRiNbr: The numbet of rings required before the modem answers, if it is set to auto-answer mode.
dialerV22BisImcDeltaRiDelay: delay in msecs before rings no longer occur.
dialerV22BisImcRiDtrDelay: Amount of delay in msec, before raising DTR when RING occurs.
dialerV22BisImcDsrRtsDelay: Delay between arrival of DSR and activation of RTS circuit in msec.
dialerV22BisImcModemSpeed: Modem Speed.
dialerV22BisImcDtrSignal: DTR status.
dialerV22BisImcDsrSignal: DSR status.
dialerV22BisImcRiSignal: RI status.
dialerV22BisImcCdSignal: Carrier Detect status.
dialerV22BisImcToneInd: Tone indication.
dialerV22BisImcDloInd: Dial line occupied indication.
dialerV22BisImcLineType: States whether the modem is connected to a Leased or Dial-Up phone line.
dialerV22BisImcLeasedOpertn: This applies to Leased line type only. This field states whether the dialer will go off-hook in Originate or Answer mode.
dialerV22BisImcSpeakerLevel: The volume level of the Eiconcard's speaker.
dialerV22BisImcState: Status of the V22bis Imc modem: dialing-phone (1) - Dialing a number on the phone attached to the DNA phone plug. dialing-mdm (2) - Dialing a remote modem retrying (3) - Awaiting call attempt ringing (4) - Incoming call present line-busy (5) ...
dialerV32BisInfoEntry: The set of dialer configuration attributes for one port.
dialerV32BisPortRef: The Port Number.
dialerV32BisPrimNum: The main telephone number stored in the dialer.
dialerV32BisSecNum: The alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.
dialerV32BisOverrNum: Override number.
dialerV32BisCurrNum: Current number.
dialerV32BisPrimBitRate: Default bit rate for primary number.
dialerV32BisSecBitRate: Default bit rate for secondary number.
dialerV32BisOverrBitRate: Default bit rate for override number.
dialerV32BisCurrBitRate: Default bit rate for current number.
dialerV32BisPrimConfig: Dial modem primary configuration
dialerV32BisSecConfig: Dial modem secondary configuration
dialerV32BisOverrConfig: Dial modem override configuration
dialerV32BisCurrConfig: Dial modem current configuration
dialerV32BisCurrRetry: Current number of retries.
dialerV32BisRingCount: Incoming ring counter.
dialerV32BisAnsEnable: States whether or not the dialer answers incoming calls.
dialerV32BisDialMethod: The method used for dialing.
dialerV32BisRetry: Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
dialerV32BisCallFailure: Reason for last call failure.
dialerV32BisCarrierDetect: Delay in msec to wait for verification of carrier detect.
dialerV32BisCarrierWait: Delay in msec to wait for carrier detect.
dialerV32BisHangupVerify: Delay in msec to wait to verify for hangup.
dialerV32BisHangupSignal: Hangup signal state.
dialerV32BisTxLevel: The attenuation level (Db) on data transmission, once the handshake is completed with the remote modem.
dialerV32BisRxLevel: Minimum acceptable receiver threshold value. This indicates whether a 3dB attenuation is used on the receive signal at line input.
dialerV32BisGuardTone: Indicates a guard tone frequency.
dialerV32BisLeasedLine: Dial or leased line.
dialerV32BisLeaseMode: This applies to Leased line type only. This field states whether the dialer will go off-hook in Originate or Answer mode.
dialerV32BisLLTxLevel: The attenuation level (Db) on data transmission once the handshake is completed with the remote modem (for leased line).
dialerV32BisLLConfig: Leased line configuration
dialerV32BisLLBitRate: Leased line bit rate.
dialerV32BisCallingTone: Calling tone state.
dialerV32BisAutoMode: Auto mode state (fallback/forward).
dialerV32BisRetryAllowed: Indicates whether or not the dialer will try to redial a number that is busy or does not answer.
dialerV32BisMaxRetry: Specifies how many times a number will be redialed if it is busy or otherwise unresponsive.
dialerV32BisDialTone: The dial tone state.
dialerV32BisDialToneWait: The amount of time (msec) the modem waits when it encounters the wait for dial tone modifier in dial string.
dialerV32BisRetryWait: Retry timer delay.
dialerV32BisHangupWait: Hangup timer delay.
dialerV32BisDialPauseWait: maximum delay before dial.
dialerV32BisDeltaRiWait: Maximum delay (msec) between 2 rings.
dialerV32BisDTMFDuration: The tone duration (msec) used in DMTF dialing.
dialerV32BisDTMFDelay: The delay (msec) between digits dialed when in tone dial mode.
dialerV32BisDTMFFreq1Level: DTMF high frequency power level.
dialerV32BisDTMFFreq2Level: DTMF low frequency power level.
dialerV32BisPulseMakeTime: Pulse make time (msec).
dialerV32BisPulseBreakTime: Pulse break time (msec).
dialerV32BisPulseDelay: Pulse interdigit delay (msec).
dialerV32BisSpeakerLevel: The volume level of the Eiconcard's speaker.
dialerV32BisRiToAnswer: Number of rings befor answering.
dialerV32BisAnswerBitRate: Answer bit rate.
dialerV32BisAnswerConfig: Answer configuration.
dialerV32BisRetrain: .
dialerV32BisEqmLevel: .
dialerV32BisRiOnOffDetect: Ring signal status.
dialerV32BisCdDetect: Carrier detect status.
dialerV32BisRingbackDetect: Ringback signal detect status.
dialerV32BisAnswerDetect: Answer tone detect status.
dialerV32BisBusyDetect: Busy tone detect status.
dialerV32BisDiscDetect: Disconnect detect status.
dialerV32BisCdSignal: CD signal status.
dialerV32BisDsrSignal: DSR signal status.
dialerV32BisState: State of the V32bis dialer: m-closed (1) - Dialer not active m-opened (2) - No connection establised m-local-test (3) - Local analog loopback m-ringing (4) - Incoming call present m-dialing (5) - Dialing a number m-answering (6) - Call answer in prog ...
dialerControlEntry: The set of attributes for one entry per port.
dialerCtrlPortRef: The Port number of the dialer.
dialerCtrlAction: The Action states. exec (1) - This action executes the script file which would be set in dialerCtrlScriptFile. dial (2) - This action dials the number stored in dialerCtrlMainNumber. if dialerCtrlMainNumber is not set then the dialerCtrlPrimary number is ...
dialerCtrlDirectDSROnOff: Defines the setting of the Data Rate Select signal. Setting this mib is valid only if the dialer type is Direct and the interface is RS-232.
dialerCtrlNumber: The primary Phone Number
dialerCtrlScriptFile: The Complete path where the Dialer Script file resides.
dialerCtrlActionState: The state of the action operation performed by the Agent as a result of setting the values to the dialerCtrlAction. The Management station will poll that variable after initiating an action. The value done(1) indicates that the action terminated success ...
dialerCtrlActionError: If the value is 0, this means no error. Otherwise, the value indicates the error code returned after the action operation.
dialerCtrlConfig: The config to which the V32 dialer will have to be set. This information is only used when using a V32 dialer.
dialerCtrlBitRate: The Bit Rate to which the V32 dialer will have to be set. This information is only used when using a V32 dialer.
dialerCtrlType: The remote directory number type. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
dialerCtrlPlan: The remote directory number plan. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
dialerCtrlSub: The remote subaddress. When in the connected state, the remote subaddress dialer is displayed. Otherwise, the stored subaddress is displayed. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
dialerCtrlSubType: The local subaddress type. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
dialerCtrlTns: The string identifying the selected long distance carrier. In ISDN terms, it is called the Transit Network Selection. This string is usually made of 3 digits and is assigned by Bellcore. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.
dialerCtrlNumberTemp: The temporary Phone Number. DEFINED ONLY FOR ISDN TESTS.
dialerCtrlDialMask: Read the mask state. DEFINED ONLY FOR TESTS.
dialerCtrlCallSpeed: Read the mask state. DEFINED ONLY FOR TESTS.
dialerIsdnStatusTable: The table for ISDN dialer Status.
dialerIsdnStatusEntry: The set of attributes for one port.
dialerIsdnStatusPortRef: The port number for which isdn status is displayed.
dialerIsdnStatusSwitchType: The current switch type in use for isdn.
dialerIsdnStatusChType: The isdn channel type, B channel or D channel.
dialerIsdnStatusL1State: The current state of layer 1 subsystem.
dialerIsdnStatusState: The current state of the ISDN dialer.
dialerIsdnNI1BChTable: The table for the ISDN NI1 BChannel dialer.
dialerIsdnNI1BChEntry: The set of attributes for one port.
dialerIsdnNI1BChPortRef: The port number which is configured for NI1_BChannel.
dialerIsdnNI1BChSpid: The Terminal's Service Profile IDentification.
dialerIsdnNI1BChSpidStatus: The current SPID status.
dialerIsdnNI1BChLocalDn: The local directory number type.
dialerIsdnNI1BChLocalSub: The local subaddress.
dialerIsdnNI1BChTnsDigs: The string identifying the selected long distance carrier. In ISDN terms, it is called the Transit Network Selection. This string is usually made of 3 digits and is assigned by Bellcore.
dialerIsdnNI1BChRemoteDn: When in the connected state, the number dialed is displayed. Otherwise, the stored number is displayed.
dialerIsdnNI1BChRemoteSub: When in the connected state, the remote subaddress dialer is displayed. Otherwise, the stored subaddress is displayed.
dialerIsdnNI1BChCallType: The current call type.
dialerIsdnNI1BChCallSpeed: The current call speed.
dialerIsdnNI1BChBChannel: The current B channel connected to.
dialerIsdnNI1BChAnsEnable: Answer Enable Status.
dialerIsdnNI1BChCcState: The state of call control subsystem.
dialerIsdnNI1BChCcNbCause: The number of causes saved.
dialerIsdnNI1BChCcCause: Last causes saved.
dialerIsdnNI1BChL3State: The state of layer 3 subsystem.
dialerIsdnNI1BChL2State: The state of layer 2 subsystem.
dialerIsdnNI1BChTeiValue: The value of the terminal is dynamic TEI.
dialerIsdnNI1BChTeiStatus: The status of the terminal's dynamic TEI.
dialerIsdnNI1BChLocalDnType: The local directory number type.
dialerIsdnNI1BChLocalDnPlan: The local directory number plan.
dialerIsdnNI1BChLocalSubType: The local subaddress type.
dialerIsdnNI1BChTnsNetId: The transit network id.
dialerIsdnNI1BChTnsIdPlan: The transit network plan.
dialerIsdnNI1BChRemoteDnType: The remote directory number type.
dialerIsdnNI1BChRemoteDnPlan: The remote directory number plan.
dialerIsdnNI1BChRemoteSubType: The local subaddress type.
dialerIsdnNI1BChScrStatus: The status of call screening.
dialerIsdnNI1BChCallOpt: The current call option.
dialerIsdnNI1BChStoDefined: The validity of sto_ elements.
dialerIsdnNI1BChStoDnType: The stored directory number type.
dialerIsdnNI1BChStoDnPlan: The stored directory number plan.
dialerIsdnNI1BChStoDn: The stored directory number.
dialerIsdnNI1BChStoSubType: The stored subaddress type.
dialerIsdnNI1BChStoSub: The stored subaddress.
dialerIsdnNI1BChStoTnsNetId: The stored transit network id.
dialerIsdnNI1BChStoTnsPlan: The stored transit network plan.
dialerIsdnNI1BChStoDigs: The stored transit network address.
dialerIsdnNI1BChStoBcType: The stored bearer cap. type.
dialerIsdnNI1BChStoBcOpt: The stored bearer cap. option.
dialerIsdnNI1DChTable: The table for the ISDN NI1 DChannel dialer.
dialerIsdnNI1DChEntry: The set of attributes for one port.
dialerIsdnNI1DChPortRef: The port number configured for the NI1 DChannel.
dialerIsdnNI1DChTeiValue: The static TEI value on the D Channel for data communications.
dialerIsdnNI1DChTeiStatus: The status of TEI - always ASSIGNED.
dialerIsdnNI1DChL2State: The current layer 2 state.
dialerIsdnNI1DChP3State: The current Packet layer state.
dialerIsdnNI1DChActState: The current activation FSM state.
dialerIsdnTR6BChTable: The table for the ISDN TR6 BChannel dialer.
dialerIsdnTR6BChEntry: The set of attributes for one port.
dialerIsdnTR6BChPortRef: The port number for which the 1TR6 BChannel info is displayed.
dialerIsdnTR6BChLocalDn: The local directory number type.
dialerIsdnTR6BChRemoteDn: When in the connected state, the number dialed is displayed. Otherwise, the stored number is displayed.
dialerIsdnTR6BChCallType: The current call type.
dialerIsdnTR6BChCallSpeed: The current call speed.
dialerIsdnTR6BChBChannel: The current B Channel connected to.
dialerIsdnTR6BChAnsEnable: Answer enable status.
dialerIsdnTR6BChCcState: The state of call control subsystem.
dialerIsdnTR6BChCcNbCause: The number of causes saved.
dialerIsdnTR6BChCcCause: Last causes saved.
dialerIsdnTR6BChL3State: The state of layer 3 subsystem.
dialerIsdnTR6BChL2State: The state of layer 2 subsystem.
dialerIsdnTR6BChLocalDnType: The local directory number type.
dialerIsdnTR6BChLocalDnPlan: The local directory number plan.
dialerIsdnTR6BChRemoteDnType: The remote directory number type.
dialerIsdnTR6BChRemoteDnPlan: The remote directory number plan.
dialerIsdnTR6BChScrStatus: The status of call screening.
dialerIsdnTR6BChCallOpt: The current call option.
dialerIsdnTR6BChTeiValue: The static TEI value on the D Channel for data communications.
dialerIsdnTR6BChTeiStatus: The status of TEI - always ASSIGNED.
dialerIsdnTR6BChStoDefined: The validity of sto_ elements.
dialerIsdnTR6BChStoDnType: The stored directory number type.
dialerIsdnTR6BChStoDnPlan: The stored directory number plan.
dialerIsdnTR6BChStoDn: The stored directory number.
dialerIsdnTR6BChStoBcType: The stored bearer cap. type.
dialerIsdnTR6BChStoBcOpt: The stored bearer cap. option.
dialerIsdnVN3BChTable: The table for the ISDN VN3 BChannel dialer.
dialerIsdnVN3BChEntry: The set of attributes for one port.
dialerIsdnVN3BChPortRef: The port number for which the VN3 BChannel info is displayed.
dialerIsdnVN3BChLocalDnType: The local directory number type.
dialerIsdnVN3BChLocalDnPlan: The local directory number plan.
dialerIsdnVN3BChLocalDn: The local directory number type.
dialerIsdnVN3BChLocalSubType: The local subaddress type.
dialerIsdnVN3BChLocalSub: The local directory number type.
dialerIsdnVN3BChRemoteDnType: The local directory number type.
dialerIsdnVN3BChRemoteDnPlan: The local directory number plan.
dialerIsdnVN3BChRemoteDn: The local directory number type.
dialerIsdnVN3BChRemoteSubType: The local subaddress type.
dialerIsdnVN3BChRemoteSub: The local directory number type.
dialerIsdnVN3BChCallType: The current call type.
dialerIsdnVN3BChCallSpeed: The current call speed.
dialerIsdnVN3BChBChannel: The current B Channel connected to.
dialerIsdnVN3BChAnsEnable: Answer enable status.
dialerIsdnVN3BChScrStatus: The status of call screening.
dialerIsdnVN3BChCallOpt: The current call option.
dialerIsdnVN3BChCcState: The state of call control subsystem.
dialerIsdnVN3BChCcNbCause: The number of causes saved.
dialerIsdnVN3BChCcCause: Last causes saved.
dialerIsdnVN3BChL3State: The state of layer 3 subsystem.
dialerIsdnVN3BChL2State: The state of layer 2 subsystem.
dialerIsdnVN3BChTeiValue: The static TEI value on the D Channel for data communications.
dialerIsdnVN3BChTeiStatus: The status of TEI - always ASSIGNED.
dialerIsdnVN3BChStoDefined: The validity of sto_ elements.
dialerIsdnVN3BChStoDnType: The stored directory number type.
dialerIsdnVN3BChStoDnPlan: The stored directory number plan.
dialerIsdnVN3BChStoDn: The stored directory number.
dialerIsdnVN3BChStoSubType: The stored subaddress type.
dialerIsdnVN3BChStoSub: The stored subaddress.
dialerIsdnVN3BChStoBcType: The stored bearer cap type.
dialerIsdnVN3BChStoBcOpt: The stored bearer cap option.
dialerIsdnVN3DChTable: The table for the ISDN VN3 DChannel dialer.
dialerIsdnVN3DChEntry: The set of attributes for one port.
dialerIsdnVN3DChPortRef: The port number for which the VN3 DChannel info is displayed.
dialerIsdnVN3DChTeiValue: The static TEI value on the D Channel for data communications.
dialerIsdnVN3DChTeiStatus: The status of TEI - always ASSIGNED.
dialerIsdnVN3DChL2State: The state of layer 2 subsystem.
dialerIsdnVN3DChP3State: The current Packet layer state.
dialerIsdnNET3BChTable: The table for the ISDN NET3 BChannel dialer.
dialerIsdnNET3BChEntry: The set of attributes for one port.
dialerIsdnNET3BChPortRef: The port number for which the NET3 BChannel info is displayed.
dialerIsdnNET3BChLocalDnType: The local directory number type.
dialerIsdnNET3BChLocalDnPlan: The local directory number plan.
dialerIsdnNET3BChLocalDn: The local directory number type.
dialerIsdnNET3BChLocalSubType: The local subaddress type.
dialerIsdnNET3BChLocalSub: The local directory number type.
dialerIsdnNET3BChRemoteDnType: The local directory number type.
dialerIsdnNET3BChRemoteDnPlan: The local directory number plan.
dialerIsdnNET3BChRemoteDn: The local directory number type.
dialerIsdnNET3BChRemoteSubType: The local subaddress type.
dialerIsdnNET3BChRemoteSub: The local directory number type.
dialerIsdnNET3BChCallType: The current call type.
dialerIsdnNET3BChCallSpeed: The current call speed.
dialerIsdnNET3BChBChannel: The current B Channel connected to.
dialerIsdnNET3BChAnsEnable: Answer enable status.
dialerIsdnNET3BChTnsNetId: The transit network id.
dialerIsdnNET3BChTnsIdPlan: The transit network plan.
dialerIsdnNET3BChTnsDigs: The string identifying the selected long distance carrier. In ISDN terms, it is called the Transit Network Selection. This string is usually made of 3 digits and is assigned by Bellcore.
dialerIsdnNET3BChScrStatus: The status of call screening.
dialerIsdnNET3BChCallOpt: The current call option.
dialerIsdnNET3BChCcState: The state of call control subsystem.
dialerIsdnNET3BChCcNbCause: The number of causes saved.
dialerIsdnNET3BChCcCause: Last causes saved.
dialerIsdnNET3BChL3State: The state of layer 3 subsystem.
dialerIsdnNET3BChL2State: The state of layer 2 subsystem.
dialerIsdnNET3BChTeiValue: The static TEI value on the D Channel for data communications.
dialerIsdnNET3BChTeiStatus: The status of TEI - always ASSIGNED.
dialerIsdnNET3BChStoDefined: The validity of sto_ elements.
dialerIsdnNET3BChStoDnType: The stored directory number type.
dialerIsdnNET3BChStoDnPlan: The stored directory number plan.
dialerIsdnNET3BChStoDn: The stored directory number.
dialerIsdnNET3BChStoSubType: The stored subaddress type.
dialerIsdnNET3BChStoSub: The stored subaddress.
dialerIsdnNET3BChStoTnsNetId: The stored transit network id.
dialerIsdnNET3BChStoTnsPlan: The stored transit network plan.
dialerIsdnNET3BChStoDigs: The stored transit network address.
dialerIsdnNET3BChStoBcType: The stored bearer cap. type.
dialerIsdnNET3BChStoBcOpt: The stored bearer cap. option.
dialerIsdnTPHBChTable: The table for the ISDN TPH BChannel dialer.
dialerIsdnTPHBChEntry: The set of attributes for one port.
dialerIsdnTPHBChPortRef: The port number for which the TPH BChannel info is displayed.
dialerIsdnTPHBChLocalDnType: The local directory number type.
dialerIsdnTPHBChLocalDnPlan: The local directory number plan.
dialerIsdnTPHBChLocalDn: The local directory number type.
dialerIsdnTPHBChLocalSubType: The local subaddress type.
dialerIsdnTPHBChLocalSub: The local directory number type.
dialerIsdnTPHBChRemoteDnType: The local directory number type.
dialerIsdnTPHBChRemoteDnPlan: The local directory number plan.
dialerIsdnTPHBChRemoteDn: The local directory number type.
dialerIsdnTPHBChRemoteSubType: The local subaddress type.
dialerIsdnTPHBChRemoteSub: The local directory number type.
dialerIsdnTPHBChCallType: The current call type.
dialerIsdnTPHBChCallSpeed: The current call speed.
dialerIsdnTPHBChBChannel: The current B Channel connected to.
dialerIsdnTPHBChAnsEnable: Answer enable status.
dialerIsdnTPHBChScrStatus: The status of call screening.
dialerIsdnTPHBChCallOpt: The current call option.
dialerIsdnTPHBChCcState: The state of call control subsystem.
dialerIsdnTPHBChCcNbCause: The number of causes saved.
dialerIsdnTPHBChCcCause: Last causes saved.
dialerIsdnTPHBChL3State: The state of layer 3 subsystem.
dialerIsdnTPHBChL2State: The state of layer 2 subsystem.
dialerIsdnTPHBChTeiValue: The static TEI value on the D Channel for data communications.
dialerIsdnTPHBChTeiStatus: The status of TEI - always ASSIGNED.
dialerIsdnTPHBChStoDefined: The validity of sto_ elements.
dialerIsdnTPHBChStoDnType: The stored directory number type.
dialerIsdnTPHBChStoDnPlan: The stored directory number plan.
dialerIsdnTPHBChStoDn: The stored directory number.
dialerIsdnTPHBChStoSubType: The stored subaddress type.
dialerIsdnTPHBChStoSub: The stored subaddress.
dialerIsdnTPHBChStoBcType: The stored bearer cap. type.
dialerIsdnTPHBChStoBcOpt: The stored bearer cap. option.
dialerIsdnTPHDChTable: The table for the ISDN TPH DChannel dialer.
dialerIsdnTPHDChEntry: The set of attributes for one port.
dialerIsdnTPHDChPortRef: The port number for which the TPH DChannel info is displayed.
dialerIsdnTPHDChTeiValue: The static TEI value on the D Channel for data communications.
dialerIsdnTPHDChTeiStatus: The status of TEI - always ASSIGNED.
dialerIsdnTPHDChL2State: The state of layer 2 subsystem.
dialerIsdnTPHDChP3State: The current Packet layer state.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list