enterasys-convergence-end-point-mib Download

etsysConvEndPointGlobalConfigEnable

When set to enabled(1) this object activates the current Convergence End Point configuration. When set to disabled(2) this MIB SHALL be configurable, but MUST NOT be applied, all entries will be removed from the etsysConvEndPointConnMacTable and the etsys ...

etsysConvEndPointGlobalConfigTable

This table represents all Convergence End Point types supported by this entity, and provides a default policy profile for each Convergence End Point type.

etsysConvEndPointGlobalConfigEntry

Defines the default policy to be applied when this type of Convergence End Point is detected or discovered.

etsysConvEndPointGlobalEndPointType

The Convergence End Point type. The value of this object is limited to a single enumerated bit in the ConvEndPointTypes textual convention.

etsysConvEndPointGlobalDefaultPolicyIndex

The policy that should be applied for this type of Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If no such policy index exists, then no policy will be applied when this type of Convergen ...

etsysConvEndPointProtocolConfigTable

This table provides control of Convergence End Point detection and discovery on a per interface and per Convergence End Point type basis. Maintaining the values of this table across system reboots is REQUIRED.

etsysConvEndPointProtocolConfigEntry

The current Convergence End Point detection and discovery status for an interface.

etsysConvEndPointProtocolEndPointType

The Convergence End Point type.

etsysConvEndPointProtocolEnable

When set to enabled(1), Convergence End Point detection and discovery will be enabled on this interface for the Convergence End Point type specified. When set to disabled(2), the Convergence End Points that have been discovered or detected on this interfa ...

etsysConvEndPointConnMacTable

This table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object across system reboots is NOT REQUIRED.

etsysConvEndPointConnMacEntry

Information about an individual Convergence End Point.

etsysConvEndPointConnMacMacAddress

The MAC address of this Convergence End Point.

etsysConvEndPointConnMacPortNumber

The interface on which this Convergence End Point was detected or discovered.

etsysConvEndPointConnMacEndPointType

The type of Convergence End Point described by this row.

etsysConvEndPointConnMacPolicyIndex

The policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does not currently exist, or never did exist, then a zero MUST be returned.

etsysConvEndPointConnMacDiscoveryTime

The time and date that this Convergence End Point was detected or discovered.

etsysConvEndPointConnMacFirmwareVersion

This is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string MUST be returned.

etsysConvEndPointConnMacInetAddressType

The address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'.

etsysConvEndPointConnMacInetAddress

The address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string.

etsysConvEndPointConnPortTable

This table provides a mapping from the entities interfaces to discovered Convergence End Points. Maintaining the value of this object across system reboots is NOT REQUIRED.

etsysConvEndPointConnPortEntry

Information about an individual Convergence End Point.

etsysConvEndPointConnPortMacAddress

The MAC address of the discovered or detected Convergence End Point.

etsysCEPConnMacTable

This table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object across system reboots is NOT REQUIRED.

etsysCEPConnMacEntry

Information about an individual Convergence End Point (CEP).

etsysCEPConnMacEndPointType

The type of Convergence End Point described by this row.

etsysCEPConnMacPolicyIndex

The policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does not currently exist, or never did exist, then a zero MUST be returned.

etsysCEPConnMacDiscoveryTime

The time and date that this Convergence End Point was detected or discovered.

etsysCEPConnMacFirmwareVersion

This is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string MUST be returned.

etsysCEPConnMacInetAddressType

The address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'.

etsysCEPConnMacInetAddress

The address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string.

etsysConvEndPointDetectionMaxEntries

This value represents the maximum number of entries allowed in the etsysConvEndPointDetectionTable.

etsysConvEndPointDetectionTable

A table that describes the IP address and IP port based Convergence End Point detection parameters. Packets on interfaces that are configured to detect End Points, via the etsysConvEndPointProtocolConfigTable, that are defined in this table are inspected ...

etsysConvEndPointDetectionEntry

Each entry represents a describes parameters for detecting a Convergence End Point.

etsysConvEndPointDetectionRuleIndex

The index of this conceptual row. This row represents a single rule for determining if an incoming IP packet indicates the presence of a Convergence End Point device. The lower the numerical value of the index the greater the precedence of the rule. It ...

etsysConvEndPointDetectionEndPointType

The Convergence End Point device type that a 'hit' on this rule will indicate the presence of.

etsysConvEndPointDetectionProtocol

The IP protocol type that the following port range applies to. If no bits are set then the destination port will not be evaluated as part of the detection process.

etsysConvEndPointDetectionPortLow

The low end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the low value in a range of port numbers that will be used to indicate this type of Convergence End Point. This value must be ...

etsysConvEndPointDetectionPortHigh

The high end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the high value in a range of port numbers that will be used to indicate this type of Convergence End Point. This value must b ...

etsysConvEndPointDetectionAddrType

The destination address type that will be used for Convergence End Point detection. If the address type is 'unknown', then this value will not be evaluated as part of the detection process.

etsysConvEndPointDetectionAddr

The destination IP address that will be used for Convergence End Point detection. If this address is null, then this value will not be evaluated as part of the detection process.

etsysConvEndPointDetectionAddrMaskType

The address type of the mask that will be applied to the destination IP address as part of the Convergence End Point detection process. If the address type is 'unknown', then this value will not be evaluated as part of the detection process.

etsysConvEndPointDetectionAddrMask

The destination address mask that will be used for Convergence End Point detection. If the mask is null, then this value will not be evaluated as part of the detection process.

etsysConvEndPointDetectionRowStatus

The status of this row as defined by the RowStatus textual convention. Rows in this table can only transition to 'notInService', or to 'active' if the etsysConvEndPointDetectionAddrType object and the etsysConvEndPointDetectionAddrMaskType object have the ...

etsysCEPDetectionPortConfigTable

A table of per port configuration for Convergence End Point detection. Maintaining the value of this object across system reboots is NOT REQUIRED.

etsysCEPDetectionPortConfigEntry

An entry containing per port Convergence End Point data. Only interfaces that are able to detect Convergence End Points are represented in this table.

etsysCEPPortClearUsers

Setting this object to a value of true(1) will cause all detected or discovered Convergence End Points to be removed from the following status tables: etsysConvEndPointConnMacTable etsysConvEndPointConnPortTable etsysCEPConnMacTable Setting this object to ...

etsysCEPCdpPortConfigTable

A table of per port configuration for Convergence End Point detection related to the Cisco CDP protocol. Only ports that are capable of participating in Cisco CDP protocol are represented in this table.

etsysCEPCdpPortConfigEntry

An entry containing per port Convergence End Point data. Only interfaces that are able to detect Convergence End Points are represented in this table.

etsysCEPCiscoCDPVoicePortVlan

This object controls the behavior of the remote configuration of Cisco VOIP phones via Cisco CDP. Setting this object to a value of -1 will cause the device to not attempt to remotely configure a Cisco phone using CDP. Setting this object to a value of ...

etsysConvEndPointGlobalConfigGroup

Objects which provide global control of the Convergence End Point features.

etsysConvEndPointConfigGroup

Objects which provide overrides to the global Convergence End Point controls.

etsysConvEndPointDetectionGroup

Objects that provide configuration information specific to IP, port, and address based Convergence End Point detection.

etsysConvEndPointStatusGroup

Objects that provide status information for discovered and detected Convergence End Points.

etsysConvEndPointStatusGroup2

Objects that provide status information for discovered and detected Convergence End Points.

etsysConvEndPointDetectionGroup2

Objects that provide configuration information specific to IP, port, and address based Convergence End Point detection.

etsysConvEndPointPortConfigGroup

Objects that provide per port control for discovered and detected Convergence End Points.

etsysConvEndPointCiscoVoiceVLANGroup

Objects that provide per port control for configuring Cisco VOIP phones via Cisco CDP.