MODULES-MIB Download

ethAgTable

Table of attributes which define configuration characteristics for chassis SNMP agents which use Ethernet as in-band management protocol.

ethAgEntry

An entry in the table, containing data about a single Ethernet agent.

ethAgId

Index which identifies the Ethernet agent for which the current entry provides information.

ethAgPerfBusSelection

Attribute describing the bus attached to the performance data collection hardware on those agent hardware implementations which support configuration management on multi-Ethernet bus enclosures, but performan- ce data collection on a single bus.

ethGroupTable

Table of attributes which define configuration characteristics for Ethernet modules.

ethGroupEntry

An entry in the table, containing data about a single Ethernet module (group).

ethGroupId

Index which identifies the group inside the chassis for which this entry contains information. Equals the number of the slot by which the group is accessed. This value is never greater than chNumberOfSlots.

ethGroupFIFO

Value ON of this attribute describes an internal FIFO error sensed by the internal hardware mechanism of a repeater.

ethGroup10BTPlus

Value ON of this attribute defines activation of the 10BaseTPlus mode - a proprietary extension of the 10BaseT standard.

ethGroupIntPortsRedundancy

Value ON of this attribute defines a redundancy (backup) relationship between internal ports 1 and 2 on a module.

ethGroupBackboneMode

Value On of this attribute defines Backbone Mode of a sensor. Internal ports are enabled and the information path goes straightly from external port to internal bus, via corresponding internal port.

ethGroupFOIRLPlusMode

Value On of this attribute defines FOIRL of a sensor. When this attribute has value ON, FOIRL Plus mode is enabled, while value OFF indicates stan- dard FOIRL mode.

ethGroupWrongPortSelection

A value ON of this attribute warns of incorrect selection of enabled ports on sensors which impose restrictions on this configura- tion (e.g. integrated local bridges.)

ethGroupBackupBus

Defines the common secondary bus for Ethernet modules with bus redundancy defined at port level.

ethGroupSingleBusMode

Value 'on of this attribute defines bus-star mode for cards supporting this type of configuration.

ethGroupSpecificOID

This attribute provides the OID of another group containing additional more specific information regarding this instance.

ethGroup10FBPlus

This variable enables/disables 10BaseFB plus mode.

ethGroupMasterClock

This attribute pertains to the SH-E16 chassis and defines the hub in the stack that generates the clock.

ethGroupIdleTrx

This attribute is relevant to the LE-120Q/SQ modules and when set to 'off' after port disable terminates also light propagation (for redundancy tests).

ethGroupTotalFrames

The total number of frames of valid frame length that have been received on the ports in this group and for which the FCSError and CollisionEvent signals were not asserted. This statistic provides one of the parameters necessary for obtaining the packet e ...

ethGroupTotalOctets

The total number of octets contained in the valid frames that have been received on the ports in this group. This counter is the summation of the values of the ethPortReadableOctets counters for all of the ports in the group. This statistic provides an i ...

ethGroupTotalErrors

The total number of errors which have occurred on all of the ports in this group. This counter is the summation of the values of the ethPortTotalErrors counters for all of the ports in the group. This item is a Repeater MIB counter.

ethGroupBridgeMode

This attribute defines between which buses/ports the IELB bridge is bridging.

ethGroupBroadcastPkts

The total number of good packets received that were directed to the broadcast address, through this ports group.

ethGroupMulticastPkts

The total number of good packets received that were directed to a multicast address, through this ports group. Note that this number does not include packets directed to the broadcast address.

ethPortTable

ethPortEntry

ethPortGroupId

Id of the group to which the port belongs.

ethPortId

Unique Id of the port in the ethPortTable.

ethPortFunctionalStatus

The value of this attribute reflects the functional status of synchronous ports. Note that it is not mandatory that all ports support all the enumerated states. ok(1) - fully functional port, transmitting and receiving packets. rld(2) - receive link down ...

ethPortManPart

Setting the value of this attribute to ON activates the manual partition mechanism at the port level. Setting the value of this attribute to OFF cancels the partition mechanism. The segment may reconnect after the reception of 32 packets. Attribute vaild ...

ethPortJabber

Value ON of this attribute reflects jabber transmitted to the port by the hardware of a repeater or transceiver, as a result of collisions detected on the port. Valid for all modules in the LE-10 and LE-15 families.

ethPortNoAUILoop

Value ON of this attribute indicates that a No AUI Loop fault condition was detected on an AUI repeater port. Valid for LE-10C family of modu- les.

ethPortMJLP

Value ON of this attribute describes an internal MJLP (MAU Jabber Lockup Protection) error sensed by the internal hardware mechanism of a repeater. This mechanism is activated to protect the repeater ports from a jabber condition (excessive long transmis ...

ethPortFIFO

Value ON of this attribute describes an internal FIFO error sensed by the internal hardware mechanism of a repeater. Valid for LE140XTF.

ethPortAutoPartitionState

The AutoPart condition indicates that the port is currently partitioned by the auto-partition protection mechanism.

ethPortSQETest

Settable attribute which allows activation of SQE test for integrated transceivers.

ethPortLastSourceAddr

Ethernet source address of the last readable frame received by this port. The value of this item may be set to 000000 (a string of 6 zeros) by a management console, but not to any other value.

ethPortUserStatus

Attribute defining the connection of a port to a single Ethernet source or to a multi-source (segment or star).

ethPortMainBusSelection

On cards with port-level redundancy, defines the main bus for each port instance as selected by user.

ethPortTraffic

Counter for the number of bits received on this port in frames with legal length information.

ethPortFramesReceivedOK

A representation of the total number of frames of legal length that have not been corrupted in transmission. These frames can be encoded and decoded by the commonly available MACs and provide a measure of the network bandwidth being used. The number does ...

ethPortRunts

This counter is incremented by one for each CarrierEvent on this port that meets one of the following two conditions. Only one test need be made. a) The ActivityDuration is greater than ShortEventMaxTime and less than ValidPacketMinTime and the Collisio ...

ethPortPacketErrors

Counter for the number of frames with errors detected on the port by the agent hardware. This generic port error comprises too long packets, CRC and alignment errors.

ethPortSpecificOID

This attribute provides the OID of another group containing additional more specific information regarding this instance.

ethPortCollisions

This counter is incremented by one for any CarrierEvent signal on any port for which the CollisionEvent signal on this port is also asserted. The approximate minimum time for rollover of this counter is 16 hours. Relevant for MPR and HIMIB modules. REFERE ...

ethPortPartitions

This counter is incremented by one for each time the repeater has automatically partitioned this port. The conditions that cause port partitioning are specified in the partition state machine in Section 9 [IEEE 802.3 Std]. They are not differentiated he ...

ethPortPygmys

The number of pygmys observed on a specified port. The pygmy is a short event. This counter is incremented by one for each CarrierEvent on this port with ActivityDuration less than ShortEventMaxTime. ShortEventMaxTime is greater than 74 bit times and les ...

ethPortJabberCounter

Counter for the number of local jabbers detected on a specific port (LE-115Q).

ethPortCoupling

Indication of port's coupling method in Ethernet transceiver modules (LE-115Q). The coupling methode can be set on board, using specific jumpers.

ethPortPolarity

This item defines the polarity state of the connection to LE-240XTC and LE-280XT ports. If the wires are crossed, the value is crossed(2), otherwise ok(1).

ethPortReadableFrames

This object is the number of frames of valid frame length that have been received on this port. This counter is incremented by one for each frame received on this port whose OctetCount is greater than or equal to minFrameSize and less than or equal to max ...

ethPortReadableOctets

This counter is the number of octets contained in valid frames that have been received on this port.It is incremented for each frame received on this port which has been determined to be a readable frame (including FCS octets but excluding framing bits an ...

ethPortFCSErrors

This counter is incremented by one for each frame received on this port with the FCSError signal asserted and the FramingError and CollisionEvent signals deasserted and whose OctetCount is greater than or equal to minFrameSize and less than or equal to ma ...

ethPortAlignmentErrors

This counter is incremented by one for each frame received on this port with the FCSError and FramingError signals asserted and CollisionEvent signal deasserted and whose OctetCount is greater than or equal to minFrameSize and less than or equal to maxFra ...

ethPortFramesTooLong

This counter is incremented by one for each frame received on this port whose OctetCount is greater than maxFrameSize (Ref: 4.4.2.1, IEEE 802.3 Std). The approximate minimum time for rollover of this counter is 61 days. This object is a Repeater MIB count ...

ethPortLateEvents

This counter is incremented by one for each CarrierEvent on this port in which the CollIn(X) variable transitions to the value SQE (Ref:9.6.6.2, IEEE 802.3 Std) while the ActivityDuration is greater than the LateEventThreshold. Such a CarrierEvent is cou ...

ethPortVeryLongEvents

This counter is incremented by one for each CarrierEvent on this port whose ActivityDuration is greater than the MAU Jabber Lockup Protection timer TW3 (Ref: 9.6.1 & 9.6.5, IEEE 802.3 Std). Other counters may be incremented as appropriate. This object is ...

ethPortDataRateMismatches

This counter is incremented by one for each frame received on this port that meets all of the following conditions: a) The CollisionEvent signal is not asserted. b) The ActivityDuration is greater than ValidPacketMinTime. c) The frequency (data rate) is d ...

ethPortTotalErrors

The total number of errors which have occurred on this port. This counter is the summation of the values of other error counters (for the same port), namely: ethPortFCSErrors, ethPortAlignmentErrors, ethPortFrameTooLongs, ethPortShortEvents, ethPortLateE ...

ethPortSourceAddrChanges

This counter is incremented by one for each time that the last source address of frames entering this port has changed. This may indicate whether a link is connected to a single DTE or another multi-user segment. The approximate minimum time for rollover ...

ethPortOperStatus

This object indicates the port's operational status. The operational(1) status indicates that the port is enabled and working, even though it might be auto-partitioned.

ethPortBroadcastPkts

The total number of good packets received that were directed to the broadcast address.

ethPortMulticastPkts

The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address.

ethIntPortTable

ethIntPortEntry

ethIntPortGroupId

ID of the group to which the internal port belongs.

ethIntPortId

ID of the internal port in the ethIntPortTable.

ethIntPortPartition

This condition indicates that the internal port is currently partitioned from the bus by the auto-partition protection mechanism.

ethIntPortJabber

Value ON of this attribute reflects jabber being transmitted to the bus by the hardware of a repeater, as a result of collisions detected on the internal bus of the enclosure. This situation is similar to MJLP as defined by the Repeater Management standa ...

ethIntPortBackedUp

Indicates that internal port is part of a redundancy scheme.

ethBusPerfTable

ethBusPerfEntry

ethBusPerfAgId

ID of the agent in the ethBusPerfTable.

ethBusPerfId

ID of the bus in the ethBusPerfTable.

ethBusTrafficBuffer

Record of traffic for the last second with a resolution of 100 msec. The traffic is expressed in percents of the maximum Ethernet traffic and each record contains 10 readings, in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ).

ethBusTrafficThresh

Traffic threshold value. When exceeded, a trap is send to the management console. Expressed in percents of the maximum Ethernet traffic, in the range 1..20, expressed on a log(10) scale.

ethBusPeakTraffic

Maximal traffic value since last reset of hub or relay. Expressed in per- cents of the maximum Ethernet traffic, in the range 1..20, expressed on log(10) scale. The write access is reserved for resetting the value of the peak.

ethBusTotalCollisions

Counter incremented every time the hub enters a condition caused by simultaneous transmission and detection of external activity on one or more of its ports.

ethBusTotalPackets

Counter for number of packets (good and errors) detected on the Ethernet bus.

ethBusTotalErrors

Counter for number of errors detected on the Ethernet bus. Does not take into account the collisions.

ethBusTraffic

Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Ethernet traffic in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ).

ethBusUtilization

Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Ethernet traffic.

ethBusPeakUtilization

Maximal traffic value since last reset of agent. Expressed in percents of the maximum effective Ethernet traffic.

ethBusThresholdStatus

This item is a bitmap that defines the threshold status of the bus, in relation to the alarmPolicyTable. If the bus is monitored by the agent according to policy number x in the alarmPolicyTable, and the threshold condition has occured, then the bit #x in ...

ethBusClockTable

ethBusClockEntry

ethBusClockBusId

ID of the bus in the ethBusClockTable.

ethBusClockId

ID of the clock in the ethBusClockTable.

ethBusClockTestResult

Values clockFailure(2) and busFailure(3) define the faulty status for clock tests. The test is performed by LCL100 module.

fethPortTable

Table of descriptive, status, performance and error information about the ports.

fethPortEntry

An entry in the table, containing information, performance and error statistics about a single port.

fethPortGroupId

Id of the group to which the port belongs.

fethPortId

Unique Id of the port in the ethPortTable.

fethPortFunctionalStatus

The value of this attribute reflects the functional status of LANNET 100BaseTX port. Here is the set possible states: ok(1)- fully functional port, transmitting and receiving packets. rld(2) - receive link down (Link Test Failure) condition on the port - ...

fethPortFIFO

Value ON of this attribute describes an internal FIFO error sensed by the internal hardware mechanism of a the port.

fethPortOperStatus

This object indicates the port's operational status. The operational(1) status indicates that the port is enabled and working, even though it might be auto-partitioned.

fethPortAutoPartitionState

The AutoPart condition indicates that the port is currently partitioned by the auto-partition protection mechanism.

fethPortFramesReceived

A representation of the total number of frames received by the port from the line. The number includes all frames received even those with RxError or alignment errors or those that had been corrupred in transmission.

fethPortFramesTransmitted

A representation of the total number of frames transmitted by the port to the line. The number includes all frames transmitted.

fethPortTotalErrors

The total number of errors which have occurred on this port. This counter is the summation of the values of other error counters (for the same port), namely: fethPortFCSErrors, fethPortAlignmentErrors, fethPortFrameTooLongs, fethPortShortEvents, fethPort ...

fethPortFramesTransmittedOK

A representation of the total number of frames of legal length that have not been corrupted in transmission that transmitted by the port to the line. These frames can be encoded and decoded by the commonly available MACs. Not supported by LFE1008.

fethPortCollisionFrames

This counter is incremented by one for any CarrierEvent signal on any port for which the CollisionEvent signal on this port is also asserted.

fethPortAlignmentErrors

This counter is incremented by one for each frame received on this port with the FCSError and FramingError signals asserted and CollisionEvent signal deasserted and whose OctetCount is greater than or equal to minFrameSize and less than or equal to maxFra ...

fethPortRxErrors

The total number of received frames with error code violation or dose not terminate correctlly.

fethPortReadableFrames

This object is the number of frames of valid frame length that have been received on this port. This counter is incremented by one for each frame received on this port whose OctetCount is greater than or equal to minFrameSize and less than or equal to max ...

fethPortUpper32ReadableOctets

This object is the number of octets contained in valid frames that have been received on this port. This counter is incremented by OctetCount for each frame received on this port which has been determined to be a readable frame (i.e., including FCS octets ...

fethPortLower32ReadableOctets

This object is the number of octets contained in valid frames that have been received on this port. This counter is incremented by OctetCount for each frame received on this port which has been determined to be a readable frame (i.e., including FCS octets ...

fethPortFCSErrors

This counter is incremented by one for each frame received on this port with the FCSError signal asserted and the FramingError and CollisionEvent signals deasserted and whose OctetCount is greater than or equal to minFrameSize and less than or equal to ma ...

fethPortFrameTooLongs

This counter is incremented by one for each frame received on this port whose OctetCount is greater than maxFrameSize (Ref: 4.4.2.1, IEEE 802.3 Std). If fethPortFrameTooLongs is incremented then neither the fethPortAlignmentErrors nor the fethPortFCSError ...

fethPortShortEvents

This counter is incremented by one for each CarrierEvent on this port with ActivityDuration less than ShortEventMaxTime. ShortEventMaxTime is 84 bits (21 nibbles). Note: shortEvents may indicate externally generated noise hits which will cause the repea ...

fethPortRunts

This counter is incremented by one for each CarrierEvent on this port that meets one of the following two conditions. Only one test need be made. a) The ActivityDuration is greater than ShortEventMaxTime and less than validPacketMinTime and the Collisi ...

fethPortLateEvents

This counter is incremented by one on entering the Collision Count Increment state of the partition state diagram (fig 27-8) while the ActivityDuration is greater than the LateEvent- Threshold. Such a CarrierEvent is counted twice, as both collision and a ...

fethPortVeryLongEvents

This counter is incremented by one on entry to the Rx Jabber state of the receiver timer state diagram (fig 27-7). Other counters may be incremented as appropriate. REFERENCE Reference IEEE Draft Std 802.3u/D4 Rptr Mgt, 30.4.3.1.13, aVeryLongEvents. Refe ...

fethPortDataRateMismatches

This counter is incremented by one for each frame received on this port that meets all of the following conditions: a) the Collision Count Increment state of the partition state diagram (fig 27-8) has not been entered. b) The ActivityDuration is greate ...

fethPortAutoPartitions

This counter is incremented by one on entry to the Partition Wait state of the partition state diagram (fig 27-8). REFERENCE Reference IEEE Draft Std 802.3u/D4 Rptr Mgt, 30.4.3.1.14, aAutoPartitions. Reference IETF 100Base-T Repeater MIB, rptr100MonitorPo ...

fethPortSymbolErrors

This counter is incremented by one each time when valid length packet was received at the port and there was at least one occurrence of an invalid data symbol. This can increment only once per valid carrier event. A collision presence at any port of the r ...

fethPortLastSourceAddress

This object is the SourceAddress of the last readable frame (i.e., counted by fethPortReadableFrames) received by this port. If no frames have been received by this port since the agent began monitoring the port activity, the agent shall return a string ...

fethPortSourceAddrChanges

This counter is incremented by one for each time that the fethPortLastSourceAddress attribute for this port has changed. This may indicate whether a link is connected to a single DTE or another multi-user segment. The approximate minimum time for rollover ...

fethPortMode

The mode of the port. halfDuplex(1)- standard mode, usually for segments. fullDuplex(2)- standard mode, usually for servers. fullDuplexAndFlowControl(3)- the module transmits Flow Control symbols to the line between two HUBs in order to control the flow ...

fethPortLinkRedundancyMode

This item is relevant for modules which include redundant links. This item enables/disables the Redundancy mechanism. When enabled, the Sensor will alternately switch between the main and secondary ports/links, upon a predefined failure indication. See al ...

fethPortLinkRedundancyStatus

This item is relevant for ports which includes redundant links. This item indicates which of the links is active. Default value=firstLinkActive(1).

fethPortDormantLinkFunctionalStatus

The value of this attribute reflects the functionality status of the dormant link, in modules such as LEB-200, which have link redundancy capability. Note that the Main Link functionality status is still reflected by the fethPortFunctionalStatus item as u ...

fethPortUpper32TransmittedOctets

This object is the number of octets contained in valid frames that have been transmitted on this port. This counter is incremented by OctetCount for each frame transmitted on this port which has not been encountered with a collision event. This statisti ...

fethPortLower32TransmittedOctets

This object is the number of octets contained in valid frames that have been transmitted on this port.This counter is incremented by OctetCount for each frame transmitted on this port which has not been encountered with a collision event. This statistic ...

fethPortBroadcastReceivedFrames

This object is the number of Broadcast readable frames that have been Received on this port.

fethPortMulticastReceivedFrames

This object is the number of Multicast readable (good) frames that have been Received on this port.

fethPortEnablePHY

This item is relevant for ports which include redundant links (such as LEB200). This item is not valid and has no effect when the fethPortLinkRedundancyMode=enable(1). This item determines and indicates the active PHY in case that fethPortLink ...

fethGroupTable

Table of descriptive, status, performance and error information about the groups of fast ethernet ports.

fethGroupEntry

An entry in the table, containing information, total performance and error statistics for a single group of ports. Regular retrieval of the information in this table provides a means of tracking the performance and health of the networked devices attach ...

fethGroupId

This object identifies the group within the repeater for which this entry contains information. This value is never greater than fethRepeaterGroupCapacity. REFERENCE Reference IEEE Draft Std 802.3u/D4 Rptr Mgt, 30.4.2.1.1, aGroupID. Reference IETF 100Base ...

fethGroupOperStatus

An object that indicates the operational status of the group. A status of notPresent(4) indicates that the group is temporarily or permanently physically and/or logically not a part of the repeater (Stand Alone). A status of operational(2) indicates that ...

fethGroupUtilization

Utilization of the network, expressed in percentage of the maximum traffic possible ( 100Mbps)

fethGroupTotalFrames

The total number of frames of valid frame length that have been received on the ports in this group and for which the FCSError and CollisionEvent signals were not asserted. This counter is the summation of the values of the fethPortReadableFrames counter ...

fethGroupUpper32TotalOctets

The total number of octets contained in the valid frames that have been received on the ports in this group. This counter is the summation of the values of the fethPortReadableOctets counters for all of the ports in the group. This statistic provides an ...

fethGroupLower32TotalOctets

The total number of octets contained in the valid frames that have been received on the ports in this group. This counter is the summation of the values of the fethPortReadableOctets counters for all of the ports in the group. This statistic provides an ...

fethGroupTotalErrors

The total number of errors which have occurred on all of the ports in this group. This counter is the summation of the values of the fethPortTotalErrors counters for all of the ports in the group. REFERENCE Reference IETF 100Base-T Repeater MIB, rptr100Mo ...

fethGroupFefiEnable

This item enables\disables the FEFI mechanism of the PHY on the module. It enables\disables both the transmission and the recognition of FEFI signals . This item is used only in modules that support 100BaseFx.

tokRingTable

tokRingEntry

tokRingAgId

ID of the agent to which the ring belongs in the tokRingTable.

tokRingId

ID of the ring in the tokRingTable.

tokRingLeftSlot

Slot number of the left-most slot of the ring. In the token ring stackable hub, 'Left' should be read as 'Up'.

tokRingRightSlot

Slot number of the right-most slot of the ring that has a lobe port. In the token ring stackable hub, 'Right' should be read as 'Down'.

tokRingTrafficBuffer

Record of traffic for the last second with a resolution of 100 msec. The traffic is expressed in percents of the maximum effective TR traffic (token messages are excluded) and each record contains 10 readings, in range 1..20 on log(10) scale.

tokRingTrafficThresh

Traffic threshold value. When exceeded, a trap is send to the management console. Expressed in percents of the maximum effective TR traffic (token messages are excluded) in the range 1..20 on log(10) scale.

tokRingPeakTraffic

Maximal traffic value since last reset of agent. Expressed in percents of the maximum effective TR traffic (token messages are excluded), in the range 1..20 on log(10) scale. The write access is reserved for resetting the value of the peak.

tokRingNumberOfStations

Number of Token Ring stations (controllers) detected on the ring. The TR controller of the agent card is included in this count.

tokRingConfiguration

Configuration attribute describing the list of physical addresses detected on the Token Ring. Coded in internal application format.

tokRingBeaconing

This attribute indicates if a beaconing condition is currently detected on the ring.

tokRingBeaconingStation

The MAC address of the last station which was detected as sending Beaconing MAC frames on the ring.

tokRingStationsMatch

This attribute indicates matching between the number of stations detected on the ring between the current agent and the next agent on Up Stream sense and the number of connected lobe ports.Used by the port address correlation mechanism.

tokRingTraffic

Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Ethernet traffic in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ).

tokRingSecurityMethod

Security scheme selected by the user. perPort(1) indicates that secure addresses are defined for each secured token ring port. perRing(2) indicates that a common set of secure addresses will be allowed for the whole ring. disabled(3) - no security method ...

tokRingSecurityPolicy

Security policy (trap only or trap and disconnect) selected for the ring. Coded in internal format.

tokRingSecureAddr

Secure addresses assigned to the ring. Coded in internal format.

tokRingLastViolation

MAC address of a last detected intruder.

tokRingUtilization

Last traffic reading (sampling time = 100 msec). The traffic is expressed in percents of the maximum Token Ring traffic.

tokRingPeakUtilization

Maximal traffic value since last reset of agent. Expressed in percents of the maximum effective TR traffic (token messages are excluded).

tokRingBeaconingResolution

This parameter enables or disables the beaconing resolution.

tokRingThresholdStatus

This item is a bitmap that defines the threshold status of the ring, in relation to the alarmPolicyTable. If the ring is monitored by the agent according to policy number x in the alarmPolicyTable, and the threshold condition has occured, then the bit #x ...

tokRingActiveMonitor

The MAC Address of the station functioning as Active Monitor.

tokGroupTable

tokGroupEntry

tokGroupId

Number of the slot in which the group is installed.

tokGroupAutoRightLoop

Value ON of this attribute signifies that a hardware loop was automatically created on a Token Ring module which does not sense the existence of another token ring group on the right hand side. In the token ring stackable hub, 'Right' should be read as 'D ...

tokGroupAutoLeftLoop

Value ON of this attribute signifies that a hardware loop was automatically created on a Token Ring module which does not sense the existence of another token ring group on the left hand side. In the token ring stackable hub, 'Left' should be read as 'Up' ...

tokGroupManRightLoop

Setting this attribute to ON signifies a command to the hardware to create a loop on the Token Ring module which isolates the ring from the right hand side. In the token ring stackable hub, 'Right' should be read as 'Down'.

tokGroupManLeftLoop

Setting this attribute to ON signifies a command to the hardware to create a loop on the Token Ring module which isolates the ring from the left hand side. In the token ring stackable hub, 'Left' should be read as 'Up'.

tokGroupRightNeighbor

Attribute defining the existence of a neighbor another token ring group on the right hand side of the module. In the token ring stackable hub, 'Right' should be read as 'Down'.

tokGroupLeftNeighbor

Attribute defining the existence of a neighbor another token ring group on the left hand side of the module. In the token ring stackable hub, 'Left' should be read as 'Up'.

tokGroupIOMode

Attribute defining the I/O mode (single, dual-ring-in, dual-ring-out) Lobe, Internal Repeater or Star) of a module from the the LTR-IO family.

tokGroupBridgeMode

Attribute describing the operational mode of the bridge. For ITLB the following modes are defined: - Mode A: First channel connected to an external ring (RI,RO connectors) and second channel connected to an internal ring; - Mode B: First channel connected ...

tokGroupManLinkLoop

Setting the value of this attribute to ON instructs the hardware of a Token Ring repeater module to close the loop in the direction of the external connection.

tokGroupManBusLoop

Setting the value of this attribute to ON instructs the hardware of a Token Ring repeater module to close the loop in the direction of the internal bus.

tokGroupAutoLinkLoop

Value ON of this attribute signifies that a hardware loop has been auto- matically closed by the hardwar of the Token Ring repeater as a result of problems on the external link.

tokGroupAutoBusLoop

Value ON of this attribute signifies that a hardware loop has been auto- matically closed by the hardware of the Token Ring repeater as a result of problems on the internal bus.

tokGroupSpecificOID

This attribute provides the OID of another group containing additional more specific information regarding this instance.

tokGroupStarSpeedDetect

This attribute enables the speed detection mechanism for the ports which are in star mode

tokGroupLobeSpeedDetect

This attribute enables the speed detection mechanism for all ports which are in Lobe mode, at module level.

tokGroupLSTBeaconing

This item is for LST168 only. The ring is in beaconning state. Value 'on' informs on beacon fault when the number of consecutive beacon frames is above BeaconThreshold.

tokGroupLSTBeaconThresh

This item is for LST168 only.Threshold for the number of consecutive beacon frames in the ring, above which a beaconning fault is alerted.

tokGroupRingTable

tokGroupRingEntry

tokGroupRingGroupId

ID of the group to which the ring belongs.

tokGroupRingId

ID of the ring.

tokGroupRingSpeed

Attribute describing the bandwidth of the ring.

tokGroupRingInserted

Indicates that the bridge interface has inserted itself into the ring.

tokGroupRingStatus

This item sets the connection of a TR controller to one of its possible connections, identified by the index of this row, for modules with a multiple interface controller (for example ITRP).

tokPortTable

tokPortEntry

tokPortGroupId

ID of the group to which the token ring port belongs.

tokPortId

ID of the port in the tokPortTable.

tokPortBypass

Setting the value of this attribute to ON causes the by- passing of the TokenRing port.

tokPortConnected

Attribute which describes the connection status of a Token Ring port (inclusion of the Token Ring controller in the ring).

tokPortTCP

Setting the value of this attribute to ON causes the activation of the cable-fault detection mechanism.

tokPortCableFault

Value ON of this attribute signifies the detection of a cable-fault on this specific Token Ring port.

tokPortFunctionalStatus

The value of this attribute reflects the functional status of Token Ring ports. Note that it is not mandatory that a certain port support all the enumerated states. Here is the lest of the possible states: ok(1) - fully functional port, transmitting and r ...

tokPortLastSourceAddr

MAC source address of the last readable frame received by this port.

tokPortSpecificOID

This attribute provides the OID of another group containing additional more specific information regarding this instance.

tokPortRingSpeedError

This attribute is set to 'on' when the station tries to enter the ring with a speed different from the speed of the ring.

tokPortSpeedDetect

This attribute enables the speed detection mechanism on a port level.

tokPortRingId

Unique identifier of the ring/ring segment to which a specific port is connected.

tokPortMapping

This attribute enables/disables participation of the selected port in port-to-address correlation algorithm. Default value is on(1).

tokRingStationTable

tokRingStationEntry

tokRingStationRingId

ID of the ring in the in which the station is inserted.

tokRingStationMAC

This item defines the MAC address (in token ring format) of the station connected to the ring.

tokRingStationLineErrors

This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or tok ...

tokRingStationInternalErrors

This counter is incremented when a station recognizes an internal error. Internal errors are detected by the adapter's hardware and/or firmware. They usually cause the detecting adapter to remove itself from the ring.

tokRingStationBurstErrors

This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error).

tokRingStationACErrors

This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is equal to C is equal to 0 without first receiving an AMP frame. It denotes a station that cannot s ...

tokRingStationAbortsTrans

This counter is incremented when a station transmits an abort delimiter while transmitting.

tokRingStationLostFrames

This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where a transmitting station in strip mode does not receive the trailer of the frame before the TRR timer goes off.

tokRingStationReceiveCongErrors

This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer space indicating that the station is congested.

tokRingStationFramesCopied

This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A bits are set to 1 indicating a possible line hit or duplicate address.

tokRingStationFrequencyErrors

The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency by more than that specified by the IEEE 802.5 standard.

tokRingStationTokenErrors

This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmitted.

tokRingStationTotalErrors

This counter is the sum of all REM counters for this station, i.e.: LineErrors, InternalErrors, BurstErrors, ACErrors, AbortsTrans, LostFrames, FrameCopiedErrors, ReceiveCongestionsErrors, FrequencyErrors, TokenErrors.

tokRingStationFunctionalType

The function of the concerned station in the ring.

tokIntPortTable

Table of configuration attributes for items specific to token ring internal ports, which can not be addressed via the genIntPort group.

tokIntPortEntry

An entry in the table, containing data about a single port.

tokIntPortGroupId

Index which identifies the group inside the hub for which this entry contains information. Equals the number of the slot by which the group containing the internal port is accessed. This value is never greater than chNumberOfSlots.

tokIntPortId

Index which identifies the internal port inside the group for which this entry contains information. This value is never greater than genGroupNumberOfIntPorts of the group to which the port belongs.

tokIntPortLeftNeighbor

Attribute defining the existence of another token ring group to the left hand side of the module, on the TR bus to which this intrnal port is connected. The value bypass is reported when the controller is not connected to the bus.

tokIntPortRightNeighbor

Attribute defining the existence of another token ring group to the left hand side of the module, on the TR bus to which this intrnal port is connected. The value bypass is reported when the controller is not connected to the bus.

tokIntPortManLeftLoop

Setting this attribute to on signifies a command to the hardware to create a loop to the left of the module, on the bus to which this internal port is connected.

tokIntPortManRightLoop

Setting this attribute to on signifies a command to the hardware to create a loop to the left of the module, on the bus to which this internal port is connected.

tokIntPortAutoLeftLoop

Value 'on' of this attribute signifies that a left hardware loop was created on the Token Ring bus to which this internal port is connected.

tokIntPortAutoRightLoop

Value 'on' of this attribute signifies that a right hardware loop was created on the Token Ring bus to which this internal port is connected.

tsGroupTable

tsGroupEntry

tsGroupId

Number of the slot in which the group is installed.

tsGroupLATStatus

Value ON of this attribute means that LAT protocol is Enabled on the Ethernet module.

tsGroupOperationMode

This attribute describes the operation mode of the module in a multiprocessor configuration sensor, as reported by interprocessors communication.

ltalkPortTable

ltalkPortEntry

ltalkPortGroupId

Number of the group to which the port belongs.

ltalkPortId

ID of the port in the ltalkPortTable.

ltalkPortTest

A value ON of this attribute indicates that a port test should be performed upon the port defined by the attribute instance.

ltalkPortTestResult

Indicates the result of a port test performed on this port.

ltalkPortJam

An ON value of this attribute indicates a Jam error on the specific port.

clGroupTable

clGroupEntry

clGroupId

Number of the slot in which the group is installed.

clGroupClockRedundancy

Value ON of this attribute defines a redundancy (backup) relationship between the internal and external clocks on the LCL100 module.

clGroupMainClock

Value of this attribute is an index into clPortTable, and defines the clock that should operate or a main clock in redundancy scheme. Serves as 'Clock selection' switch on the card.

clGroupTestClocks

A value ON of this attribute indicates that a test should be performed on all clock ports.

clPortTable

clPortEntry

clPortGroupId

Number of the group to which the port belongs.

clPortId

ID of the port in the clPortTable.

clPortFunctionalStatus

Indicates whether the clock is faulty or not.

iwrGroupTable

Attributes pertaining to the integrated router module.

iwrGroupEntry

An entry in the table.

iwrGroupId

Slot number in which the module is located.

iwrOperState

One of the possible states of the module. run(1) - indicates a successful completion of the boot and self test procedure. boot(2) - indicates that the module is performing the boot and self-test procedure. fail(3) - indicates an unsuccessful completion of ...

iwrPMState

The state of the Processor Module.

iwrIOMState

The state of the Input/Output Module.

iwrEthernetMode

Determines whether the ex10bt(2) LAN controller is connected to the front panel 10BaseT or to backplane bus4(1).

iwrPrimaryFDDIInsert

This variable is specific to the IEFR router and reflect the status of the Primary - P FDDI interfaces of the router. There is a corresponding LED for each one on the front pannel and this information may be used to build a 'real-life' representation of t ...

iwrSecondaryFDDIInsert

This variable is specific to the IEFR router and reflect the status of the Secondary - S FDDI interfaces of the router. There is a corresponding LED for each one on the front pannel and this information may be used to build a 'real-life' representation of ...

iwrWANTable

WAN data table.

iwrWANEntry

Entry in the table.

iwrWANGroupId

Slot number in which the module is located.

iwrWANPortId

WAN port index.

iwrWANConnection

WAN connection status.

iwrWANPortCableType

Cable type connected to the specified WAN port.

iwrInterfaceAddrTable

The table contain for each interface: 1. The IP address that was configured to the interface. 2. The IP netmask that was configured to the interface. All the network bits are set to 1 and all the hosts bits are set to 0. 3. The Mac Address assigned to the ...

iwrInterfaceEntry

Entry in the table.

iwrInterfaceGroupId

Slot number in which the module is located.

iwrInterfaceId

IP Interface port index.

iwrInterfaceAddr

The IP Address of this indexed port.

iwrInterfaceMask

The IP Address Mask of this indexed port.

iwrInterfaceMacAddress

The Mac Address of this indexed interface.

itrGroupTable

Table of attributes pertaining to the ITRE module.

itrGroupEntry

An entry in the table.

itrGroupId

Slot number in which the module is located.

itrMainSWVersion

Software version of the main CPU.

itrConfigState

Configuration state of the module.

itrModuleState

State of the ISTC/IFTC modules.

itrLinkTable

ITRE links table.

itrLinkEntry

Entry in the table.

itrLinkGroupId

Slot number in which the module is located.

itrLinkPortId

Link identifier.

itrLinkIf

Interface type.

itrLinkMode

Synchronous or asynchronous modes on the link.

itrLinkAsyncRate

Possible link speeds that can be set in asynchronous mode.

itrLinkSyncRate

Link speeds in synchronous mode.

itrLinkParity

This attribute enables/disables parity checking.

itrLinkParityEvenOdd

Even or odd parity.

itrLinkStopBit

Number of stop bits (1 or 2 ) in asynchronous mode. The value 'none' is returned in synchronous mode.

itrLinkRemoteLANConn

This attribute shows whether the remote ITRE is connected to the LAN.

itrLinkFunctionalStatus

The attribute represents the status of the WAN link.

itrLinkAdminStatus

The administrative status of the WAN port of the ITRE/IERE family. enabled(1) enables the WAN link, disabled(3) disables it, and enableddOnDemand(2) allows the ITRE/IERE to decide whether to open the port or close it. In this case, it's RO value and the s ...

itrLinkReset

Reset the WAN link

itrLinkConnectionStatus

This attribute represents the end-to-end connection status of the WAN link. When the connection is ok, the link is 'on(1)'. When the connection is lost the link is 'trying(3)'constantly to re-establish the connection until it becomes 'on(1)' or 'off(2)' .

itrLinkDataBits

Number of data bits (7 or 8) in asynchronous mode. The value 'notSupported' is returned in synchronous mode.

itrLinkControlSignalsMode

The value of this attribute determines the control signals (RTS,CTS, CD) mode while working with a MODEM, either in synchronous or asynchronous mode. When the Control Signals Mode is disabled, there is no flow control with the MODEM.

itrLinkParityType

This attribute represents the parity type in asynchronous mode. The value 'none' is returned in synchronous mode.

lntFddiPortTable

lntFddiPortEntry

lntFddiPortGroupId

Id of the slot to which the fddi port belongs.

lntFddiPortId

Id of the port.

lntFddiPortMACCurrentPath

Indicates the association of the MAC with the link path.

lntFddiPortOpticalSwitchExist

This attribute describes the presence of the optical switch and for existing optical switches describes the possibility of the auto-reconfiguration of path resources in the case of power fault.

lntFddiPortRingConfiguration

Attribute which summarizes the status of the fddi link. It is related to the light detection in the physical fiber.

lntFddiPortLineStatusA

Attribute that reflects the status of fddi line, interface a.

lntFddiPortLineStatusB

Attribute that reflects the status of fddi line, interface b.

lntFddiPortRxTotalPackets

Number of total packets, including errors, received

lntFddiPortRxTotalOctets

Number of total octets, including errors, received

lntFddiPortTxTotalPackets

Number of total packets, including errors, transmitted

lntFddiPortTxTotalOctets

Number of total octets, including errors, transmitted

lntFddiPortIPXtoFDDIMatching

Conversion matching from IPX to FDDI in Novell environment

lntFddiPortFDDItoIPXMatching

Conversion matching from FDDI to IPX in Novell environment