CISCO-WAN-FR-X21-MIB Download

x21CnfGrpTable

The X21 Configuration table. The table size is given by the value of x21LineNumofValidEntries.

x21CnfGrpEntry

An entry in the X21 Configuration table.

x21LineNum

This object is the identifier of a X.21 interface. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2. FRSM-HS2B-12IN1 supports a range from 1 to 8.

x21LineEnable

This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify Default is enable. ::= { x21CnfGrpEntry 2 } SYNTAX INTEGER { dte (1), dce (2), dteST (3) } MAX-ACCESS read-write STATUS current DESCRIPTION This variable indicat ...

x21LineLoopbackCodeDetection

Enable detection of line Loopback Codes. The loopback detection is implemented only in HSSI DCE mode. Default is codeDetectDisabled.

x21ConnectorType

back card type This object is not used by FRSM-HS2/HS2B ::= { x21CnfGrpEntry 8 } SYNTAX INTEGER { nonInvertedAndNotLooped (1), invertedAndNotLooped (2), nonInvertedAndLooped (3), invertedAndLooped (4) } MAX-ACCESS read-write STATUS current ...

x21LineInterfaceType

This object indicates serial interface type. Default is hssi(1). This object is not is configurable in FRSM-HS2 and FRSM-HS2B-HSSI. It will be set to hssi(1) by default for these cards This object is configurable in FRSM-H2B-12IN1. Default is v35(3).

x21ClkFrequencyThreshold

This object indicates user configurable percentage of clock frequency, which is used by DTE clock monitoring to declare clock rate out of bound alarm. This object is valid only for X.21/v.35/HSSI DTE interfaces. This object is supported by FRSM-HS2 and FR ...

serialLineRate

Line rate for X.21/HSSI/V.35 interfaces in bps. This object is supported only by FRSM-HS2/B card, only multiples of 1000 are accepted. Default is 48Kbps for X.21/V.35 interfaces and 51840Kbps for HSSI interface.

serialLineRateVariation

This object indicates line rate variation of HSSI/X.21/V.35 DCE interfaces in ppm (parts per million). i.e. clock generated from DCE hardware interface = (serialLineRate +/- (serialLineRateVariation * 10^6)/ serialLineRate) This object is supported only ...

x21LineNumofValidEntries

The number of X.21/HSSI configuration entries (regardless of their current configuration) in the x21ConfigTable table.

frPortCnfX21PortGrpTable

The config table is for X.21/HSSI logical port interface ::= { frPortCnfX21PortGrp 1 } SYNTAX FrPortCnfX21PortGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry for logical port.

x21portNum

This is logical port number. The HSSI backcard can support upto 3 ports. The X.21 back card can support 4 logical ports.

x21portLineNum

This represents the line number. On FRSM-HS1 the HSSI can support 3 lines and X.21 4 lines.

x21portRowStatus

This variable adds, deletes, or modifies the port 1- add 2 - delete 3 - modify Default is add.

x21portFlagsBetweenFrames

Number of flags transmitted between two consecutive HDLC frames. Default is 1 flag.

x21portEqueueServiceRatio

Number of times queue 1 is serviced for every time queue 2 is serviced. Default is 1.

x21portSpeed

Port speed in kbps. At present it is same as line speed.

x21portAdmin

This object is used for administratively changing the status of the port. Up/down used to up and down the port. Default is the up state.

x21portType

This represents port type. The processing of the frames depends on the type of the port.

x21portSvcStatus

This represents SVC status.

x21portSvcInUse

This represents port SVC in use.

x21portSvcShareLcn

This represents port type.

x21portSvcLcnLow

This represents low end of reserved LCN for SVC.

x21portSvcLcnHigh

This represents high end of reserved LCN for SVC.

x21portSvcDlciLow

This represents low end of reserved DLCI for SVC.

x21portSvcDlciHigh

This represents high end of reserved DLCI for SVC.

x21portDeleteSvcs

Setting this object to 1 indicates that all the SVC connections on the given port has to be deleted.

x21portIngrSvcBandW

This represents Ingress Bandwidth reserve for SVC.

x21portEgrSvcBandW

This represents Egress Bandwidth reserve for SVC.

x21AlmCnfGrpTable

The FRSM-HS1/HS2 interface alarm configuration table.

x21AlmCnfGrpEntry

An entry in the X.21/HSSI Alarm Configuration table.

x21AlmCnfLineNum

X.21/HSSI line number. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2. FRSM-HS2B-12IN1 supports a range from 1 to 8.

x21Severity

This variable is used to setup the severity of LOS(Loss of Signal) or clock mismatch alarm. Whenever the above condition arises, the FRSM-HS1/HS2/HS2B will send the alarm with appropriate status.

x21AlmGrpTable

The X.21/HSSI interface alarm configuration table.

x21AlmGrpEntry

An entry in the X21 Alarm table

x21AlmLineNum

This object is the identifier (line number) of a X.21/HSSI interface. The value for this object must be same as the value of x21LineNum.

x21LineAlarmState

This variable is a bitmap of the X21 Line ALarms on the FRSM-HS1. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 C/I signal is OFF (also used to indicate LOS) 1 Clock r ...

x21AlarmClrButton

This variable is used to clear all the alarms for the line. 1 = No action 2 = Clear alarm.

ciscoWanFrX21PortGroup

The collection of objects which are applicable for X21 ports in frame relay.

ciscoWanFrX21LineGroup

The collection of objects which are related to x21 lines.

ciscoWanFrX21AlarmConfGroup

The collection of objects which are related to x21 lines.

ciscoWanFrX21AlarmGroup

The collection of objects which are related to x21 lines.