MG-SNMP-UPS-MIB Download

upsmgIdentFamilyName

The UPS family name (e.g. `PULSAR', `COMET', `GALAXY', ...).

upsmgIdentModelName

The UPS model name (e.g. `PSX20', `SV9', ... ).

upsmgIdentRevisionLevel

The UPS revision level.

upsmgIdentFirmwareVersion

The UPS microprocessor firmware version number.

upsmgIdentUserID

The UPS user identification (set by administrator).

upsmgIdentInstallationDate

The UPS installation date in dd/mm/yy format.

upsmgIdentSerialNumber

The UPS manufacturing serial number.

upsmgManagersNum

The number of managers that could manage the UPS.

upsmgManagersTable

The table of managers.

upsmgManagersEntry

The description of a manager entry in the managers table.

mgmanagerIndex

A unique value for each manager. Its value ranges between 1 and the value of upsmgManagersNum.

mgmanagerDeviceNumber

This object is the number of the manager device in the DevicesTable of the Config group. This means that the manager is powered by the UPS. If not the default value is 0.

mgmanagerNMSType

The type of manager according to the NMS platform. We include in the manager class all systems which will be notified by the agent via receiving traps (e.g. basic to complex NMS software).

mgmanagerCommType

The level of communication protocol for that manager. Setting this object to value invalid(2) has the effect of invalidating the corresponding entry in the upsmgManagersTable. It is an implementation-specific matter as to wether the agent removes an inval ...

mgmanagerDescr

A textual string containing information about the manager. (manufacturer and version description).

mgmanagerAddress

The IP address of the manager station receiving traps. The value of this object is meaningful if and only if the value of the relevant mgmanagerCommType object is snmp type.

mgmanagerCommunity

The manager community string.

mgmanagerSeverityLevel

The severity level of traps to be received by this manager.

mgmanagerTrapAck

The manager Trap Acknowledgement status. Setting this object to mgnoack(2) or stdnomg(3) or cpqnoack(5) disables the trap acknowledgement from the related manager. The MG enterprise specific trap should then be sent only once by the agent to this manager ...

upsmgReceptaclesNum

The total number of receptacles controlled by the UPS.

upsmgReceptaclesTable

The table of receptacles that are controlled by the UPS.

upsmgReceptaclesEntry

The description of a receptacle in the table.

mgreceptacleIndex

A unique value for each receptacle. Its value ranges between 1 and the value of upsmgReceptaclesNum.

mgreceptacleLevel

The level of receptacle. Setting this object to value invalid(2) has the effect of invalidating the corresponding entry in the upsmgReceptaclesTable. It is an implementation-specific matter as to wether the agent removes an invalidated entry from the tabl ...

mgreceptacleType

A textual string for the receptacle type.

mgreceptacleIdent

A textual string identification for the user.

mgreceptacleState

The ON/OFF status of the receptacle.

mgreceptacleReceptacle

The receptacle number of the second level receptacle father. The value of this object is meaningful if and only if the value of the relevant mgreceptacleType object is related to a two-level receptacle class. Otherwise the default value is 0.

mgreceptaclePowerCons

The volt-ampere rating of the receptacle. The value of this object is meaningful if and only if the value of the relevant mgreceptacleType object is related to a two-level receptacle class. Otherwise the default value is 0.

mgreceptacleOverload

The overload status of the receptacle. The value of this object is meaningful if and only if the value of the relevant mgreceptacleType object is related to a two-level receptacle class. Otherwise the default value is 0.

mgreceptacleAutonomy

The receptacle autonomy. The value of this object is meaningful if and only if the value of the relevant mgreceptacleType object is related to a two-level receptacle class. Otherwise the default value is 0.

upsmgConfigBatteryInstalled

The battery installed status.

upsmgConfigNominalBatteryVoltage

The nominal battery voltage.

upsmgConfigNominalBatteryTime

The full load battery autonomy time.

upsmgConfigNominalRechargeTime

The recharge time to go from low battery cut off to full charge at full load.

upsmgConfigMinRechargeLevel

The minimum battery level required to supply power on the loads after low battery condition turn off and restart on main return.

upsmgConfigMaxRechargeTime

The maximum time delay of battery recharge before supply power to the loads.

upsmgConfigLowBatteryTime

To set remaining time value for low battery condition.

upsmgConfigLowBatteryLevel

To set battery level value for low battery condition.

upsmgConfigAutoRestart

The automatic restart enabling status.

upsmgConfigShutdownTimer

To set ups shutdown timer from on battery condition.

upsmgConfigSysShutDuration

To set ups shutdown delay (Sn delay).

upsmgConfigVARating

The UPS nominal VA rating.

upsmgConfigLowTransfer

The low voltage transfer point.

upsmgConfigHighTransfer

The high voltage transfer point.

upsmgConfigOutputNominalVoltage

The nominal output voltage.

upsmgConfigOutputNominalCurrent

The nominal output current.

upsmgConfigOutputNomFrequency

The nominal output frequency.

upsmgConfigByPassType

The UPS by pass switch type.

upsmgConfigAlarmAudible

To set audible alarm status.

upsmgConfigAlarmTimeDelay

To set audible alarm time delay.

upsmgConfigDevicesNum

The number of devices that are powered by the UPS.

upsmgConfigDevicesTable

The table of devices that are powered by the UPS.

upsmgConfigDevicesEntry

The description of a device entry in the devices table.

mgdeviceIndex

A unique value for each device. Its value ranges between 1 and the value of upsmgDevicesNum.

mgdeviceReceptacleNum

The receptacle number of the device plugged into the UPS. This value gives index entry in the ReceptaclesTable object of the Receptacle group. A value of 0 invalidates the entry in the DevicesTable.

mgdeviceIdent

A textual string for device user identification.

mgdeviceVaRating

The volt-ampere rating of the device plugged into the UPS.

mgdeviceSequenceOff

To set the device position in the remote shutdown sequence.

mgdeviceSequenceOn

To set the device position in the remote reboot sequence.

mgdeviceShutdownDuration

To set the duration from start of computer shut-down to complete.

mgdeviceBootUpDuration

To set the duration from start of computer boot-up to complete.

upsmgConfigReceptaclesTable

The table of receptacles.

upsmgConfigReceptaclesEntry

The description of a receptacle entry in the table.

mgreceptacleIndexb

A unique value for each receptacle. Its value ranges between 1 and the value of upsmgReceptaclesNum.

mgreceptacleStateTurnOn

Default return state at turn on.

mgreceptacleStateMainReturn

Default return state on main return.

mgreceptacleStateDischarge

Default return state on main return from battery discharge.

mgreceptacleShutoffLevel

Battery level for starting shutoff sequence.

mgreceptacleShutoffTimer

Time delay from on battery for starting shutoff sequence.

mgreceptacleRestartLevel

Battery level for starting restart sequence.

mgreceptacleRestartDelay

Time delay for starting restart sequence.

mgreceptacleShutdownDuration

Maximum Shutdown Duration for systems powered by this plug.

mgreceptacleBootUpDuration

Maximum Reboot Duration for systems powered by this plug.

upsmgConfigExtAlarmNum

The number of environ external alarm, value is between 8 and 32..

upsmgConfigExtAlarmTable

The table of environmental external alarms.

upsmgConfigExtAlarmEntry

The description of an external alarm in the table.

mgextAlarmIndex

A unique value for each external alarm. Its value ranges between 1 and the value of upsmgConfigExtAlarmNum.

mgextAlarmUID

A textual string for alarm state user identification.

upsmgConfigEmergencyTestFail

The emergency condition status on Battery test fail.

upsmgConfigEmergencyOnByPass

The emergency condition status on By Pass.

upsmgConfigEmergencyOverload

The emergency condition status on overload.

upsmgConfigControlDayTable

The table of daily on/off time.

upsmgConfigControlDayEntry

The description of a daily on/off time schedule in the table.

mgcontrolDayIndex

The day index. It is a number between 1 and 7, 1 for Sunday, 2 for Monday, ...

mgcontrolDayOn

To set daily power on time. Any value greater than 86400 is to disable the Day On.

mgcontrolDayOff

To set daily power off time. Any value greater than 86400 is to disable the Day Off.

upsmgConfigLowBooster

To set UPS booster low threshold.

upsmgConfigHighBooster

To set UPS booster high threshold.

upsmgConfigLowFader

To set UPS fader low threshold.

upsmgConfigHighFader

To set UPS fader high threshold.

upsmgConfigEnvironmentTable

The table containing the configuration of the environment sensor.

upsmgConfigEnvironmentEntry

The description of an entry in the table.

upsmgConfigSensorIndex

The sensor index, ranging from 1 to upsmgEnvironmentNum.

upsmgConfigSensorName

The sensor user-friendly name.

upsmgConfigTemperatureLow

The low temperature threshold in unit 0.1 Cel.

upsmgConfigTemperatureHigh

The high temperature threshold in unit 0.1 Cel.

upsmgConfigTemperatureHysteresis

The temperature hysteresys used for threshold test in unit 0.1 Cel.

upsmgConfigHumidityLow

The low humidity threshold in unit 1 %.

upsmgConfigHumidityHigh

The high humidity threshold in unit 1 %.

upsmgConfigHumidityHysteresis

The humidity hysteresys used for threshold test in unit 1 %.

upsmgConfigInput1Name

The Input #1 user-friendly name.

upsmgConfigInput1ClosedLabel

The Input #1 label for closed position.

upsmgConfigInput1OpenLabel

The Input #1 label for open position.

upsmgConfigInput2Name

The Input #2 user-friendly name.

upsmgConfigInput2ClosedLabel

The Input #2 label for closed position.

upsmgConfigInput2OpenLabel

The Input #2 label for open position.

upsmgBatteryRemainingTime

The time remaining actual charge vs actual load (dynamic).

upsmgBatteryLevel

The battery level as a percentage of charge.

upsmgBatteryRechargeTime

The actual operational battery recharge time to set point equal to upsmgConfigRechargeLevel. This value is computed from upsmgConfigRechargeLevel (level to reach), upsmgBatteryLevel (the actual reached level) and the UPS charge rate.

upsmgBatteryRechargeLevel

The actual value of the battery recharge level that will be reached during the time delay necessary to restart after power returns. This value is computed from upsmgConfigRechargeTime (the delay), upsmgBatteryLevel (the actual level) and the UPS charge ra ...

upsmgBatteryVoltage

The actual battery voltage.

upsmgBatteryCurrent

The actual battery current.

upsmgBatteryTemperature

The battery temperature.

upsmgBatteryFullRechargeTime

The battery full recharge time (from 0 to 100 percent) at current load.

upsmgBatteryFaultBattery

The battery fault status.

upsmgBatteryNoBattery

The UPS has no Battery status.

upsmgBatteryReplacement

The UPS Battery to be replaced status.

upsmgBatteryUnavailableBattery

The UPS Battery is unavailable status.

upsmgBatteryNotHighCharge

The UPS Battery quit high condition status.

upsmgBatteryLowBattery

The battery low status.

upsmgBatteryChargerFault

The UPS Battery is not charging status.

upsmgBatteryLowCondition

The UPS is at low condition status.

upsmgBatteryLowRecharge

The UPS Battery is not recharged status.

upsmgInputPhaseNum

The number of input phases.

upsmgInputPhaseTable

The table of input phases.

upsmgInputPhaseEntry

The description of an input phase.

mginputIndex

The input phase voltage index. It is a number between 1 and upsmgInputPhaseNum.

mginputVoltage

The input phase voltage.

mginputFrequency

The input phase frequency.

mginputMinimumVoltage

The input phase minimum voltage over the last minute.

mginputMaximumVoltage

The input phase maximum voltage over the last minute.

mginputCurrent

The input phase current.

upsmgInputBadStatus

The utility power bad voltage or bad frequency status.

upsmgInputLineFailCause

The utility power failure cause: no(1) is for no utility failure, outoftolvolt(2) is for voltage out of tolerance, outoftolfreq(3) is for frequency out of tolerance, utilityoff(4) is for no voltage at all.

upsmgOutputPhaseNum

The number of output phases.

upsmgOutputPhaseTable

The table of output phases.

upsmgOutputPhaseEntry

The description of an output phase.

mgoutputPhaseIndex

The output phase voltage index. It is a number between 1 and upsmgOutputPhaseNum.

mgoutputVoltage

The output phase voltage.

mgoutputFrequency

The output phase frequency.

mgoutputLoadPerPhase

The output load per phase.

mgoutputCurrent

The output phase current.

upsmgOutputOnBattery

The UPS on battery / on main status.

upsmgOutputOnByPass

The UPS on bypass status.

upsmgOutputUnavailableByPass

The by pass unavailable status.

upsmgOutputNoByPass

The UPS bypass installed status.

upsmgOutputUtilityOff

The UPS utility off status.

upsmgOutputOnBoost

The UPS on booster status.

upsmgOutputInverterOff

The UPS Inverter on / off status.

upsmgOutputOverLoad

The output over load status.

upsmgOutputOverTemp

The ups over temperature status.

upsmgOutputOnBuck

The UPS on fader status.

upsmgEnvironAmbientTemp

The ambient temperature.

upsmgEnvironAmbientHumidity

The ambient humidity.

upsmgEnvironExtAlarmTable

The table of external alarms.

upsmgEnvironExtAlarmEntry

The description of an external alarm.

mgalarmNum

The external alarm number. A number between 1 and upsmgConfigExtAlarmNum.

mgalarmState

The external alarm state (active or inactive).

upsmgEnvironSensorNum

The sensor unit number (0 to 4).

upsmgEnvironSensorTable

The table of sensor units.

upsmgEnvironSensorEntry

The description of a sensor unit.

mgsensorNum

The unit number. A number between 1 and 4.

mgsensorTemp

The measured temperature of the unit.

mgsensorHumidity

The measured humidity of the unit.

upsmgEnvironmentNum

Number of Environment sensor connected.

upsmgEnvironmentSensorTable

The table containing the measurements and alarms made by Environment sensor units.

upsmgEnvironmentSensorEntry

The description of an entry in the measurement table.

upsmgEnvironmentIndex

The sensor index, ranging from 1 to upsmgEnvironmentNum.

upsmgEnvironmentComFailure

The sensor communication failure : yes(1), no(2).

upsmgEnvironmentTemperature

The temperature measurement in unit 0.1 Cel.

upsmgEnvironmentTemperatureLow

Temperature is below low theshold : yes(1), no(2).

upsmgEnvironmentTemperatureHigh

Temperature is above high threshold : yes(1), no(2).

upsmgEnvironmentHumidity

The humidity measurement in unit 0.1 %.

upsmgEnvironmentHumidityLow

Humidity is below low threshold : yes(1), no(2).

upsmgEnvironmentHumidityHigh

Humidity is above high threshold : yes(1), no(2).

upsmgEnvironmentInput1State

State of Input#1 : closed(1), open(2).

upsmgEnvironmentInput2State

State of Input#2 : closed(1), open(2).

upsmgControlReceptaclesTable

The table of receptacles.

upsmgControlReceptaclesEntry

The description of a receptacle entry in the table.

mgreceptacleIndexc

A unique value for each receptacle. Its value ranges between 1 and the value of upsmgReceptaclesNum.

mgreceptacleOnDelay

Turn on UPS receptacle w/delay=?.

mgreceptacleOnCtrl

The receptacle control on action.

mgreceptacleOnStatus

The receptacle control on status.

mgreceptacleOffDelay

Turn off UPS receptacle w/delay=?.

mgreceptacleOffCtrl

The receptacle control off action.

mgreceptacleOffStatus

The receptacle control off status.

mgreceptacleToggleDelay

Turn off then on UPS receptacle w/delay=?.

mgreceptacleToggleCtrl

The receptacle control toggle action.

mgreceptacleToggleStatus

The receptacle control toggle status.

mgreceptacleToggleDuration

Turn off then on UPS receptacle w/duration=?.

upsmgControlDayOff

The schedule off control object. Default value is none(8). Value 1 means to start scheduled off on Sunday, value 2 to start scheduled off on Monday, and so on.

upsmgControlDayOn

The schedule on control object. Default value is none(8). Value 1 means to start scheduled on on Sunday, value 2 to start scheduled on on Monday, and so on. This object is meaningfull only for those agent that do not include internal clock. In such a case ...

upsmgTestBatterySchedule

The automatic battery test schedule.

upsmgTestDiagnostics

To run self test diagnostics.

upsmgTestDiagResult

The automatic test diagnostic result.

upsmgTestBatteryCalibration

To run battery test calibration.

upsmgTestLastCalibration

The last battery calibration test date.

upsmgTestIndicators

To run UPS indicators test.

upsmgTestCommandLine

To send ASCII command line to UPS.

upsmgTestCommandReady

To advise UPS that command line has been prepared.

upsmgTestResponseLine

To get ASCII protocol response from UPS.

upsmgTestResponseReady

To advise agent that response line has been received.

upsmgTestBatteryResult

The test battery result: msuccess(1) is for manual battery test success, ssuccess(3) is for scheduled battery test success, mfailed(2) is for manual battery test failed, sfailed(4) is for scheduled battery test failed.

upsmgAgentIpaddress

The ip address that NMS can identify the managed device

upsmgAgentSubnetMask

Internet address subnet mask

upsmgAgentDefGateway

The default gateway that allow device managed through routers

upsmgAgentBaudRate

the serial port communication speed. only 2400, 4800, and 9600 allowed

upsmgAgentPollRate

The frequency that proxy agent polls the connected UPS in ASCII protocol. (unit : second)

upsmgAgentType

The type of agent.

upsmgAgentTrapAlarmDelay

The interval for the Trap packet retransmission, while the TRAP Acknowledge is implemented and the ack is received within the interval.

upsmgAgentTrapAlarmRetry

The retry count for retransmitting Trap packet while the TRAP acknowledge is implemented.

upsmgAgentReset

The variable initiates reset operation in agent software, ie. warm start. write reset(1) to any one of UPS MIB array, will result in the same reset operation.

upsmgAgentFactReset

The variable initiates reset operation in agent software, ie. warm start, and load default data (Factory setting) to EEPROM and to runtime parameters associated with the UPS.

upsmgAgentMibVersion

The version of the MIB implemented in agent.

upsmgAgentFirmwareVersion

The agent firmware version.

upsmgAgentCommUPS

The status of communication between agent and ups. Even value means no communication, and odd value means a certain level of communication with devices daisy-chained on the serial port. The value is the following: 1000*NSE + 100*NSW + 10*UPSW + UPST with ...

upsmgAgentTrapAck

The last Trap number that has been received by UM-View.

upsmgAgentAutoLearning

The enabled/disabled configuration of the Auto Learning process of the agent, default value is yes(1) e.g. enabled.

upsmgAgentBootP

The enabled/disabled configuration of the BootP process, default value is yes(1) e.g. enabled.

upsmgAgentTFTP

The enabled/disabled configuration of the TFTP process, default value is no(2) e.g. disabled.

upsmgAgentTrapSignature

The signature of the trap acknowledged by a manager.

upsmgRemoteOnBattery

An object to inform an ups-less agent that the remote UPS is on autonomy. This object could be set by a management application.

upsmgRemoteIpAddress

An object to give the IP address of the agent managing the remote UPS. This object could be read by managers to perform management of receptacle dependencies between two different agents.