els100-s24tx2m-mib Download

switchNumber

The total number of switches present on this system.

switchInfoTable

Table of descriptive and status information about switches in this system.

switchInfoEntry

An entry in the table, containing information about a single switch in this system.

swUnitIndex

This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.

swMainBoardHwVer

Hardware version of the main board.

swMainBoardFwVer

Firmware version of the main board.

swAgentBoardHwVer

Hardware version of the agent board.

swAgentBoardFwVer

Firmware version of the agent board.

swAgentBoardPOSTCodeVer

POST code version of the agent board.

swPortNumber

The total port number of this switch (including expansion slot).

swPowerStatus

Indicates the switch using internalPower(1), redundantPower(2) or both(3)

swExpansionSlot1

Type of expansion module in this switch slot 1.

swExpansionSlot2

Type of expansion module in this switch slot 2.

swRoleInSystem

Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.

switchOIDTable

Table of System Object Identifiers for switches in this system.

switchOIDEntry

An entry in the table, containing System Object Identifier for a single switch in this system.

switchOIDIndex

This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber. Index value 1 always represents the Master in a stacked configuration and the only device in a standalone con ...

switchOIDValue

This object contains the System Object Identifier that uniquely identifies the type of switch.

switchPortMgtTable

Table of descriptive and status information about configuration of each switch ports (including expansion slot) in this system.

switchPortMgtEntry

An entry in the table, containing information about configuration in one switch port of the switch.

swPortMgtIndex

This object identifies the port within the switch for which this entry contains information.

swPortMgtPortType

Indicates the port type is tenBaseT/hundredBaseTX(1), hundredBaseFX(2) or thousandBaseSX(3).

swPortMgtSpeedDpxAdmin

Set the port speed and duplex mode as follows: halfDuplex10(1) - 10Mbps and half duplex mode fullDuplex10(2) - 10Mbps and full duplex mode halfDuplex100(3) - 100Mbps and half duplex mode fullDuplex100(4) - 100Mbps and full duplex mode halfDuplex ...

swPortMgtSpeedDpxInUse

The operating speed and duplex mode of the switched port.

swPortMgtFlowCtrlAdmin

(1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE ...

swPortMgtFlowCtrlInUse

(1) BackPressure flow control mechanism is used. (2) IEEE 802.3 flow control mechanism is used. (3) Flow control mechanism is disabled.

systemSTAStatus

Global spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.

tftpDownloadServerIP

The IP address of a TFTP server from which a firmware image can be downloaded.

--tftpDownloadMainBoardFwFileName

-- DEFVAL { "es3526f.bin" } -- ::= { tftpDownloadMgt 2 } -- SYNTAX INTEGER { -- selected(1), -- notSelected(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTIO ...

--tftpDownloadAgentBoardFwSelected

-- "Setting this object as selected. The system will download -- agent board firmware when the download action be trigged. Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has n ...

restartOptionPOST

Setting this object as enabled. The system will do POST when it restart

restartOptionReloadFactoryDefault

Setting this object as enabled. The system will do factory reset when it restart

restartOptionKeepIpSetting

Setting this object as enabled. The system will keep IP setting when it do factory reset.

restartOptionKeepUserAuthentication

Setting this object as enabled. The system will keep user authentication setting when it do factory reset.

restartAction

Setting this object to active(1) trigger the system restart. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.

portMirrorStatus

Port mirroring function status. (1) mirroring function is enabled. (2) mirroring function is disabled.

portMirrorSnifferPort

Linear port number of sniffer port to which all frames to/from mirrored ports are sent. Frames are only mirrored if the portMirrorStatus object is set to enabled(1).

portMirrorMirroredPort

Linear port number of mirrored port. The traffic of mirrored port will be 'copied' to sniffer port.

igmpStatus

Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports. The default is enabled.

igmpQueryCount

Maximum number of queries that have not been heard on the system before the system starts taking action to solicit reports(default is 5).

igmpReportDelay

Timeout value(mins) between IGMP reports received on a port for an IP Multicast Address that can pass before the system sends an IGMP Query out the port and removes it from the list(default is 5 minutes).