ODS-TRMIB Download

boxChassisId

The type of chassis used for the concentrator. For modular concentrators, the hardware is further qualifed by the value of cardId for each card installed in the concentrator.

boxMaxDeinCount

Contains the maximum number of successive de-inserts that can occur before a given port is shut off automatically.

boxMaxDeinDelta

The maximum time in seconds between successive de-inserts for a given port for which the portDeinCount will be incremeneted.

boxReset

Setting to 1 will reboot the agent.

boxFWVersion

The version of the firmware that is currently resident.

trapId

The trap Id for this particular trap. It is a one-up counter that identifies this trap.

changedOid

The Object Id of the variable that is the reason for sending the trap.

changedValue

The value of the variable that is being trapped.

changedDescr

A textual description of the variable, the slot, the port, and the new value that is being trapped.

tftpAddress

The IP address from which TFTP packets will be accepted by the agent.

dosCommand

A Dos command that will be executed.

dosExitCode

The status of the last executed DOS command.

enbBcnIsoAlg

Enable for the Beacon Isolation Algorithm. When this variable is set to enable, then if the ring beacons and is unable to recover itself, the MAU will execute the Beacon Isolation Algorithm. This algorithm will attempt to isolate the problem in the ring ...

cardNumSlots

The number of slots in the concentrator. For modular concentrators, this value is the maximum number of cards that can be installed. For non-modular concentrators, the value is always one.

cardNumCards

The number of cards actually installed in the concentrator. For non-modular concentrators, the value is always one.

cardTable

A list of card entries for each card installed in the concentrator. The number of entries is given by the value of CardNumCards.

cardEntry

A card entry containing objects pertaining to a card installed in the concentrator.

cardBypass

The current bypass state of the card.

cardRingStar

The Ring/Star mode of the card.

cardRingSpeed

The Ring Speed of the card.

cardCableType

The card's Cable Type.

cardReset

The card's Reset Switch state.

cardSwitch

The state of the HW/SW switch on the card.

cardControl

Who currently controls the card, HW or SW.

cardId

The type of card installed in the concentrator. If the chassis is a modular chassis, then cardId defines the type of card. However, if the chassis is an 841 or 861 type chassis, then boxChassisId fully defines the type of card installed, so for a non-mod ...

cardIndex

The slot in which the card is installed. This value uniquely identifies the card. Its value ranges between 1 and the value of CardNumSlots.

cardDescrip

A textual description of the card including the ODS model number, media type and number of ports.

cardNumPorts

The number of configurable ports on the card. For some cards, the value may be zero.

cardHasPorts

This value describes if there are configurable user ports on the card.

cardHasRingInt

This value describes if the card has ring in and ring out ports.

cardHasTW

This value describes if the card's user ports are twisted wire or not.

cardHasCtrl

This value describes if the card has a HW/SW Control switch or not.

cardHasBypass

This value describes if the card has a Bypass switch or not.

portTable

A list of port entries for each interface port in the concentrator. The number of entries is given by the sum of CardNumPorts for each card in the CardTable.

portEntry

A port entry containing objects pertaining to an interface port in the concentrator.

portEnable

The current enable status of the port. If the value is off(2), no data is passed through the port.

portActStatus

Whether we currently see activity on the port. If we have activity, then the value is true(1).

portRingInsert

Whether someone is currently inserted onto the ring through this port. If true(1), then someone is inserted onto this port.

portDeinCount

Current count of successive deinserts that occurred on this port, each within MaxDeinDelta of the previous deinsert.

portCard

The card on which the port exists. The card identified by this value is the same card as identified by the same value of CardIndex.

portIndex

An integer which uniquely identifes this port on the card. Its value ranges between 1 and the value of CardNumPorts for the card.

ringportTable

A list of entries for Ring In and Ring Out ports of the concentrator.

ringEntry

A ring port entry containing objects pertaining the concentrator's Ring In and Ring Out ports.

rpMode

The current status of the ring port.

rpFOTW

Whether fiber optic or twisted wire are currently being used by the ring port.

rpLoopBack

Whether the concentrator's ring port is in loopback mode.

rpVoltSense

Whether voltage is being sensed across the ring port.

rpActStatus

Whether we currently see activity on the port. if we have activity, then the value is true(1).

rpCarrSense

Whether a carrier is sensed on the ring port.

rpCard

The card on which the ring ports exist. The card identified by this value is the same card as identified by the same value of CardIndex.

rpIndex

An integer which uniquely identifies this ring port on the card. Its value ranges between 1 (Ring In) and 2 (Ring Out).

rpHasTW

Whether or not the ring port has Twisted Wire.

teLoopBack

The Loopback state for a ring port has changed. This trap will be sent to the defined management station(s) if the value of teLoopBack enabled(1).

teMode

The state of the Ring Port mode switch has changed (Normal, Internal Loop, Auto Loop). This trap will be sent to the defined management station(s) if the value of teMode is enabled(1).

teFOTW

The state of the Fiber Optic/Twisted Wire switch has changed. This trap will be sent to the defined management station(s) if the value of teFOTW is enabled(1).

teRingInsert

A user was inserted onto the ring or de-inserted from the ring. This trap will be sent to the defined management station(s) if the value of teRingInsert is enabled(1).

teDeinCount

The De-insert count for one of the user ports is now greater than 1. This trap will be sent to the defined management station(s) if the value of teDeinCount is enabled(1).

teEnable

The state of one of the user port switches has changed. This trap will be sent to the defined management station(s) if the value of teEnable is enabled(1).

teBypass

The state of the Bypass control switch has changed. This trap will be sent to the defined management station(s) if the value of teBypass is enabled(1).

teRingStar

The state of the Ring/Star control switch has changed. This trap will be sent to the defined management station(s) if the value of teRingStar is enabled(1).

teRingSpeed

The state of the Ring Speed (Clock) control switch has changed. This trap will be sent to the defined management station(s) if the value of te_4_16 is enabled(1).

teCableType

The state of the Cable Type control switch has changed. This trap will be sent to the defined management station(s) if the value of teCableType is enabled(1).

teSwitch

The state of the HW/SW control switch has changed. This trap will be sent to the defined management station(s) if the value of teSwitch is enabled(1).

teLanManager

The Ringin or Ringout has gone into Loopback. This alert will be sent to IBM's Lan Manager management station(s) if the value of teLanManager is enabled(1).