NETSCREEN-NAT-MIB Download

nsNatMipTable

Mapped IP(MIP) is a direct one-to-one maping of traffic destined for one IP address ot another IP address. On NetScreen device, MIP addresses for tunnel and untrusted interfaces can be created.

nsNatMipEntry

An entry containing attributes of a mip address

nsNatMipIndex

A unique value for each address. Its value ranges between 0 and 65535 and may not be contingous.

nsNatMipIp

mip address. A MIP must be in the same subnet as the tunnel interface to which it is linked to; however, for the untrusted interface, a MIP does not need to be in the same subnet. In either case, a MIP must not be the same as the interface address or be i ...

nsNatMipNetmask

Subnet mask for this MIP.

nsNatMipHost

Host ip address mip mapping to.

nsNatMipIfIp

Interface's ip address that a MIP is linked to.

nsNatMipIfNetmask

Interface's netmask that a MIP is linked to.

nsNatMipVsys

Virtual system this mip belongs to.

nsNatDipTable

A DIP(Dynamic IP) pool is a range of IP addresses from which the NetScreen device can dynamically take addresses to use when performing NAT on the source IP address of outgoing or incoming IP packets.

nsNatDipEntry

An entry containing attributes of a dynamic address

nsNatDipIndex

A unique value for each address. Its value ranges between 0 and 65535 and may not be contigous.

nsNatDipId

DIP pool id.

nsNatDipLow

Start IP Address Range. The range of addresses in a DIP pool must be in the same subnet as the interface IP address, but the DIP pool should not contain the interface IP or any MIP or VIP address that might on that subnet.

nsNatDipHigh

End IP Address Range. The range of addresses in a DIP pool must be in the same subnet as the interface IP address, but the DIP pool should not contain the interface IP or any MIP or VIP address that might on that subnet.

nsNatDipIfIp

Interface's ip address that a DIP is linked to.

nsNatDipIfNetmask

interface's ip address that a DIP is linked to.

nsNatDipPTEnable

Enable Port Translation

nsNatDipVsys

virtual system this dip belongs to

nsNatVipCfgTable

VIP(Virtual IP) allows you to map routable IP addresses to internal servers, therby providing transparent connections for a NAT networks to the Internet. This table collects all VIP configurations in NetScreen device.

nsNatVipCfgEntry

Each entry in the nsNatVipCfgTable holds a set of configuration parameters associated with an instance of VIP.

nsNatVipCfgIndex

A unique value for each vip configuation. Its value ranges between 1 and 65535 and may not be contingous.

nsNatVipCfgIp

The IP address for the VIP, which must be in the same subnet as the untrusted interface and can even be the same address as the untrusted interface.

nsNatVipCfgPort

The port number for communication between the trusted server and the untrusted interfce on the NetScreen device.

nsNatVipCfgService

Service for the server on the trusted interface.

nsNatVipCfgStatus

The status of the server on the trusted/DMZ interface.

nsNatVipCfgLoadBalance

Load balance algorithm for the Virtual IP servers.

nsNatVipServerTable

Ballancing the loads on NetScreen servers allow traffic intended for a server(one IP address on the untrusted network) to be mapped to several different IP addresses on the DMZ or trusted network. There can be up to eight servers in one load balancing gro ...

nsNatVipServerEntry

An entry containing attributes of a vip configuration's server pool.

nsNatVipServerIndex

A unique value for each vip server configuation. Its value ranges between 1 and 65535 and may not be contigous.

nsNatVipServerVIP

The IP address for the VIP.

nsNatVipServerService

Service provideing through the VIP.

nsNatVipServerLoadBalance

Load balance algorithm for the vitural IP servers.

nsNatVipServerIp

Virtual IP server's IP address.

nsNatVipServerWeight

Loadbalance algorithm weight.

nsNatVipServerStatus

Virtual IP server's status.