LIEBERT-SERIES-600-UPS-MODULE-MIB Download
This MIB defines objects for the Liebert Series 600 UPS SNMP Agents.
IPHost Network Monitor offer an easy way of SNMP monitoring your Liebert Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for LIEBERT-SERIES-600-UPS-MODULE-MIB
- lcUpsIdentManufacturer
- The UPS manufacturer.
- lcUpsIdentModel
- The UPS Model designation.
- lcUpsIdentSoftwareVersion
- The UPS SNMP Agent software version.
- lcUpsIdentSpecific
- A reference to MIB definitions specific to the particular UPS being managed. This object is used to locate the product-specific MIB for this device. If this information is not present, its value should be the OBJECT IDENTIFIER { 0 0 }, which is a syntacti ...
- lcUpsIdentFirmwareVersion
- The firmware revision level of the UPS.
- lcUpsIdentSerialNumber
- The serial number of the UPS.
- lcUpsBatTimeRemaining
- The estimated time to depletion of battery charge. (Unit of measure: Minute)
- lcUpsBatTemperature
- The battery temperature. (Unit of measure: Degree, Centigrade)
- lcUpsBatVoltage
- The current battery voltage. (Unit of measure: volt)
- lcUpsBatCurrent
- The current battery discharging/charging current. (Unit of measure: Amp)
- lcUpsBatCapacity
- The current battery capacity in percentage of total available.
- lcUpsBatTotalDischCounts
- The number of discharges the UPS has experienced.
- lcUpsBatCycleDurationInSeconds
- The total accumulated discharge time in seconds.
- lcUpsBatAmpHours
- The number of amp hours withdrawn from battery.
- lcUpsBatKWhours
- The number of Kilowatt-hours withdrawn from battery.
- lcUpsBatWattHours
- The number of Watt-hours withdrawn from battery.
- lcUpsInputNumLines
- The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
- lcUpsInputTable
- lcUpsInputEntry
- lcUpsInputLine
- The input Line.
- lcUpsInputVoltage
- The input voltage. (Unit of measure: Volt)
- lcUpsInputCurrent
- The input current. (Unit of measure: Amp)
- lcUpsOutputFrequency
- The current output frequency. (Unit of measure: Hertz)
- lcUpsOutputLoad
- The current output load percentage.
- lcUpsOutputNumLines
- The number of output lines utilized in this device. This entry indicates the number of rows in the output table.
- lcUpsOutputTable
- lcUpsOutputEntry
- lcUpsOutputLine
- The output Line.
- lcUpsOutputVoltage
- The output voltage. (Unit of measure: Volt)
- lcUpsOutputCurrent
- The output current. (Unit of measure: Amp)
- lcUpsOutputWatts
- The output power in watts.
- lcUpsInverterStatus
- The state of the inverter. Unknown is returned if the state can not be determined.
- lcUpsAlarms
- The current number of alarm conditions.
- lcUpsAlarmTable
- lcUpsAlarmEntry
- lcUpsAlarmId
- A unique identifier for an alarm condition. This value must remain constant between agent initializations.
- lcUpsAlarmDescr
- A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.
- lcUpsAlarmTime
- The value of sysUpTime when the alarm condition occured.
- lcUpsControlRebootAgentDelay
- Setting this object causes the agent to reboot after the indicated number of seconds have expired. The value will count down until the event takes place. The command can be cancelled by setting lcUpsControlCancleCommand to the value cancel.
- lcUpsNominalOutputVoltage
- The nominal output voltage. (Unit of measure: volt)
- lcUpsNominalInputVoltage
- The nominal input voltage. (Unit of measure: volt)
- lcUpsNominalOutputFreq
- The nominal output frequency. (Unit of measure: Hertz)
- lcUpsNominalOutputVaRating
- The nominal Volt-Amp rating.
- lcUpsNominalOutputWattsRating
- The nominal power rating. (Unit of measure: watt)
- lcUpsOnBypass
- Indicates that the UPS is currently on bypass.
- lcUpsBypassFrequency
- The current bypass frequency. (Unit of measure: Hertz)
- lcUpsBypassNumLines
- The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.
- lcUpsBypassTable
- lcUpsBypassEntry
- lcUpsBypassLine
- The bypass Line.
- lcUpsBypassVoltage
- The bypass voltage. (Unit of measure: Volt)
- lcUpsBypassCurrent
- The bypass current. (Unit of measure: Amp)
- lcUpsConfigType
- Indicates the UPS topology.
- lcUpsConfigBypassInstalled
- Indicates if a bypass is installed in the UPS.
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
