XSWITCH-MIB Download

scGenChMainAgPosition

This attribute defines the position in the chassis where the Main Agent resides.

scGenChRedunAgPosition

This attribute defines the position in the chassis where the Redundant Agent resides. 0 means Redundant Agent not present.

scGenChRedunAgActivityStatus

This attribute defines the status of the Redundant Agent. notPresent(1) - indicates that no redundant Agent exists. dormant(2) - indicates that the redundant Agent is ok and may at any moment become the Agent of the system. active(3) - indicates that the ...

scGenChAgVLAN

The Virtual LAN number of the Agent's internal interface. The value 0 means Generic ( But can communicate with Global !). The values '255' mean Global.

scGenMonTable

Table of attributes which define Monitoring information about a single XSwitch in SC based devices.

scGenMonEntry

An entry in the table, containing data about a single XSwitch.

scGenMonSwitchId

Index which identifies the XSwitch for which this entry contains information. This value is never greater than chNumberOfXSwitches.

scGenMonDropEvents

The total number of events in which the probe could not count packets due to lack of resources. This number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.

scGenMonOctets

The total number of good octets switched and error octets filtered by this XSwitch.

scGenMonPkts

The total number of good packets switched and error packets filtered by this XSwitch.

scGenMonGoodBroadcastPkts

The total number of good packets switched by this XSwitch that were directed to the broadcast address.

scGenMonGoodMulticastPkts

The total number of good packets switched by this XSwitch that were directed to the multicast address. Note that this number does not include packets directed to the broadcast address.

scGenMonGoodPkts

The total number of good packets switched by this XSwitch.

scGenMonBadPkts

The total number of bad packets filtered by this XSwitch.

scGenMonGoodOctets

The total number of good octets switched by this XSwitch.

scGenMonBadOctets

The total number of bad octets filtered by this XSwitch.

scGenMonSmonCapability

This item is used to define which smon's application are implemented in the agent. When the console first performs smon application it should read this item in order to know which of the smon's applications are available in this agent's version. When ther ...

scGenMonSwitchVLANList

A bitmap defining the status of the virtual LANs in the Virtual LAN Table. The first bit is for Virtual LAN 0, the second for Virtual LAN 1, and so on. If the Virtual LAN exists in the hub the value of the associated bit is 1, otherwise 0.

scGenMonMIBCtrList

A bitmap defining the status of the MIBCtrMode for every group in the switch. The MSB (Most significant bit) representing the status of group #1. If MIBCtrMode on a group is enable(1) the bit is set to 1, otherwise 0.

scGenMonTimeStamp

This attribute contains the value of sysUpTime at the time switch counters were calculated.

scGenMonVlanTimeStamp

This attribute contains the value of sysUpTime at the time VLAN counters were calculated.

scGenMonPriorityTable

A list of priority count entries.

scGenMonPriorityEntry

A list of statistics related to a specific priority level on a single XSwitch in SC based devices.

scGenMonPrioritySwitchId

Index which identifies the XSwitch for which this entry contains information. This value is never greater than chNumberOfXSwitches.

scGenMonPriorityId

The priority for which this entry reports statistics. 1=regular. 2=high.

scGenMonPriorityGoodPkts

The total number of good packets switched by this XSwitch using this packet priority level.

scGenMonPriorityGoodOctets

The total number of good octets switched by this XSwitch using this packet priority level.

scGenMonVLANList

A bitmap defining the status of the virtual LANs in the Virtual LAN Table. The first bit is for Virtual LAN 0, the second for Virtual LAN 1, and so on. If the Virtual LAN exists in the hub the value of the associated bit is 1, otherwise 0.

scGenMonVLANTable

A list of virtual LAN statistics.

scGenMonVLANEntry

A list of statistics related to a specific Virtual LAN.

scGenMonVLANSwitchId

Index which identifies the XSwitch for which this entry contains information. This value is never greater than chNumberOfXSwitches.

scGenMonVLANId

The Virtual LAN for which this entry contains information.

scGenMonVLANGoodPkts

The total number of good packets switched by the XSwitch on this Virtual LAN.

scGenMonVLANGoodOctets

The total number of good octets switched by the XSwitch on this Virtual LAN.

scGenMonVLANStatsUcastPkts

The total number of good unicast packets switched by the XSwitch on this Virtual LAN.

scGenMonVLANStatsMcastPkts

The total number of good multicast packets switched by the XSwitch on this Virtual LAN.

scGenMonVLANStatsBcastPkts

The total number of good broadcast packets switched by the XSwitch on this Virtual LAN.

scGenMonSwitches

A bitmap defining the switch status, whether it is functional or not. The list should start with the MSB. Value of each bit: 0 - the switch is not functional 1 - the switch is functional The mapping is: Bit 0 : Left DomainX Bit 1 : Right DomainX

scHostTimePortCorrTable

An addition to the RMON MIB's hostTimeTable. This table contains a list of MAC addresses that were monitored on the switch and the ports to which they are connected. The index of this table is the same as for the standard RMON hostTimeTable. Indexes are s ...

scHostTimePortCorrEntry

An entry in the MAC to port correlation table.

scHostTimeAddress

The physical address of this host.

scHostTimeCreationOrder

An index that uniquely identifies an entry in the hostTime table among those entries associated with the same hostControlEntry. This index shall be between 1 and N, where N is the value of the associated hostControlTableSize. The ordering of the indexes ...

scHostTimeIndex

The set of collected RMON host statistics of which this entry is a part. The set of hosts identified by a particular value of this index is associated with the hostControlEntry as identified by the same value of hostControlIndex.

scHostTimePortConnection

The switch port to which this scHostTimeAddress is connected. The coding of the port number for Visage switches is: 32*(H-1)+P, where H is the number of the hub in the stack and P the port in the hub (1.. 32). For hosts whose port connection is not identi ...

scGenGroupTable

Table of attributes which define general configuration information about a single SC based group.

scGenGroupEntry

An entry in the table, containing data about a single Group.

scGenGroupId

Unique Id of the group in the scGenGroupTable. Equals the number of the slot by which the group is accessed.

scGenGroupUseSwitches

This attribute reflects the status of the `Use Switches' switch which defines the working mode of the module. on - The module works according to the switches. No Set commands may be performed on attributes related to the switches. off - Ignore Dip Switche ...

scGenGroupCopyPortSupport

Indication whether a module supports Copy-Port [on(1)], or does not support Copy-Port [off(2)].

scGenGroupXswitchConnection

This attribute identifies the Xswitch number (1..4) to which the module is connected to. In non-bridged configuration, there are potentialy up to 4 Xswitches - 1&2 for left&right Ethernet Xswitches and 3&4 for left&right TR Xswitches. In bridged configura ...

scGenGroupStatus

This attributes defines the status of the Xswitch module. The value 'loadsBudgetProblem' indicates that the module cannot be connected to the Xswitch because it exceeds the maximum number of loads allowed in the Xswitch.

scGenGroupSwitchType

This attribute defines the Xswitch type of the module.

scGenGroupNumberOfLoads

This attribute identifies the number of loads which that Xswitch module represents.

scGenGroupSetDefaults

Set all module and ports parameters in the XSwitch module, to their default values. This item will always return a value of off(2), since it acts like a toggle switch. Set of layer2Only(3) value, will cause partial setting, to layer2 parameters only

scGenGroupSupportCopyPortList

A bitmap defining the status of each port of the hub\module whether it support copy port or not, 0 - the port does not support copy port 1 - the port support the copy port the list should start with the MSB indicates port number 1 (one) and the LSB ...

scGenGroupSupportPortCountersList

A bitmap defining the status of each port of the hub\module whether it supports the port's counters, 0 - the port does not support port's counters 1 - the port support the port's counters the list should start with the MSB indicates port number 1 (o ...

scGenGroupSupportSegCountersList

A bitmap defining the status of each port of the hub\module whether it supports the segment counters on port, 0 - the port does not support segment's counters 1 - the port support the segment's counters the list should start with the MSB indicates por ...

scGenGroupUpLinkType

The type of the Up Link port Relevant only for the 25th port of Visage 2500: Fiber (1) - 100BaseFX, Copper (2) -100BaseTX.

scGenGroupPlugInType

Attribute describing the type of the plug-in module

scGenGroupPlugInDescr

Descriptor of the plug-in in ASCII (readable) format, mainly for use with Generic management applications.

scGenGroupPlugInCS

ASCII string for description and display of the plug-in module configuration symbol. The format of the number is XXXX.YY

scGenGroupDefaultVLAN

Attribute describing the Default VLAN configuration on the switch ports of the module. It is determined according to scGenSwitchDefaultVLAN parameter of the agent.

scGenGroupCascadingType

Attribute describing the type of the cascding module

scGenGroupCascadingDescr

Descriptor of the cascading module in ASCII (readable) format, mainly for use with Generic management applications.

scGenGroupCascadingCS

ASCII string for description and display of the cascading module configuration symbol. The format of the number is XXX.YYY

scGenGroupSupportDstCopyPortList

A bitmap defining the status of each port of the hub\module whether it supports the capability of being a destination copy-port . 1 - the port has the capability of being a destination copy-port 0 - the port does not have the capability of being a d ...

scGenGroupBUPSType

Attribute describing the type of the BUPS module

scGenGroupBUPSCS

ASCII string for description and display of the BUPS module configuration symbol. The format of the number is X.Y

scGenGroupBUPSFansStatus

The operational status of the fans included in the BUPS module: allFansOK(1) - all BUPS module's fans are operational. oneFanFailed(2) - at least one of the BUPS module's fan is failed.

scGenGroupFansStatus

The operational status of the fans included in the module: allFansOK(1) - all module's fans are operational. oneFanFailed(2) - at least one of the module's fan is failed.

scGenGroupInternalBuffering

Control the internal buffering capacity.

scGenGroupMcFilterBoxSupport

Tells whether the box hardware supports filtering or not.

scGenGroupMcFilterPersonalitySupport

Tells whether the personality hardware supports filtering or not. The value PersonalityNotInstalld means that the a personality Extention was not installed in the specific box

scGenGroupMcFilterStackingSupport

Tells whether the stacking hardware supports filtering or not The value StackingNotInstalld means that the a stacking daughter board was not installed in the specific box

scGenGroupLACPMode

The value of this attribute determines whether LACPDU messages can be exchanged by the module's ports. If enabled, the ports will exchange LACPDU messages according to their scGenPortLACPMode MIB. If disabled, every port of the module will not exchange LA ...

scGenGroupSecurityMode

Group intrusion security mode assigned to this module. securityMode - all ports in this module are secure according to their scGenPortSecurityMode MIB's value. nonSecurityMode - all ports in this module are not secure.

scGenGroupBroadcastStormControl

Set the Broadcast Storm Control function on all switch ports. On means that Broadcast, Multicast or Unknown packets are discarded on an ingress port, when the rate of those packets, received on the port, is above the scGenGroupBroadcastThreshold, as set b ...

scGenGroupBroadcastThreshold

Set the Rate Threshold, in packets per second, above which Broadcast, Multicast or Unknown packets are discarded on ingress port.

scGenGroupPriorityQueuesScheduling

Set the Priority Queues Scheduling scheme for packets transmission from egress ports. Strict - will serve higher priority queue before lower priority queue, as long as the higher queue has packets. Weighted - will serve higher priority queue before lower ...

scGenGroupBoundedDelay

Set the Bounded Delay function in the switch. On will ensure that time-sensitive packets will be forwarded through the switch in no more than a maximum delay.

scGenGroupSLDAdminStatus

set the Self Loop Discovery application to enable/disable. This works with the scGenPortSLDAdminStatus

scGenGroupSmonTable

Table of smon capabilities in a single group.

scGenGroupSmonEntry

An entry in the table, containing data about a single Group.

scGenGroupSmonGroupId

Unique Id of the group in the scGenGroupSmonTable. Equals the number of the slot by which the group is accessed.

scGenGroupSmonCapability

This item is used to define which smon's application are implemented in the group. When there is a value of 0 (zero) in the relevant bit it means that the assosiated application is not supported. When there is a value of 1 (one) in the relevant bit it me ...

scGenGroupSmonVlanList

A bitmap defining the status of the virtual LANs in the Virtual LAN Table. The first bit is for Virtual LAN 0, the second for Virtual LAN 1, and so on. If the Virtual LAN exists in the hub the value of the associated bit is 1, otherwise 0.

scGenGroupSmonDropEvents

The total number of events ,in this group, in which the probe could not count packets due to lack of resources. This number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.

scGenGroupSmonGoodBroadcastPkts

The total number of good broadcast packets in this group, switched by the Xswitch.

scGenGroupSmonGoodMulticastPkts

The total number of good multicast packets, in this group, switched by the Xswitch.

scGenGroupSmonGoodPkts

The total number of good packets, in this group, switched by the Xswitch.

scGenGroupSmonBadPkts

The total number of bad packets , in this group, filtered by the Xswitch.

scGenGroupSmonGoodOctets

The total number of good octets, in this group, switched by the Xswitch.

scGenGroupSmonBadOctets

The total number of bad octets, in this group, filtered by the Xswitch.

scGenGroupSmonPkts

The total number of packets, good and bad, in this group, switched by the Xswitch.

scGenGroupSmonOctets

The total number of octets, good and bad, in this group, switched by the Xswitch.

scGenGroupSmonMIBCtrMode

This object defines for group ports to include/exclude local segment traffic in their port counters

scGenGroupVlanTable

Table of attributes which define general VLAN counters of a single SC based group.

scGenGroupVlanEntry

An entry in the table, containing VLAN counters in a single Group.

scGenGroupVlanGroupId

Unique Id of the group in the scGenGroupVlanTable. Equals the number of the slot by which the group is accessed.

scGenGroupVlanId

The Virtual LAN for which this entry contains information.

scGenGroupVlanUcastPkts

The total number of good unicast packets ,in this group, switched by the Xswitch on this Virtual LAN.

scGenGroupVlanMcastPkts

The total number of good multicast packets ,in this group, switched by the Xswitch on this Virtual LAN.

scGenGroupVlanBcastPkts

The total number of good broadcast packets in this group, switched by the Xswitch on this Virtual LAN.

scGenGroupVlanGoodPkts

The total number of good packets ,in this group, switched by the Xswitch on this Virtual LAN.

scGenGroupVlanGoodOctets

The total number of good octets ,in this group, switched by the Xswitch on this Virtual LAN.

scGenGroupVlanUcastOctets

The total number of good unicast octets ,in this group, switched by the Xswitch on this Virtual LAN.

scGenGroupVlanMcastOctets

The total number of good multicast octets ,in this group, switched by the Xswitch on this Virtual LAN.

scGenGroupVlanBcastOctets

The total number of good broadcast octets ,in this group, switched by the Xswitch on this Virtual LAN.

scGenGroupVlanCurrentEgressPorts

The set of ports in this module which are transmitting traffic for this vlan as either tagged or untagged frames. Each module's port is represented by a single bit in this 128-bits bitmap according to the PortList convention of RFC2674. This MIB is for in ...

scGenGroupVlanCurrentUntaggedPorts

The set of ports which are transmitting traffic for this VLAN as untagged frames. Each module's port is represented by a single bit in this 128-bits bitmap according to the PortList convention of RFC2674. This MIB is for internal agent sub-agent communica ...

scGenGroupVlanStaticEgressPorts

The set of ports in this module which are permanently assigned to the egress list for this VLAN by management. Each module's port is represented by a single bit in this 128-bits bitmap according to the PortList convention of RFC2674. Changes to a bit in ...

scGenGroupVlanStaticUntaggedPorts

The set of ports which should transmit egress packets for this VLAN as untagged. Each module's port is represented by a single bit in this 128-bits bitmap according to the PortList convention of RFC2674. The default value of this object for the default VL ...

scGenGroupRspTable

.

scGenGroupRspEntry

.

scGenGroupRspGroupId

Unique Id of the group in the scGenGroupRspTable. Equals the number of the slot by which the group is accessed.

scGenGroupRspHelloInterval

The interval between transmissions of hello-messages, in 100mSec units.

scGenGroupRspDevicePollingInterval

The interval between transmissions of ARP queries for polling connectivity to the device, in 100mSec units.

scGenGroupRspDeviceNotRespondingTimeout

Amount of time in which no ARP-replies are received from the device, which cause the RSP to assume no connection to that device, in 100mSec units.

scGenGroupRspSwitchNotRespondingTimeout

Amount of time in which no hello-messages with acknowledge are received from the other switch, which cause the RSP to assume no connection to that switch, in 100mSec units.

scGenGroupRspMoveToForwardingInterval

Amount of time the port waits upon deciding to move to forwarding mode, until it moves to that mode, in 100mSec units.

scGenGroupRspBroadcastArpShortInterval

The interval in which the switch should send broadcast ARPs to the device when not knowing the MAC-address of the device, in 100mSec units.

scGenGroupRspBroadcastArpShortIntervalNumber

The number of broadcast ARPs the switch should send in short interval time, when not knowing the MAC address of the device

scGenGroupRspBroadcastArpLongInterval

The interval in which the switch should send broadcast ARPs to the device when the device does not respond to unicast ARPs, in 100mSec units.

scGenGroupRspPeriodicPingsBoxIpAddress

This MIB-item is the IP-address that the P330 box uses in order to periodically ping to devices Default value for IP Address is 0.0.0.0

scGenGroupRspPeriodicPingsDestinationIpAddress

This MIB-item sets an IpAddress that the devices will be configured to periodically ping to. The switch will be responsible to reply to ARP-queries concerning this IP-address, and which were issued by devices directly attached to it. A value of 0.0.0.0 in ...

scGenGroupRspMode

Sets the mode of the module from the RSP-application prespective. Possible modes are: RSP-module-mode-role-A - means that the ports of this module perform the RSP scheme for a device connected through a repeater, in role A (primary role). RSP-module-mode- ...

scGenPortTable

Table of attributes which define general configuration information about a single SC based port.

scGenPortEntry

An entry in the table, containing data about a single Port.

scGenPortGroupId

Id of the group to which the port belongs.

scGenPortId

Unique Id of the port in the scEthPortTable.

scGenPortVLAN

The Virtual LAN number of the Port. The value 0 means Generic ( But can communicate with Global !). The value '255' means Global.

scGenPortPriority

The priority level of the packets send by the Port.

scGenPortSetDefaults

Set all port parameters in the XSwitch module, to their default values. This item is used for ports that are managed by Sub-agents. This item will always return a value of off(2), since it acts like a toggle switch.

scGenPortBackbone

The type of the Xswitch port. 'on' indicates that the port was discovered by VIDP as backbone port.

scGenPortCopyMode

Enable /Disable the Copy Port mode in the Sub-Agent.

scGenPortCopyDestination

The destination of the copied information. The destination can be another port or the Agent acting as an RMON probe. The value of this item is: LSB Byte= sniffer channel number, Next Byte= sniffer device number. When sniffer device number=31, the destinat ...

scGenPortLinkAggregationNumber

The Link Aggregation Group (LAG) number, to which the Port belongs. The value 0 means that this port is not part of a LAG. This is also the default.

scGenPortSendBridgedPackets

When set to on(1), the port will transmit to the line bridged frames (for which their secondary VLAN was 0xFFE internally). This is the case for ports connected to a station or to another switch that has no bridging capabilities. When set to off(2), the p ...

scGenPortVLANEgressStaticConfiguration

A bitmap defining the VLANs, for which the port is member in their Egress Tables. The first bit is for VLAN 0, the second bit for VLAN 1, and so on. If the port is member in the Egress Table of a specified VLAN, then the value of the associated bit is 1, ...

scGenPortStaticVLANBinding

This object defines whether Static VLAN Binding is enabled or disabled on the port. If enabled, the port is member in the Egress List of the VLANs, as specified in scGenPortVLANEgressStaticConfiguration, in addition to its Port VLAN. If disabled, the port ...

scGenPortMaxLagsOnSec

The theoretic maximum number of LAGs that can be defined over the switching chip to which the port belongs. The value is fixed according to the switching chip type: For the Timpani chip, the value is 1. For the Guitar chip, the value is 2.

scGenPortGenericTrap

The value of this attribute determines whether or not the agent sends the snmp generic traps 2 and 3, for link down/up events on this port.

scGenPortLACPMode

The value of this attribute determines whether the port exchanges LACPDU messages, in agreement with the scGenGroupLACPMode MIB.

scGenPortLastIntruderSourceAddr

Ethernet source address of the last intrusion attempt at this port. The value of this item will be 000000 (a string of 6 zeros) if security mode is disable or no security violation at this port.

scGenPortSecurityMode

Security mode assigned to this port. nonSecurityMode - do not perform intrusion control security mechanism on this port. securityMode - perform intrusion control security mechanism and trap the console in case of security violation, if both scGenGroupSec ...

scGenPortSTA

Enable /Disable the Spanning Tree protocol for this port, meaningless when disabled at the switch level via the scGenSwitchSTA MIB.

scGenPortLagCapability

An octet string with the size of the maximum number of LAGs on the device. Each bit represents a LAG which the port may be associated with (a member of).

scGenPortCapability

Port capability bit mask, where each bit represent the capability of the port: Bit #1 - 10Mbps speed support Bit #2 - 100Mbps speed support Bit #3 - 1000Mbps speed support Bit #4 - 10000Mbps speed support Bit #9 - 2 queues support Bit #10 - 4 queues suppo ...

scGenPortSLDAdminStatus

Sets the admin status of each port in the Self Loop Discovery application A port which is disbaled does not send LDDU . A port which is enabled sends LDDU and migth turn to blocking if a SLD is discovered.

scGenPortSLDStatus

A port which is SLDEnabled can be in SelfLoop or NoSelfLoop mode . if the port is SLD disabled it will return notSupported.

scGenPortRspTable

Table of attributes which define general configuration information about a single SC based port.

scGenPortRspEntry

An entry in the table, containing data about a single Port.

scGenPortRspGroupId

Id of the group to which the port belongs.

scGenPortRspId

Unique Id of the port in the scGenPortRspTable.

scGenPortRspMode

Sets the mode of the port from the RSP-application perspective. Possible modes are: Regular - means that this is a regular port that does not participate in the RSP scheme, RSP-mode-role-A - means that this port performs the RSP scheme for a device connec ...

scGenSwitchTable

Table of attributes which define information about a single XSwitch in SC based devices.

scGenSwitchEntry

An entry in the table, containing data about a single XSwitch.

scGenSwitchId

Index which identifies the XSwitch for which this entry contains information. This value is never greater than chNumberOfXSwitches.

scGenSwitchCopyMode

Enable /Disable the Copy Port mode in the XSwitch.

scGenSwitchCopySource

The port in the switch that is being copied. All received and transmit packets on the port( including local traffic ) are copied to the defined destination, besides their normal destination. The value of this item is: 1024*S+P, where S is the slot number ...

scGenSwitchCopyDestination

The destination of the copied information. The destination can be another port or the Agent acting as an RMON probe. The value of this item is: 1024*S+P, where S is the slot number in the hub and P is the port within the slot. Value 1023 means that the de ...

scGenSwitchSetDefaults

Set all port parameters in the XSwitch, to their default values. This item will always return a value of off(2), since it acts like a toggle switch.

scGenSwitchVIDP

Enable /Disable the VIDP protocol supported in the XSwitch.

scGenSwitchType

This attribute defines the type of the Xswitch.

scGenSwitchMasterId

This attribute defines which module in the Xswitch take the role of the Master. It is equal to the slot number of the Xswitch Master.

scGenSwitchReset

Setting this attribute to `on' will cause a reset to the Xswitch. Default value is 'off'.

scGenSwitchNumberOfLoads

This attribute identifies the total number of loads of that Xswitch. There is a maximum budget of 30 loads on an single Xswitch.

scGenSwitchAgVLAN

The Virtual LAN number of the Agent's internal interface in the switch. The value 0 means Generic (But can communicate with Global !). The value '255' means Global.

scGenSwitchVLANList

A bitmap defining the status of the virtual LANs in the Virtual LAN Table. The first bit is for Virtual LAN 0, the second for Virtual LAN 1, and so on. If the Virtual LAN exists in the hub the value of the associated bit is 1, otherwise 0.

scGenSwitchSTA

Enable /Disable the Spanning Tree protocol support in the switch.

scGenSwitchSecurityMode

This item defines the Security mode per stack. nonSecurityMode - all ports in the stack are not secure. securityMode - all ports in the stack are secure according to their scGenPortSecurityMode MIB's value.

scGenSwitchFindQuery

An address to be searched for by the Agent. The Agent will start look for the address when the value is different than Null. The string format is: 1st byte: address type - 0=MAC, 1=IP Next bytes: the address. (for MAC: next 6 bytes, for IP: next 4 bytes).

scGenSwitchFindResult

The search result. The result string format is: 1st byte: address type - 0=MAC, 1=IP. Next bytes: the address. (for MAC: next 6 bytes, for IP: next 4 bytes) 7-th byte (for MAC) or 5-th byte (for IP): number of ports with the specified address. Every next ...

scGenSwitchSWRdChange

A 4-byte octet-string indicating a change performed by the SW Redundancy task. The string will include: Byte 1: Group1 (module number). Byte 2 : Port1 Byte 3 : Group2 Byte 4 : port2 Where group2 port2 are the new enabled port.

scGenSwitchDefaultVLAN

Attribute describing the Default VLAN configuration on the switch ports. The user may change the value of this parameter through the setup terminal. Vlan1 is the standard default VLAN for port configuration.

scGenSwitchVLANBridging

VLAN Bridging mode should be enabled in all Xswitches in the network, when the user wants to support network-wide VLAN Bridging. VLAN Bridging should also be enabled in one M-MLS, and PLS-Tagging mode should be set on the backbone ports.

scGenSwitchOldVersionModules

A list of modules, in ASCII format, that have older software versions than necessary in the switch. Module numbers are separated by a comma and a space. It is used to inform the user on version inconsistency.

scGenSwitchVIDPNonSupportedModules

A list of modules, in ASCII format, that do not support the VIDP function. Module numbers are separated by a comma and a space. It is used to inform the user on possible problems in VIDP function, as not all modules in the switch support VIDP.

scGenSwitchSTANonSupportedModules

A list of modules, in ASCII format, that do not support the STA function. Module numbers are separated by a comma and a space. It is used to inform the user on possible problems in STA function, as not all modules in the switch support STA.

scGenSwitchIDSNonSupportedModules

A list of modules, in ASCII format, that do not support the IDS function. Module numbers are separated by a comma and a space. It is used to inform the user on possible problems in IDS function, as not all modules in the switch support IDS.

scGenSwitchMcFilter

Enable/disable the multicast filtering mechanism supported in the switch

scGenSwitchMcFilterHostAgingTime

The Value of the Host-Aging-Time parameter used by the multicast filtering mechanism for aging learned multicast filtering information

scGenSwitchMcFilterRouterAgingTime

The Value of the Router-Aging-Time parameter used by the multicast filtering mechanism for aging learned router-ports information

scGenSwitchMcFilterDelayTime

The Value of the Delay-Time parameter used by the multicast filtering mechanism for waiting to all registration requests before applying a filter on a specific group

scGenSwitchLACPMode

The value of this attribute determines whether LACPDU messages can be exchanged by the switch's ports. If enabled, the ports will exchange LACPDU messages according to their scGenPortLACPMode MIB. If disabled, every port of the switch will not exchange LA ...

scGenSwitchSecurityModePermit

This item defines the Security mode per switch. This MIB is encoded in Lucent specific security mechanism.

scGenSwitchFastAgingOnRemoteTopChg

This item defines if the switch performs fast aging on the MAC address forwarding database (or reset the cam contents) upon reception of Topology Change BPDU from the STA root, indicating that a remote topology change has occurred. Local topology changes ...

scGenSwitchGigaMode

The value of this attribute determines the setting for the two Giga links of a P130 stack.

scGenSwitchCAMClear

When value sets to on(1), the switch clears its CAM table. This item will always return a value of off(2), since it acts like a toggle switch.

scGenLinkAggregationTable

Table of attributes which define Link Aggregation Group in a single switch.

scGenLinkAggregationEntry

An entry in the table, containing LAG information in a single switch.

scGenLinkAggregationId

The Link Aggregation number for which this entry contains information.

scGenLinkAggregationName

The Link Aggregation name, given by the user.

scGenLinkAggregationBasePortGroupId

The slot/unit number of the Base Port for this Link Aggregation.

scGenLinkAggregationBasePortId

The port number in the slot/unit of the Base Port for this Link Aggregation.

scGenLinkAggregationNumberOfPorts

The current number of ports that belong to this Link Aggregation.

scGenLinkAggregationLogicalPortGroupId

The slot number of the logical port, representing this Link Aggregation. All parameters for the LAG are managed through that logical port.

scGenLinkAggregationLogicalPortId

The logical port number in the slot, representing this Link Aggregation. All parameters for the LAG are managed through that logical port.

scGenLinkAggregationFunctionalStatus

The functional status of the LAG: ok(1) - fully functional LAG, transmitting and receiving packets on all its ports. fail(2) - all ports in the LAG are not in ok status. partialFail(3) - some of the ports in the LAG are not in ok status.

scGenLinkAggregationAutoNegResults

The auto-negotiation results for speed and duplex for the LAG ports: ok(1) - all ports resolved the same speed and duplex mode after auto-negotiation process. autoNegInconsistantResults(2) - not all ports resolved the same speed and duplex mode after aut ...

scGenLinkAggregationFaultMask

Each bit of this item describes the situation of the LAG regarding specific fault: bit 1: on indicates 'LAG connection lost' when scGenLinkAggregationFunctionalStatus=fail(2) bit 2: on indicates 'LAG partial connection' when scGenLinkAggregationFunctional ...

scGenLinkAggregationStatus

The status of this scGenLinkAggregation entry. According to RMON-2 standard (RFC 2021).

scGenPortIPAddressRspTable

Table of attributes which define general configuration information about a single SC based port.

scGenPortIPAddressRspEntry

An entry in the table, containing data about a single Port.

scGenPortIPAddressRspGroupId

Id of the group to which the port belongs.

scGenPortIPAddressRspPortId

Unique Id of the port in the scGenPortRspTable.

scGenPortIPAddressRspIpAddressIndex

Unique Id of the port in the scGenPortRspTable.

scGenPortIPAddressRspIpAddress

This MIB-item sets an IpAddress of a station that is connected to a port that performs RSP. A value of 0.0.0.0 in this Mib Item means that it does not describe an existing IpAddress. Default value is 0.0.0.0

scEthPortTable

Table of attributes which define configuration, performance and error information about ethernet ports based on the switchChip.

scEthPortEntry

An entry in the table, containing data about a single port.

scEthPortGroupId

Id of the group to which the port belongs.

scEthPortId

Unique Id of the port in the scEthPortTable.

scEthPortOctetsRec

The total number of good octets received and bad octets filtered by the port (excluding framing bits but including FCS octets). This item is the summation of scEthPortGoodOctetsRec and scEthPortBadOctets.

scEthPortPktsRec

The total number of good packets received and bad packets filtered by the port. This item is the summation of scEthPortGoodPktsRec and scEthPortBadPkts.

scEthPortGoodBroadcastPktsRec

The total number of good packets received that were directed to the broadcast address.

scEthPortGoodMulticastPktsRec

The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address.

scEthPortCRCAlignErrors

The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but were not an integral number of octets in length or had a bad Frame Check Sequence (FCS).

scEthPortOversizePkts

The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.

scEthPortFragments

The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets).

scEthPortJabber

The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and were not an integral number of octets in length or had a bad Frame Check Sequence (FCS).

scEthPortCollisions

The best estimate of the total number of collisions on this Ethernet segment.

scEthPortPkts64Octets

The total number of packets (including error packets) that were 64 octets in length (excluding framing bits but including FCS octets).

scEthPortPkts65to127Octets

The total number of packets (including error packets) that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).

scEthPortPkts128to255Octets

The total number of packets (including error packets) that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).

scEthPortPkts256to511Octets

The total number of packets (including error packets) that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).

scEthPortPkts512to1023Octets

The total number of packets (including error packets) that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).

scEthPortPkts1024to1518Octets

The total number of packets (including error packets) that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).

scEthPortGoodPktsRec

The total number of good packets received by the port.

scEthPortBadPkts

The total number of bad packets filtered by the port. This item is the summation of: scEthPortCRCAlignErrors, scEthPortOversizePkts, scEthPortFragments and scEthPortJabber.

scEthPortGoodOctetsRec

The total number of good octets of data received by the port.

scEthPortBadOctets

The total number of bad octets of data filtered by the port.

scEthPortGoodBroadcastOctetsRec

The total number of good octets received that were directed to the broadcast address.

scEthPortGoodMulticastOctetsRec

The total number of good octets received that were directed to a multicast address. Note that this number does not include octets directed to the broadcast address.

scEthPortGoodOctetsSent

The total number of good octets of data sent by the port.

scEthPortGoodPktsSent

The total number of good packets sent by the port.

scEthPortLateCollisions

The best estimate of the total number of late collisions on this Ethernet segment.

scEthPortFunctionalStatus

The functional status of the port: ok(1) - fully functional port, transmitting and receiving packets. rld(2) - receive link down condition on the port - Indicates a cable or connector failure detected by the port H/W. partition(8) - the port is in partit ...

scEthPortMode

The flow control mode of the port when operated in full duplex: halfDuplex(1) - Half duplex connection, standard mode for segment fullDuplexNoPause(2) - Full duplex connection without exchanging flow control packets fullDuplexProprietaryFC(3) - Full duple ...

scEthPortSpeed

This parameter defines the port speed: ethernet(1) and fastEthernet(2).

scEthPortAutoNegotiation

This object define if the Auto Sense /Auto Negotiation process is enable(1) or disable (2) for modules that don't support the Auto Snese mode please define the notSupported option..

scEthPortAutoNegotiationStatus

This object define the status of the Auto Negotiation process: pass: The Auto negotiation process was completed and succeeded . fail: The Auto Negotiation process failed . disable: The Auto Negotiation process is not enabled . notSupported: The Auto Negot ...

scEthPortTotalPkts

The total number of packets received and transmitted on the port (including all good and bad). This item is the summation of scEthPortPktsRec and scEthPortGoodPktsSent.

scEthPortDropEvents

The total number of events in which the probe could not count packets due to lack of resources. This number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.

scEthPortGigaPauseStatus

Indicates the status of the Flow Control as determined in the Auto Negotiation process on the Gigabit ports: noPause(1) indicates that there is no Flow Control. symmetricPause(2) indicates that both sides are working in Tx&Rx Flow Control. asymmetricPaus ...

scEthPortLower32OctetsRec

Lower 32 bit conter of the total number of octets of data received by the port.

scEthPortUpper32OctetsRec

Upper 32 bit conter of the total number of octets of data received by the port.

scEthPortLower32OctetsSent

Lower 32 bit conter of the total number of octets of data sent by the port.

scEthPortUpper32OctetsSent

Upper 32 bit conter of the total number of octets of data sent by the port.

scEthPortGoodUnicastPktsRec

The total number of good packets received that were directed to a unicast address.

scEthPortDiscardPktsRec

The total number of packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.

scEthPortUnicastPktsSent

The total number of good packets sent by the port that were directed to a unicast address.

scEthPortDiscardPktsSent

The total number of packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.

scEthPortPauseCapabilities

The Pause capabilities of a Giga port that should be advertised to the link partner when performing auto-negotiation: noFlowControl (1) - no flow control support in any direction asymTxFlowControlOnly (2) - STD 802.3x flow control frames can be sent from ...

scEthPortMulticastPktsSent

The total number of good packets sent by the port that were directed to a multicast address.

scEthPortUndersizePktsRec

The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.

scEthPortFlowControl

The flow control mode of the port

scEthGroupTable

Table of attributes which define ethernet configuration information about a single SC based group.

scEthGroupEntry

An entry in the table, containing data about a single Group.

scEthGroupId

Unique Id of the group in the scEthGroupTable. Equals the number of the slot by which the group is accessed.

scEthGroupAutoPartitionEnable

Enables/Disables the Auto-Partition mechanism in all ports of this module.

scEthGroupFefiEnable

This item enables\disables the FEFI mechanism of all Fast-Ethernet PHY's in the module. It enables\disables both the transmission and the recognition of FEFI signals.