HDSL2-SHDSL-LINE-MIB Download

MIBs list

This MIB module defines a collection of objects for managing HDSL2/SHDSL lines. An agent may reside at either end of the line; however, the MIB module is designed to require no management communication between the modems beyond that inherent in the low-level EOC line protocol as defined in ANSI T1E1.4/2000-006 (for HDSL2 lines) or in ITU G.991.2 (for SHDSL lines).

IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for HDSL2-SHDSL-LINE-MIB

hdsl2ShdslSpanConfTable: This table supports overall configuration of HDSL2/SHDSL spans. Entries in this table MUST be maintained in a persistent manner.
hdsl2ShdslSpanConfEntry: An entry in the hdsl2ShdslSpanConfTable. Each entry represents the complete span in a single HDSL2/SHDSL line. It is indexed by the ifIndex of the associated HDSL2/SHDSL line.
hdsl2ShdslSpanConfNumRepeaters: This object provisions the number of repeaters/regenerators in this HDSL2/SHDSL span.
hdsl2ShdslSpanConfProfile: This object is a pointer to a span configuration profile in the hdsl2ShdslSpanConfProfileTable, which applies to this span. The value of this object is the index of the referenced profile in the hdsl2ShdslSpanConfProfileTable. Note that span configurati ...
hdsl2ShdslSpanConfAlarmProfile: This object is a pointer to an alarm configuration profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold configuration ...
hdsl2ShdslSpanStatusTable: This table provides overall status information of HDSL2/SHDSL spans. This table contains live data from equipment. As such, it is NOT persistent.
hdsl2ShdslSpanStatusEntry: An entry in the hdsl2ShdslSpanStatusTable. Each entry represents the complete span in a single HDSL2/SHDSL line. It is indexed by the ifIndex of the associated HDSL2/SHDSL line.
hdsl2ShdslStatusNumAvailRepeaters: Contains the actual number of repeaters/regenerators discovered in this HDSL2/SHDSL span.
hdsl2ShdslStatusMaxAttainableLineRate: Contains the maximum attainable line rate in this HDSL2/SHDSL span. This object provides the maximum rate the line is capable of achieving. This is based upon measurements made during line probing. This rate includes payload (user data) and any applica ...
hdsl2ShdslStatusActualLineRate: Contains the actual line rate in this HDSL2/SHDSL span. This SHOULD equal ifSpeed. This rate includes payload (user data) and any applicable framing overhead
hdsl2ShdslStatusTransmissionModeCurrent: Contains the current Power Spectral Density (PSD) regional setting of the HDSL2/SHDSL span.
hdsl2ShdslStatusMaxAttainablePayloadRate: Contains the maximum attainable payload (user data) line rate in this HDSL2/SHDSL span. This object provides the maximum rate the line is capable of achieving. This is based upon measurements made during line probing. Any framing overhead is not includ ...
hdsl2ShdslStatusActualPayloadRate: Contains the actual line rate in this HDSL2/SHDSL span. Any framing overhead is not included.
hdsl2ShdslInventoryTable: This table supports retrieval of unit inventory information available via the EOC from units in an HDSL2/SHDSL line. Entries in this table are dynamically created during the line discovery process. The life cycle for these entries is as follows: - xtu di ...
hdsl2ShdslInventoryEntry: An entry in the hdsl2ShdslInventoryTable. Each entry represents inventory information for a single unit in an HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the associated unit.
hdsl2ShdslInvIndex: Each entry in this table corresponds to a physical element in an HDSL2/SHDSL span. It is based on the EOC unit addressing scheme with reference to the xtuC.
hdsl2ShdslInvVendorID: Vendor ID as reported in an Inventory Response message.
hdsl2ShdslInvVendorModelNumber: Vendor model number as reported in an Inventory Response message.
hdsl2ShdslInvVendorSerialNumber: Vendor serial number as reported in an Inventory Response message.
hdsl2ShdslInvVendorEOCSoftwareVersion: Vendor EOC version as reported in a Discovery Response message.
hdsl2ShdslInvStandardVersion: Version of the HDSL2/SHDSL standard implemented, as reported in an Inventory Response message.
hdsl2ShdslInvVendorListNumber: Vendor list number as reported in an Inventory Response message.
hdsl2ShdslInvVendorIssueNumber: Vendor issue number as reported in an Inventory Response message.
hdsl2ShdslInvVendorSoftwareVersion: Vendor software version as reported in an Inventory Response message.
hdsl2ShdslInvEquipmentCode: Equipment code conforming to ANSI T1.213, Coded Identification of Equipment Entities.
hdsl2ShdslInvVendorOther: Other vendor information as reported in an Inventory Response message.
hdsl2ShdslInvTransmissionModeCapability: Contains the transmission mode capability of the SHDSL unit.
hdsl2ShdslEndpointConfTable: This table supports configuration parameters for segment endpoints in an HDSL2/SHDSL line. As this table is indexed by ifIndex, it MUST be maintained in a persistent manner.
hdsl2ShdslEndpointConfEntry: An entry in the hdsl2ShdslEndpointConfTable. Each entry represents a single segment endpoint in an HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit, the side of the unit, and the wire pair of the a ...
hdsl2ShdslEndpointSide: The side of the unit associated with this segment endpoint -- Network/Customer side -- as per the Hdsl2ShdslUnitSide textual convention.
hdsl2ShdslEndpointWirePair: The wire pair of the modem associated with this segment endpoint as per the Hdsl2ShdslWirePair textual convention.
hdsl2ShdslEndpointAlarmConfProfile: This object configures the alarm threshold values to be used for this segment endpoint. The values are obtained from the alarm configuration profile referenced by this object. The value of this object is the index of the referenced profile in the hdsl2S ...
hdsl2ShdslEndpointCurrTable: This table contains current status and performance information for segment endpoints in HDSL2/SHDSL lines. As with other tables in this MIB module indexed by ifIndex, entries in this table MUST be maintained in a persistent manner.
hdsl2ShdslEndpointCurrEntry: An entry in the hdsl2ShdslEndpointCurrTable. Each entry contains status and performance information relating to a single segment endpoint. It is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit, the side of the unit, and ...
hdsl2ShdslEndpointCurrAtn: The current loop attenuation for this endpoint as reported in a Network or Customer Side Performance Status message.
hdsl2ShdslEndpointCurrSnrMgn: The current SNR margin for this endpoint as reported in a Status Response/SNR message.
hdsl2ShdslEndpointCurrStatus: Contains the current state of the endpoint. This is a bit-map of possible conditions. The various bit positions are as follows: noDefect There are no defects on the line. powerBackoff Indicates enhanced Power Backoff. deviceFault ...
hdsl2ShdslEndpointES: Count of Errored Seconds (ES) on this endpoint since the xU was last restarted.
hdsl2ShdslEndpointSES: Count of Severely Errored Seconds (SES) on this endpoint since the xU was last restarted.
hdsl2ShdslEndpointCRCanomalies: Count of CRC anomalies on this endpoint since the xU was last restarted.
hdsl2ShdslEndpointLOSWS: Count of Loss of Sync Word (LOSW) Seconds on this endpoint since the xU was last restarted.
hdsl2ShdslEndpointUAS: Count of Unavailable Seconds (UAS) on this endpoint since the xU was last restarted.
hdsl2ShdslEndpointCurr15MinTimeElapsed: Total elapsed seconds in the current 15-minute interval.
hdsl2ShdslEndpointCurr15MinES: Count of Errored Seconds (ES) in the current 15-minute interval.
hdsl2ShdslEndpointCurr15MinSES: Count of Severely Errored Seconds (SES) in the current 15-minute interval.
hdsl2ShdslEndpointCurr15MinCRCanomalies: Count of CRC anomalies in the current 15-minute interval.
hdsl2ShdslEndpointCurr15MinLOSWS: Count of Loss of Sync Word (LOSW) Seconds in the current 15-minute interval.
hdsl2ShdslEndpointCurr15MinUAS: Count of Unavailable Seconds (UAS) in the current 15-minute interval.
hdsl2ShdslEndpointCurr1DayTimeElapsed: Number of seconds that have elapsed since the beginning of the current 1-day interval.
hdsl2ShdslEndpointCurr1DayES: Count of Errored Seconds (ES) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.
hdsl2ShdslEndpointCurr1DaySES: Count of Severely Errored Seconds (SES) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.
hdsl2ShdslEndpointCurr1DayCRCanomalies: Count of CRC anomalies during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.
hdsl2ShdslEndpointCurr1DayLOSWS: Count of Loss of Sync Word (LOSW) Seconds during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.
hdsl2ShdslEndpointCurr1DayUAS: Count of Unavailable Seconds (UAS) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.
hdsl2ShdslEndpointCurrTipRingReversal: This object indicates the state of the tip/ring for the wire pair.
hdsl2ShdslEndpointCurrActivationState: This object indicates the activation or training state of the wire pair.
hdsl2Shdsl15MinIntervalTable: This table provides one row for each HDSL2/SHDSL endpoint performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
hdsl2Shdsl15MinIntervalEntry: An entry in the hdsl2Shdsl15MinIntervalTable.
hdsl2Shdsl15MinIntervalNumber: Performance Data Interval number. Interval 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
hdsl2Shdsl15MinIntervalES: Count of Errored Seconds (ES) during the interval.
hdsl2Shdsl15MinIntervalSES: Count of Severely Errored Seconds (SES) during the interval.
hdsl2Shdsl15MinIntervalCRCanomalies: Count of CRC anomalies during the interval.
hdsl2Shdsl15MinIntervalLOSWS: Count of Loss of Sync Word (LOSW) Seconds during the interval.
hdsl2Shdsl15MinIntervalUAS: Count of Unavailable Seconds (UAS) during the interval.
hdsl2Shdsl1DayIntervalTable: This table provides one row for each HDSL2/SHDSL endpoint performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
hdsl2Shdsl1DayIntervalEntry: An entry in the hdsl2Shdsl1DayIntervalTable.
hdsl2Shdsl1DayIntervalNumber: History Data Interval number. Interval 1 is the most recent previous day; interval 30 is 30 days ago. Intervals 2..30 are optional.
hdsl2Shdsl1DayIntervalMoniSecs: The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any rea ...
hdsl2Shdsl1DayIntervalES: Count of Errored Seconds (ES) during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.
hdsl2Shdsl1DayIntervalSES: Count of Severely Errored Seconds (SES) during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.
hdsl2Shdsl1DayIntervalCRCanomalies: Count of CRC anomalies during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.
hdsl2Shdsl1DayIntervalLOSWS: Count of Loss of Sync Word (LOSW) Seconds during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.
hdsl2Shdsl1DayIntervalUAS: Count of Unavailable Seconds (UAS) during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.
hdsl2ShdslEndpointMaintTable: This table supports maintenance operations (e.g., loopbacks) to be performed on HDSL2/SHDSL segment endpoints. This table contains live data from equipment. As such, it is NOT persistent.
hdsl2ShdslEndpointMaintEntry: An entry in the hdsl2ShdslEndpointMaintTable. Each entry corresponds to a single segment endpoint and is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit, and the side of the unit.
hdsl2ShdslMaintLoopbackConfig: This object controls configuration of loopbacks for the associated segment endpoint. The status of the loopback is obtained via the hdsl2ShdslEndpointCurrStatus object.
hdsl2ShdslMaintTipRingReversal: This object indicates the state of the tip/ring pair at the associated segment endpoint.
hdsl2ShdslMaintPowerBackOff: This object configures the receiver at the associated segment endpoint to operate in default or enhanced power backoff mode.
hdsl2ShdslMaintSoftRestart: This object enables the manager to trigger a soft restart of the modem at the associated segment endpoint. The manager may only set this object to the 'restart(2)' value, which initiates a restart. The agent will perform a restart after approximately 5 ...
hdsl2ShdslUnitMaintTable: This table supports maintenance operations for units in a HDSL2/SHDSL line. Entries in this table MUST be maintained in a persistent manner.
hdsl2ShdslUnitMaintEntry: An entry in the hdsl2ShdslUnitMaintTable. Each entry corresponds to a single unit and is indexed by the ifIndex of the HDSL2/SHDSL line and the UnitId of the associated unit.
hdsl2ShdslMaintLoopbackTimeout: This object configures the timeout value for loopbacks initiated at segments endpoints contained in the associated unit. A value of 0 disables the timeout.
hdsl2ShdslMaintUnitPowerSource: This object indicates the DC power source being used by the associated unit.
hdsl2ShdslSpanConfProfileTable: This table supports definitions of span configuration profiles for SHDSL lines. HDSL2 does not support these configuration options. This table MUST be maintained in a persistent manner.
hdsl2ShdslSpanConfProfileEntry: Each entry corresponds to a single span configuration profile. Each profile contains a set of span configuration parameters. The configuration parameters in a profile are applied to those lines referencing that profile (see the hdsl2ShdslSpanConfProfile ...
hdsl2ShdslSpanConfProfileName: This object is the unique index associated with this profile. Entries in this table are referenced via the object hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry.
hdsl2ShdslSpanConfWireInterface: This object configures the two-wire or optional four-wire, six-wire, or eight-wire operation for SHDSL lines.
hdsl2ShdslSpanConfMinLineRate: This object configures the minimum transmission rate for the associated SHDSL Line in bits-per-second (bps) and includes both payload (user data) and any applicable framing overhead. If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMax ...
hdsl2ShdslSpanConfMaxLineRate: This object configures the maximum transmission rate for the associated SHDSL Line in bits-per-second (bps) and includes both payload (user data) and any applicable framing overhead. If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMax ...
hdsl2ShdslSpanConfPSD: This object configures use of symmetric/asymmetric PSD (Power Spectral Density) Mask for the associated SHDSL Line. Support for symmetric PSD is mandatory for all supported data rates. Support for asymmetric PSD is optional.
hdsl2ShdslSpanConfTransmissionMode: This object specifies the regional setting for the SHDSL line.
hdsl2ShdslSpanConfRemoteEnabled: This object enables/disables support for remote management of the units in an SHDSL line from the STU-R via the EOC.
hdsl2ShdslSpanConfPowerFeeding: This object enables/disables support for optional power feeding in an SHDSL line.
hdsl2ShdslSpanConfCurrCondTargetMarginDown: This object specifies the downstream current condition target SNR margin for an SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.
hdsl2ShdslSpanConfWorstCaseTargetMarginDown: This object specifies the downstream worst-case target SNR margin for an SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.
hdsl2ShdslSpanConfCurrCondTargetMarginUp: This object specifies the upstream current-condition target SNR margin for an SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.
hdsl2ShdslSpanConfWorstCaseTargetMarginUp: This object specifies the upstream worst-case target SNR margin for an SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.
hdsl2ShdslSpanConfUsedTargetMargins: Indicates whether a target SNR margin is enabled or disabled. This is a bit-map of possible settings. The various bit positions are as follows: currCondDown - current-condition downstream target SNR margin enabled worstCaseDown - worst-case downstrea ...
hdsl2ShdslSpanConfReferenceClock: This object configures the clock reference for the STU-C in an SHDSL Line.
hdsl2ShdslSpanConfLineProbeEnable: This object enables/disables support for Line Probe of the units in an SHDSL line. When Line Probe is enabled, the system performs Line Probing to find the best possible rate. If Line Probe is disabled, the rate adaptation phase is skipped to shorten se ...
hdsl2ShdslSpanConfProfileRowStatus: This object controls creation/deletion of the associated entry in this table per the semantics of RowStatus. If an active entry is referenced in hdsl2ShdslSpanConfProfile, the entry MUST remain active until all references are removed.
hdsl2ShdslEndpointAlarmConfProfileTable: This table supports definitions of alarm configuration profiles for HDSL2/SHDSL segment endpoints. This table MUST be maintained in a persistent manner.
hdsl2ShdslEndpointAlarmConfProfileEntry: Each entry corresponds to a single alarm configuration profile. Each profile contains a set of parameters for setting alarm thresholds for various performance attributes monitored at HDSL2/SHDSL segment endpoints. Profiles may be created/deleted using th ...
hdsl2ShdslEndpointAlarmConfProfileName: This object is the unique index associated with this profile.
hdsl2ShdslEndpointThreshLoopAttenuation: This object configures the loop attenuation alarm threshold. When the current value of hdsl2ShdslEndpointCurrAtn reaches or exceeds this threshold, an hdsl2ShdslLoopAttenCrossing MAY be generated.
hdsl2ShdslEndpointThreshSNRMargin: This object configures the SNR margin alarm threshold. When the current value of hdsl2ShdslEndpointCurrSnrMgn reaches or drops below this threshold, a hdsl2ShdslSNRMarginCrossing MAY be generated.
hdsl2ShdslEndpointThreshES: This object configures the threshold for the number of Errored Seconds (ES) within any given 15-minute performance data collection interval. If the value of Errored Seconds in a particular 15-minute collection interval reaches/ exceeds this value, an hds ...
hdsl2ShdslEndpointThreshSES: This object configures the threshold for the number of Severely Errored Seconds (SES) within any given 15-minute performance data collection interval. If the value of Severely Errored Seconds in a particular 15-minute collection interval reaches/exceeds ...
hdsl2ShdslEndpointThreshCRCanomalies: This object configures the threshold for the number of CRC anomalies within any given 15-minute performance data collection interval. If the value of CRC anomalies in a particular 15-minute collection interval reaches/exceeds this value, an hdsl2ShdslPer ...
hdsl2ShdslEndpointThreshLOSWS: This object configures the threshold for the number of Loss of Sync Word (LOSW) Seconds within any given 15-minute performance data collection interval. If the value of LOSW in a particular 15-minute collection interval reaches/exceeds this value, an hds ...
hdsl2ShdslEndpointThreshUAS: This object configures the threshold for the number of Unavailable Seconds (UAS) within any given 15-minute performance data collection interval. If the value of UAS in a particular 15-minute collection interval reaches/exceeds this value, an hdsl2ShdslP ...
hdsl2ShdslEndpointAlarmConfProfileRowStatus: This object controls creation/deletion of the associated entry in this table as per the semantics of RowStatus. If an active entry is referenced in either hdsl2ShdslSpanConfAlarmProfile or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain active u ...
hdsl2ShdslSpanConfGroup: This group supports objects for configuring span-related parameters for HDSL2/SHDSL lines.
hdsl2ShdslSpanStatusGroup: This group supports objects for retrieving span-related status for HDSL2/SHDSL lines.
hdsl2ShdslInventoryShdslGroup: This group supports objects for retrieving SHDSL-specific inventory information.
hdsl2ShdslSpanShdslStatusGroup: This group supports objects for retrieving SHDSL-specific span-related status.
hdsl2ShdslInventoryGroup: This group supports objects that provide unit inventory information about the units in HDSL2/SHDSL lines.
hdsl2ShdslEndpointConfGroup: This group supports objects for configuring parameters for segment endpoints in HDSL2/SHDSL lines.
hdsl2ShdslEndpointCurrGroup: This group supports objects that provide current status and performance measurements relating to segment endpoints in HDSL2/SHDSL lines.
hdsl2Shdsl15MinIntervalGroup: This group supports objects that maintain historic performance measurements relating to segment endpoints in HDSL2/SHDSL lines in 15-minute intervals.
hdsl2Shdsl1DayIntervalGroup: This group supports objects that maintain historic performance measurements relating to segment endpoints in HDSL2/SHDSL lines in 1-day intervals.
hdsl2ShdslMaintenanceGroup: This group supports objects that provide support for maintenance actions for HDSL2/SHDSL lines.
hdsl2ShdslEndpointAlarmConfGroup: This group supports objects that allow configuration of alarm thresholds for various performance parameters for HDSL2/SHDSL lines.
hdsl2ShdslSpanConfProfileGroup: This group supports objects that constitute configuration profiles for configuring span-related parameters in SHDSL lines.
hdsl2ShdslWirePairGroup: This group supports objects that provide the status of SHDSL-specific wire pairs.
hdsl2ShdslPayloadRateGroup: This group supports objects for retrieving payload rates that exclude any framing overhead.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list