With IPHost Network Monitor you can run simple snmp requests against a Cisco device in your network.
x21LineEnable
x21 Line Enable
1.3.6.1.4.1.351.110.4.5.1.1.1.2
This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify Default is enable. ::= { x21CnfGrpEntry 2 } SYNTAX INTEGER { dte (1), dce (2), dteST (3) } MAX-ACCESS read-write STATUS current DESCRIPTION This variable indicates the type X21 line type. The line-type affects the clock -- the DCE device always provides the clock and DTE accepts it. dteST is only applicable to V.35 interfaces Default is DTE. ::= { x21CnfGrpEntry 3 } SYNTAX INTEGER { r48Kbps(1), r56Kbps(2), r64Kbps(3), r112Kbps(4), r128Kbps(5), r168Kbps(6), r192Kbps(7), r224Kbps(8), r256Kbps(9), r280Kbps(10), r320Kbps(11), r336Kbps(12), r384Kbps(13), r392Kbps(14), r448Kbps(15), r512Kbps(16), r768Kbps(17), r1024Kbps(18), r1536Kbps(19), r1544Kbps(20), r1792Kbps(21), r1920Kbps(22), r1984Kbps(23), r2048Kbps(24), r3097Kbps(25), r3157Kbps(26), r4096Kbps(27), r4645Kbps(28), r4736Kbps(29), r6195Kbps(30), r6315Kbps(31), r7744Kbps(32), r7899Kbps(33), r8192Kbps(34), r9289Kbps(35), r9472Kbps(36), r10240Kbps(37), r10890Kbps(38), r11060Kbps(39), r12390Kbps(40), r12630Kbps(41), r13900Kbps(42), r14220Kbps(43), r14340Kbps(44), r15490Kbps(45), r15800Kbps(46), r16380Kbps(47), r20030Kbps(48), r24990Kbps(49), r52Mbps(50), -- FRSM_VHS added for frsm_vhs r17370Kbps(51), r18950Kbps(52), r20530Kbps(53), r22100Kbps(54), r23680Kbps(55), -- -- n*T1 rates. Added for FRSM_VHS -- note that 1.544Kbps is already enumerated above -- r3088Kbps(56), r4632Kbps(57), r6176Kbps(58), r7720Kbps(59), r9264Kbps(60), r10808Kbps(61), r12352Kbps(62), r13896Kbps(63), r15440Kbps(64), r16984Kbps(65), r18528Kbps(66), r20072Kbps(67), r21616Kbps(68), r23160Kbps(69), r24704Kbps(70), r26248Kbps(71), r27792Kbps(72), r29336Kbps(73), r30880Kbps(74), r32424Kbps(75), r33968Kbps(76), r35512Kbps(77), r37056Kbps(78), r38600Kbps(79), r40144Kbps(80), r41688Kbps(81), r43232Kbps(82), r44776Kbps(83), r46320Kbps(84), r47864Kbps(85), r49408Kbps(86), r50952Kbps(87), -- -- n*E1 rates. Added for FRSM_VHS. -- r6144Kbps(88), r12288Kbps(89), r14336Kbps(90), r16384Kbps(91), r18432Kbps(92), r20480Kbps(93), r22528Kbps(94), r24576Kbps(95), r26624Kbps(96), r28672Kbps(97), r30720Kbps(98), r32768Kbps(99), r34816Kbps(100), r36864Kbps(101), r38912Kbps(102), r40960Kbps(103), r43008Kbps(104), r45056Kbps(105), r47104Kbps(106), r49152Kbps(107), r51200Kbps(108) } MAX-ACCESS read-write STATUS current DESCRIPTION This variable configures the X.21/HSSI/V.35 line-rate. Note that enumerations 51 through 108 are supported only by FRSM-HS2/HS2B card. default is r48Kbps on FRSM-HS2B-12IN1 default is r52Mbps on FRSM-HS2/HS2B-HSSI ::= { x21CnfGrpEntry 4 } SYNTAX INTEGER { x21NoLoop (1), x21DiagnosticMetallicLoop (2), x21DiagnosticFrontcardLoop (3), x21RemoteLoop (4), v35MetallicLoop (5) } MAX-ACCESS read-write STATUS current DESCRIPTION This variable represents the loopback state x21NoLoop Not in the loopback state. Normal traffic can be sent x21DiagnosticMetallicLoop Loopbacks the line on the back-card towards the Network. x21DiagnosticFrontcardLoop Loopbacks the line on the frontcard toward the Network. x21RemoteLoop The remote NTU is in the loop back mode. In this state, the FRSM-HS1 is sending the loopback code to remote NTU. Default is x21NoLoop. Note: Before going into one of the loopbacks the state should be x21NoLoop. ::= { x21CnfGrpEntry 5 } SYNTAX INTEGER { x21NoCode (1), x21SendLoopACode (2), x21SendLoopBCode (3), x21SendLocalLoopCode (4), x21SendRemoteLoopCode (5), x21SendUnLoopCode (6) } MAX-ACCESS read-write STATUS current DESCRIPTION This variable indicates what type of code is being sent across the X.21/HSSI interface by the device. The values mean: x21NoCode: No loopback. x21SendLoopACode: Start sending Loop A code. Valid only if the backcard is HSSI and the line-type is DTE. This command loops the line module of the remote device. x21SendLoopBCode: Start sending Loop B code. Valid only if the backcard is HSSI and the line-type is DTE. This command loops the digital section of the remote device. x21SendLocalLoopCode: Start sending CCITT X.21 Loopback Type 3 code. This is valid only if the backcard is X.21 type. x21SendRemoteLoopCode: Start sending CCITT X.21 Loopback Type 2 code. This is valid only if the backcard is X.21 type. x21SendUnLoopCode: Sending a loopback termination request. Valid for both HSSI and X.21 lines. To execute any of the loop-codes the x21LineLoopbackCommand should be set to x21RemoteLoop. Once the x21SendUnLoopCode succeeds the x21LineLoopbackCommand would transition back to x21NoLoop state. Default is x21NoCode.
Back to CISCO-WAN-FR-X21-MIB MIB page.
IPHost Network monitor allows you to monitor x21LineEnable on Cisco device via the SNMP protocol. Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring Cisco optical switches right now.