cva If EM Timing Digit Duration

1.3.6.1.4.1.9.9.62.1.2.3.1.1

Outgoing DTMF digit duration in milliseconds. DEFVAL { 100 } ::= { cvaIfEMTimingEntry 1 } SYNTAX Integer32 (50..500) UNITS "milliseconds Outgoing DTMF inter-digit duration in milliseconds. DEFVAL { 100 } ::= { cvaIfEMTimingEntry 2 } SYNTAX Integer32 (10..20) UNITS "pulses per second Outgoing pulse dialing rate in pulses per second (pps). DEFVAL { 10 } ::= { cvaIfEMTimingEntry 3 } SYNTAX Integer32 (100..1000) UNITS "milliseconds Outgoing Pulse dialing inter-digit timing in milliseconds. DEFVAL { 750 } ::= { cvaIfEMTimingEntry 4 } SYNTAX Integer32 (200..2000) UNITS "milliseconds Time of Inactive seizure signal to declare call cleared. DEFVAL { 400 } ::= { cvaIfEMTimingEntry 5 } SYNTAX Integer32 (100..5000) UNITS "milliseconds Maximum time to wait from the outgoing seizure of the line to the time of sending out a wink-pulse. DEFVAL { 200 } ::= { cvaIfEMTimingEntry 6 } SYNTAX Integer32 (100..3000) UNITS "milliseconds Maximum outgoing wink duration (between the wink-pulse leading edge and trailing edge) for wink start signaling. DEFVAL { 200 } ::= { cvaIfEMTimingEntry 7 } SYNTAX Integer32 (20..2000) UNITS "milliseconds Minimum time to wait from outgoing seizure to out-dialing digits for delay start signaling. DEFVAL { 300 } ::= { cvaIfEMTimingEntry 8 } SYNTAX Integer32 (100..5000) UNITS "milliseconds Maximum time to wait from outgoing seizure to out-dialing digits. If the far end does not allow to send digits after the duration specified in the object, a reorder tone will be sent to the calling party. DEFVAL { 2000 } ::= { cvaIfEMTimingEntry 9 } SYNTAX Integer32 (0 | 140..5000) UNITS "milliseconds Minimum delay-dial pulse duration for incoming call. If the value of this object is 0, then no delay-dial is sent to the far end for the incoming call. DEFVAL { 140 } ::= { cvaIfEMTimingEntry 10 } SYNTAX Integer32 (0..10000) UNITS "milliseconds The hangover time used to determine the casethere is no more voice packet arrived. DEFVAL { 250 } ::= { cvaIfEMTimingEntry 11 } SYNTAX Integer32 (-1 | 5..60000) UNITS "seconds LMR port tear down timeout. This object is relevant to the waiting time of teardown call on LMR port. if the value of this object is '-1', then the timeout is disable. DEFVAL { 1800 } ::= { cvaIfEMTimingEntry 12 } SYNTAX Integer32 (0..30) UNITS "minutes This object signifies LMR port maxinum transmit time. This object is relevant to how long LMR port can continue transmit voice packet without pause. DEFVAL { 0 } ::= { cvaIfEMTimingEntry 13 } SYNTAX Integer32 (0..30) UNITS "minutes This object signifies LMR port maxinum receive time. This object is relevant to how long LMR port can continue receive voice packet without pause. DEFVAL { 0 } ::= { cvaIfEMTimingEntry 14 } SYNTAX Integer32 (0..1500) UNITS "milliseconds This object is relevant to how long DSP will delay sending the voice packet to the LMR port. DEFVAL { 0 } ::= { cvaIfEMTimingEntry 15 } --**************************************************************************** -- The Foreign Exchange Office (FXO) Standard Configuration Table --**************************************************************************** -- This table is used to configure the FXO signaling and number of rings -- for the FXO interface. SYNTAX SEQUENCE OF CvaIfFXOCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION The FXO standard configuration table. It contains FXO configuration parameters, one entry per FXO interface. The configuration information of this table is set by hardware with its default setting or CLI during the hardware installation time. ::= { cvaIfFXOObjects 1 } SYNTAX CvaIfFXOCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry in the standard configuration table for each FXO interface.