LIEBERT-SERIES-4300-UPS-MIB Download

lcUpsIdentManufacturer

The UPS manufacturer.

lcUpsIdentModel

The UPS Model designation.

lcUpsIdentSoftwareVersion

The UPS SNMP Agent software version.

lcUpsIdentSpecific

A reference to MIB definitions specific to the particular UPS being managed. This object is used to locate the product-specific MIB for this device. If this information is not present, its value should be the OBJECT IDENTIFIER { 0 0 }, which is a syntacti ...

lcUpsBatTimeRemaining

The estimated time to depletion of battery charge. (Unit of measure: Minute)

lcUpsBatTemperature

The battery temperature. (Unit of measure: Degree, Centigrade)

lcUpsBatVoltage

The current battery voltage. (Unit of measure: volt)

lcUpsBatCapacity

The current battery capacity in percentage of total available.

lcUpsOutputFrequency

The current output frequency. (Unit of measure: Hertz)

lcUpsOutputLoad

The current output load percentage.

lcUpsOutputNumLines

The number of output lines utilized in this device. This entry indicates the number of rows in the output table.

lcUpsOutputTable

lcUpsOutputEntry

lcUpsOutputLine

The output Line.

lcUpsOutputVoltage

The output voltage. (Unit of measure: Volt)

lcUpsOutputCurrent

The output current. (Unit of measure: Amp)

lcUpsOutputVA

The output volt-amps.

lcUpsOutputWatts

The output power in watts.

lcUpsInverterStatus

The state of the inverter. Unknown is returned if the state can not be determined.

lcUpsInverterTemp

The temperature of the inverter. (Unit of measure: degree, Centigrade)

lcUpsAlarms

The current number of alarm conditions.

lcUpsAlarmTable

lcUpsAlarmEntry

lcUpsAlarmId

A unique identifier for an alarm condition. This value must remain constant between agent initializations.

lcUpsAlarmDescr

A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.

lcUpsAlarmTime

The value of sysUpTime when the alarm condition occured.

lcUpsTestBattery

Setting this variable to 'start' will initiate the battery test. Setting this variable to 'abort' will stop the battery test if the test is in- progress, otherwise it has no effect. Setting this variable to 'unknown' has no effect. Reading this variable ...

lcUpsTestBatteryStatus

The status of the battery test.

lcUpsTestDiag

Setting this variable to 'start' will initiate the diagnostics test. Setting this variable to 'abort' will stop the diagnostics test if the test is in-progress, otherwise it has no effect. Setting this variable to 'unknown' has no effect. Reading this v ...

lcUpsTestDiagStatus

The status of the diagnostics test.

lcUpsControlOutputOffDelay

Setting this object causes the agent to instruct the UPS to turn off the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOffTrap when the countdown ...

lcUpsControlOutputOnDelay

Setting this object causes the agent to instruct the UPS to turn on the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOnTrap when the countdown f ...

lcUpsControlOutputOffTrapDelay

When 'lcUpsControlOutputOffDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOffWarningTrap will be produced and this object will be reset to 0.

lcUpsControlOutputOnTrapDelay

When 'lcUpsControlOutputOnDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOnWarningTrap will be produced and this object will be reset to 0.

lcUpsControlUnixShutdownDelay

Setting this object causes the agent to instruct the UPS to perform a UNIX Shutdown in the indicated number of seconds. The agent counts down the number of seconds until the event will take place. A Unix shutdown is only valid if the UPS is on Battery. ...

lcUpsControlUnixShutdownTrapDelay

When 'lcUpsControlUnixShutdownDelay' reaches a value less than or equal to this object's value, an lcUpsUnixShutdownWarningTrap will be produced and this object will be reset to 0.

lcUpsControlCancelCommands

Setting this variable to 'cancel' will cause the agent to issue instructions to the UPS to cancel all outstanding commands, such as lcUpsControlOutputOff, lcUpsControlOutputOn, lcUpsControlUnixShutdown.

lcUpsControlRebootAgentDelay

Setting this object causes the agent to reboot after the indicated number of seconds have expired. The value will count down until the event takes place. The command can be cancelled by setting lcUpsControlCancleCommand to the value cancel.

lcUpsNominalOutputVoltage

The nominal output voltage. (Unit of measure: volt)

lcUpsNominalInputVoltage

The nominal input voltage. (Unit of measure: volt)

lcUpsNominalOutputVA

The nominal Volt-Amp rating.

lcUpsNominalOutputFreq

The nominal output frequency. (Unit of measure: Hertz)

lcUpsNominalInputFreq

The nominal input frequency. (Unit of measure: Hertz)

ls43cUpsIdentFirmwareVersion

The firmware revision level of the UPS.

ls43cUpsConfigBypassInstalled

Indicates if a bypass is installed in the UPS.

ls43cUpsOnBypass

Indicates that the UPS is currently on bypass.

ls43cUpsBypassFrequency

The current bypass frequency. (Unit of measure: Hertz)

ls43cUpsBypassNumLines

The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.

ls43cUpsBypassTable

ls43cUpsBypassEntry

ls43cUpsBypassLine

The bypass Line.

ls43cUpsBypassVoltage

The bypass voltage. (Unit of measure: Volt)

ls43cUpsBypassCurrent

The bypass current. (Unit of measure: Amp)