LIEBERT-POWERSURE-INTERACTIVE-UPS-MIB Download

lcUpsIdentManufacturer

The UPS manufacturer.

lcUpsIdentModel

The UPS Model designation.

lcUpsIdentSoftwareVersion

The UPS SNMP Agent software version.

lcUpsIdentSpecific

A reference to MIB definitions specific to the particular UPS being managed. This object is used to locate the product-specific MIB for this device. If this information is not present, its value should be the OBJECT IDENTIFIER { 0 0 }, which is a syntacti ...

lcUpsIdentFirmwareVersion

The firmware revision level of the UPS.

lcUpsIdentSerialNumber

The serial number of the UPS.

lcUpsIdentManufactureDate

The date of manufacture of the UPS.

lcUpsBatTimeRemaining

The estimated time to depletion of battery charge. (Unit of measure: Minute)

lcUpsBatVoltage

The current battery voltage. (Unit of measure: volt)

lcUpsBatCapacity

The current battery capacity in percentage of total available.

lcUpsInputFrequency

The current input frequency. (Unit of measure: Hertz)

lcUpsInputNumLines

The number of input lines utilized in this device. This entry indicates the number of rows in the input table.

lcUpsInputTable

lcUpsInputEntry

lcUpsInputLine

The input Line.

lcUpsInputVoltage

The input voltage. (Unit of measure: Volt)

lcUpsOutputFrequency

The current output frequency. (Unit of measure: Hertz)

lcUpsOutputLoad

The current output load percentage.

lcUpsOutputNumLines

The number of output lines utilized in this device. This entry indicates the number of rows in the output table.

lcUpsOutputTable

lcUpsOutputEntry

lcUpsOutputLine

The output Line.

lcUpsOutputVoltage

The output voltage. (Unit of measure: Volt)

lcUpsOutputCurrent

The output current. (Unit of measure: Amp)

lcUpsInverterStatus

The state of the inverter. Unknown is returned if the state can not be determined.

lcUpsAlarms

The current number of alarm conditions.

lcUpsAlarmTable

lcUpsAlarmEntry

lcUpsAlarmId

A unique identifier for an alarm condition. This value must remain constant between agent initializations.

lcUpsAlarmDescr

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.

lcUpsAlarmTime

The value of sysUpTime when the alarm condition occured.

lcUpsTestBattery

Setting this variable to 'start' will initiate the battery test. Setting this variable to 'abort' will stop the battery test if the test is in- progress, otherwise it has no effect. Setting this variable to 'unknown' has no effect. Reading this variable ...

lcUpsTestBatteryStatus

The status of the battery test.

lcUpsControlOutputOffDelay

Setting this object causes the agent to instruct the UPS to turn off the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOffTrap when the countdown ...

lcUpsControlOutputOnDelay

Setting this object causes the agent to instruct the UPS to turn on the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOnTrap when the countdown f ...

lcUpsControlOutputOffTrapDelay

When 'lcUpsControlOutputOffDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOffWarningTrap will be produced and this object will be reset to 0.

lcUpsControlOutputOnTrapDelay

When 'lcUpsControlOutputOnDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOnWarningTrap will be produced and this object will be reset to 0.

lcUpsControlUnixShutdownDelay

Setting this object causes the agent to instruct the UPS to perform a UNIX Shutdown in the indicated number of seconds. The agent counts down the number of seconds until the event will take place. A Unix shutdown is only valid if the UPS is on Battery. ...

lcUpsControlUnixShutdownTrapDelay

When 'lcUpsControlUnixShutdownDelay' reaches a value less than or equal to this object's value, an lcUpsUnixShutdownWarningTrap will be produced and this object will be reset to 0.

lcUpsControlCancelCommands

Setting this variable to 'cancel' will cause the agent to issue instructions to the UPS to cancel all outstanding commands, such as lcUpsControlOutputOff, lcUpsControlOutputOn, lcUpsControlUnixShutdown.

lcUpsControlRebootAgentDelay

Setting this object causes the agent to reboot after the indicated number of seconds have expired. The value will count down until the event takes place. The command can be cancelled by setting lcUpsControlCancleCommand to the value cancel.

lcUpsNominalOutputVoltage

The nominal output voltage. (Unit of measure: volt)

lcUpsNominalInputVoltage

The nominal input voltage. (Unit of measure: volt)

lcUpsNominalOutputFreq

The nominal output frequency. (Unit of measure: Hertz)

lcUpsNominalInputFreq

The nominal input frequency. (Unit of measure: Hertz)

lcUpsNominalOutputVaRating

The nominal Volt-Amp rating.

lcUpsNominalOutputWattsRating

The nominal power rating. (Unit of measure: watt)

lcUpsConfigType

Indicates the UPS topology.

lcUpsConfigBypassInstalled

Indicates if a bypass is installed in the UPS.

lcUpsConfigModuleCount

A number identifying how many multi-module UPS are connected to the System Control Cabinet.

lcUpsConfigAudibleStatus

The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm.

lcUpsConfigLowBattTime

The value of lcUpsBatTimeRemaining at which a lowBatteryWarning condition is declared. (Unit of measure: Minute)

lcUpsConfigAutoRestart

Setting this object will start the output after the indicated number of ticks (1 tick = 10 seconds), including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will disable au ...