rfc1315 Download

frDlcmiTable

The Parameters for the Data Link Connection Management Interface for the frame relay service on this interface.

frDlcmiEntry

The Parameters for a particular Data Link Con- nection Management Interface.

frDlcmiIfIndex

The ifIndex value of the corresponding ifEn- try.

frDlcmiState

This variable states which Data Link Connec- tion Management scheme is active (and by impli- cation, what DLCI it uses) on the Frame Relay interface.

frDlcmiAddress

This variable states which address format is in use on the Frame Relay interface.

frDlcmiAddressLen

This variable states which address length in octets. In the case of Q922 format, the length indicates the entire length of the address in- cluding the control portion.

frDlcmiPollingInterval

This is the number of seconds between succes- sive status enquiry messages.

frDlcmiFullEnquiryInterval

Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage.

frDlcmiErrorThreshold

This is the maximum number of unanswered Status Enquiries the equipment shall accept be- fore declaring the interface down.

frDlcmiMonitoredEvents

This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station receives 'ErrorThreshold' number of errors, the interface is marked as down.

frDlcmiMaxSupportedVCs

The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. In response to a SET, if a value less than zero or higher than the agent's maximal capability is configured, the agent should respond ...

frDlcmiMulticast

This indicates whether the Frame Relay inter- face is using a multicast service.

frCircuitTable

A table containing information about specific Data Link Connection Identifiers and corresponding virtual circuits.

frCircuitEntry

The information regarding a single Data Link Connection Identifier.

frCircuitIfIndex

The ifIndex Value of the ifEntry this virtual circuit is layered onto.

frCircuitDlci

The Data Link Connection Identifier for this virtual circuit.

frCircuitState

Indicates whether the particular virtual cir- cuit is operational. In the absence of a Data Link Connection Management Interface, virtual circuit entries (rows) may be created by set- ting virtual circuit state to 'active', or deleted by chang ...

frCircuitReceivedFECNs

Number of frames received from the network in- dicating forward congestion since the virtual circuit was created.

frCircuitReceivedBECNs

Number of frames received from the network in- dicating backward congestion since the virtual circuit was created.

frCircuitSentFrames

The number of frames sent from this virtual circuit since it was created.

frCircuitSentOctets

The number of octets sent from this virtual circuit since it was created.

frCircuitReceivedFrames

Number of frames received over this virtual circuit since it was created.

frCircuitReceivedOctets

Number of octets received over this virtual circuit since it was created.

frCircuitCreationTime

The value of sysUpTime when the virtual cir- cuit was created, whether by the Data Link Con- nection Management Interface or by a SetRe- quest.

frCircuitLastTimeChange

The value of sysUpTime when last there was a change in the virtual circuit state

frCircuitCommittedBurst

This variable indicates the maximum amount of data, in bits, that the network agrees to transfer under normal conditions, during the measurement interval.

frCircuitExcessBurst

This variable indicates the maximum amount of uncommitted data bits that the network will at- tempt to deliver over the measurement interval. By default, if not configured when creating the entry, the Excess Information Burst Size is set to the value of ...

frCircuitThroughput

Throughput is the average number of 'Frame Re- lay Information Field' bits transferred per second across a user network interface in one direction, measured over the measurement inter- val. If the configured committed burst rate and throughput ...

frErrTable

A table containing information about Errors on the Frame Relay interface.

frErrEntry

The error information for a single frame relay interface.

frErrIfIndex

The ifIndex Value of the corresponding ifEn- try.

frErrType

The type of error that was last seen on this interface.

frErrData

An octet string containing as much of the er- ror packet as possible. As a minimum, it must contain the Q.922 Address or as much as was delivered. It is desirable to include all in- formation up to the PDU.

frErrTime

The value of sysUpTime at which the error was detected.

frTrapState

This variable indicates whether the system produces the frDLCIStatusChange trap.