hub-rptr-prvt Download

rptrRxDscrptrOverFlow

missed received packets due to lack of resourcees such as descriptors or memory buffers

rptrTxDscrptrOverFlow

there is a transmit over flow

rptrMemoryErrors

there is a memory error

rptrJabberCounter

there is a jubber in one of the ports.

rptrNMSConnectionPort

NMS is connected.

rptrEDBPort

MultiHub (EDB) is connected to. if the MultiHub is not connected to the card the value returned will be 99, if the card is installed in a stand alone chassis then reading this object will return 99

rptrfmGroupTable

rptrfmGroupEntry

rptrGroupIndex

Group Number

rptrGroupGlobalStatus

the card. For more information about the meaning of the status, read the specific user manual of each card. The channel leds are encoded into 2 bytes.

rptrGroupPrevStatus

bits of the card. This object id is used mainly for traps (see Card Trap)

rptrGroupGlobalError

the value is one - there is a fault in the card.

rptrGroupJabberError

the value is one - there is a jabber event.

rptrGroupCpuError

the value is one - there is a CPU fault in the card.

rptrGroupSQE

the value is one - there is an SQE indication to the card.

rptrGroupRepeaterBlockError

the value is one - there is a fault in the repeater block.

rptrGroupAutoPartition

the value is one - at least one of the ports is in auto-partition.

rptrGroupDetachStatus

the value is one - at least one of the ports is detached.

rptrGroupGlobalCommandCode

ports. Note: in case off detach command - all port will detach except the port on which the last NMS message was received. when reading this object the value returned is always attach-all-ports(1)

rptrGroupTrapMask

then only all traps will be sent. When setting this variable to mask-warn(3) then only traps with severity of warn or fatal will be sent.When setting this variable to mask-fatal(2) then only traps with severity of fatal will be sent. When setting this var ...

rptrGroupLinkSelectHead1

and SECOND link only in Head module in the 303 type cards.

rptrGroupBackupHead1State

the backup port for Head module only in 303 cards. when set to enabled(1) the active port will be the primary port, when set to disabled(2) the active port will be the secondary port and when set to normal(3) the active port will be set by the backup algo ...

rptrGroupTailState

Tail in 303 card

rptrGroupMaxModuleNumber

Maximum Number of modules in a group.

rptrGroupPortTable

rptrGroupPortEntry

rptrGroupPIndex

Group Number

rptrGroupPortIndex

Port Number

rptrGroupPortLinkStatus

When the value is 1, link status is O.K.

rptrGroupPortRcvStatus

When a port is receiveing data the object gets the value receive(1), when the port does not receive any data the object gets the value no-receive(2)

rptrGroupPortLinkFaultCounter

a link change is detected in the port. A link change is encountered on the port whenever the link is disappearing or apearing on the port

rptrGroupPortAutoPartitionCount

there is a Auto Partition state in the port.

rptrGroupPortAutoPartitionType

Auto Partition type.

rptrGroupModuleTable

rptrGroupModuleEntry

rptrGroupMIndex

Group Number

rptrGroupModuleIndex

Module Number

rptrGroupModuleStructInfo

List of modules numnbers: eM892.330 /* BLANK */ EM892.331 /* FO single port */ EM892.332 /* FO dual port */ EM892.333 /* COAX single port */ EM892.334 /* COAX dual port */ EM892.332B /* FO dual port for Dual Homing */ EM892.335 /* 10 ...

rptrGroupModuleBackupState

backup switch (enable/disable). or let the state be as the switch is (hardware) This object applies only to the 308 card. setting this object will take effect only after the next reset or power up of the card.