CISCO-DOT11-HT-MAC-MIB Download

cD11HtMacStationConfigTable

This table represents the MAC configuration parameters of 802.11n interfaces. There exists in this table, an entry corresponding to each entry in dot11PhyOperationTable where dot11PHYType equals 'ht'(7).

cD11HtMacStationConfigEntry

Each Entry represents a conceptual row in ccD11HtMacStationConfigTable and corresponds to the MAC configuration parameters of an 802.11n interface.

cD11HtMacOperationalMCSSet

This object represents the set of MCS at which the station may transmit data. Each bit represents an MCS index and corresponds to a particular data rate. Each MCS shall be within the range from 0 to 127, and shall be supported for receiving data. This va ...

cD11HtMacMIMOPowerSave

This object represents the operational power save state of MIMO. The semantics are defined as follows. 'static' - The dot11 interface is operating in static MIMO Power Save mode and hence, other stations should not send MIMO packets destined to this dot1 ...

cD11HtMacNDelayedBlockAckImplemented

This object, when 'true', indicates that the dot11 interface supports the No-Ack option of the Delayed Block Acknowledgement.

cD11HtMacMaxAMSDULength

This object represents the supported maximum size of A-MSDU. 'amsduSize3839' - This indicates a maximum size of 3839 octets. 'amsduSize7935' - This indicates a maximum size of 7935 octets.

cD11HtMacPSMPImplemented

This object, when 'true', indicates that the dot11 interface is capable of supporting PSMP.

cD11HtMacSTBCControlFrameImplemented

This object, when 'true', indicates that the dot11 interface is capable of processing the received STBC control frames.

cD11HtMacLsigTxOpProtectImplemented

This object, when 'true', indicates that the dot11 interface is capable of supporting L-SIG TXOP Protection option.

cD11HtMacMaxRxAMPDUFactor

This object is used to compute the maximum length of the A-MPDU the STA can receive, as follows. maximum length of A-MPDU in octets = 2 ^ ( 13 + cD11HtMacMaxRxAMPDUFactor ) -1.

cD11HtMacMPDUDensity

This object represents the minimum time between the start of adjacent MPDUs within an A-MPDU. This time is measured at the PHY service access-point; the number of bytes between the start of two consecutive MPDUs in A-MPDU shall be equal or greater than (M ...

cD11HtMacPCOImplemented

This object, when 'true', indicates that the dot11 interface is capable of supporting Phased coexistence operation.

cD11HtMacTransitionTime

This object indicates that the minimum transition time within which the STA can switch between 20 MHz channel width and 40 MHz channel width with a high probability.

cD11HtMacMCSFeedbackImplemented

This object indicates the MCS feedback capability supported on this 802.11n interface. The semantics are as follows. 'none' - The station does not provide MCS feedback through this interface. 'unsolicited' - The station provides only unsolicited MCS feedb ...

cD11HtMacAMSDUEnable

This object represents whether this 802.11n radio can transmit / receive A-MSDUs.

cD11HtMacAMPDUEnable

This object represents whether this 802.11n radio can transmit / receive A-MPDUs.

cD11HtMacOperationTable

This table represents the operational parameters of 802.11n interfaces. Entries in this table are created automatically by the agent corresponding to each 802.11n interface. There exists in this table, an entry corresponding to each entry in dot11PhyOpera ...

cD11HtMacOperationEntry

A conceptual row in cD11HtMacOperationTable and represents the operational parameters of an 802.11n interface.

cD11HtMacOperatingMode

This object represents the level of protection to be provided to the data transmissions of 802.11n radios. The semantics are as follows. 'pureHt' - No protection will be provided to the high throughput tranmissions in the BSS started on this interface. T ...

cD11HtMacRIFSMode

This object, when set to 'true', indicates that RIFS mode is allowed in the BSS.

cD11HtMacPSMPControlledAccess

This object, when set to 'true', indicates that the AP accepts associations only from PSMP-enabled clients.

cD11HtMacServiceIntervalGranularity

This object represents the service interval granularity to be used for scheduled PSMP. The value of the granularity is given by (cD11HtMacServiceIntervalGranularity+1)*5 milliseconds.

cD11HtMacDualCTSProtection

This object, when set to 'true', indicates that the AP uses dual CTS protection to protect the regular and the STBC transmissions.

cD11HtMacLSigTxOpFullProtectionEnabled

This object, when set to 'true', indicates that the LSIG-TXOP Protection is currently enabled on the AP.

cD11HtMacNonGFEntitiesPresent

This object, when set to 'true', indicates that Non-GreenField clients are present in the BSS.

cD11HtMacPCOActivated

This object, when set to 'true', indicates that the PCO is activated.

cD11HtMacPCO20MaxDuration

This object represents the maximum duration of 20 MHz phase in TU under PCO operation. The value of this object shall be equal to or larger than cD11HtMacPCO20MinDuration.

cD11HtMacPCO40MaxDuration

This object represents the maximum duration of 40 MHz phase in TU under PCO operation. The value of this object shall be equal to or larger than cD11HtMacPCO40MinDuration.

cD11HtMacPCO20MinDuration

This object represents the minimum duration of 20 MHz phase in TU under PCO operation.

cD11HtMacPCO40MinDuration

This object represents the minimum duration of 40 MHz phase in TU under PCO operation.

ciscoDot11HtMacStationConfigGroup

This collection of objects represent the MAC configuration parameters of 802.11n radio interfaces.

ciscoDot11HtMacOperationsGroup

This collection of objects represent the MAC operational parameters of 802.11n radio interfaces.