enterasys-eswitch-mib Download
The Enterasys Networks Proprietary MIB module for entities implementing the Extended Switch Objects.
With the IPHost SNMP tool, you can monitor any SNMP objects of the
enterasys-eswitch-mib
. You can select a variable to monitor using the built-in IPHost MIB browser that provides you with all variables,
their current values and descriptions taken from the
enterasys-eswitch-mib
.
OID list for enterasys-eswitch-mib
- etsysESwitchAdminStatus
- DURABLE: The meanings of the values are: enabled(1) - setting this object to enabled causes the device to begin it's power up sequence and attempt to enter its operational state. If the value of this object was disabled, then the non-volatile value of th ...
- etsysESwitchRateLimitingTable
- This table allows rate limiting of multicast frames received on bridge ports. A typical application of this might be to limit a broadcast storm to the confines of the LAN connected by the bridge. All objects in this table must be saved across a system res ...
- etsysESwitchRateLimitingEntry
- An Entry (conceptual row) in the RateLimiting Table. A collection of objects containing information for enabling and configuring RateLimiting.
- etsysESwitchRateLimitSwitch
- DURABLE: By default, rate limiting will be disabled. It can be enabled by setting this object to 'true(1)'.
- etsysESwitchRateLimit
- DURABLE: This is the maximum number of rate-limited frames per second that the bridge will forward per second.
- etsysESwitchAddrFilterTable
- A list of interface entries. The number of entries is given by ifNumber, defined in MIB-II.
- etsysESwitchAddrFilterEntry
- A collection of objects containing information for a given interface.
- etsysESwitchAddressFilter
- DURABLE: A switch that controls address filtering. When true, the bridge purges the learned entries from its forwarding database, stops its learning process, and forwards only frames with destination and source addresses that have been specified via mana ...
- etsysESwitchEtherTypeTable
- A table for defining the meaning of the 'userEtherType' rows in the etsysESwitchProtocolTable.
- etsysESwitchEtherTypeEntry
- Each row defines a particular EtherType that may be used as a basis for protocol filtering and VLAN classification.
- etsysESwitchEtherTypeIndex
- A number between 1 and N that identifies a table row, and that serves to link entries in this table to those in etsysESwitchProtocolTable.
- etsysESwitchEtherTypeValue
- Defines an EtherType for use with etsysESwitchESwitchProtocolTable.
- etsysESwitchEtherTypeStatus
- This object indicates the administrative status of this entry. other(1) - This entry is currently in effect, but the conditions under which it will remain so differ from the ones described for the other enumeration values invalid(2) - Writing this value i ...
- etsysESwitchEtherTypePreempted
- If true, indicates that the switch has taken control of this row and its associated resources (e.g., to support 802.1x authentication).
- etsysESwitchProtocolTable
- A table for configuring, and obtaining information about, protocol- based filtering and VLAN assignment.
- etsysESwitchProtocolEntry
- Each row in etsysESwitchProtocolTable holds filtering instructions, or VLAN classification instructions, for one (port, protocol) pair.
- etsysESwitchProtocolReceivePort
- Identifies the receive port to which the protocol filter is to be applied. The value '0' (when allowed) represents 'all ports'.
- etsysESwitchProtocolType
- Identifies the protocol type. The switch chip in the RoamAbout M2 can recognize nine predefined high-level protocol types, and up to three user-defined EtherTypes. (Some or all EtherType filters may be reserved for use in implementing other features.) P ...
- etsysESwitchProtocolIndex
- When etsysESwitchProtocolType indicates a user-defined protocol type, this index should identify the corresponding protocol definition. That is, to say, for a 'userEtherType' row, this index should point to a row in the etsysESwitchEtherTypeTable. When et ...
- etsysESwitchProtocolConstraint
- Indicates what type of constraint the switch should apply to packets caught by the (port, protocol) filter. portMask(1) - Use the etsysESwitchProtocolAllowedToGoTo mask to determine where the packets may be forwarded. vlan(2) - Classify the packets as bel ...
- etsysESwitchProtocolAllowedToGoTo
- A port mask object indicating where packets that match this row's (port, protocol) filter are allowed to go. It applies when etsysESwitchProtocolConstraint has the value portMask(1) and this row is valid.
- etsysESwitchProtocolVlanId
- A number identifying a VLAN to which packets that match this row's (port, protocol) filter should be assigned. It applies when etsysESwitchProtocolConstraint has the value vlan(2) and this row is valid.
- etsysESwitchProtocolStatus
- This object indicates the administrative status of this entry. other(1) - This entry is currently in effect, but the conditions under which it will remain so differ from the ones described for the other enumeration values invalid(2) - Writing this value t ...
- etsysESwitchProtocolPreempted
- If true, indicates that the switch has taken control of this row and its associated resources (e.g., to support 802.1x authentication).
- etsysESwitchBaseGroup
- The basic etsysESwitch objects.
- etsysESwitchEtherTypeGroup
- A collection of objects for configuring user-defined EtherTypes.
- etsysESwitchProtocolGroup
- A collection of objects for configuring protocol-based filtering.
You can start network devices monitoring using free 30-day trial version of IPHost Network Monitor right now.
Witn IPHost SNMP monitor you can monitor network performance, audit network usage, detect network faults, or inappropriate access.
The IPHost's SNMP monitor can communicate and interact with any SNMP-enabled device.
