CISCO-DOT3-OAM-MIB Download

cdot3OamTable

This table contains the primary controls and status for the OAM capabilities of an Ethernet like interface. There will be one row in this table for each Ethernet like interface in the system that supports the OAM functions defined in [802.3ah]. ::= { cdo ...

cdot3OamOperStatus

At initialization and failure conditions, two OAM entities on the same full-duplex Ethernet link begin a discovery phase to determine what OAM capabilities may be used on that link. The progress of this initialization is controlled by the OAM sublayer. T ...

cdot3OamMode

This object configures the mode of OAM operation for this Ethernet like interface. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. These two modes differ in that active mode provides additional capabilities to initiate monitoring a ...

cdot3OamMaxOamPduSize

The largest OAMPDU that the OAM entity supports. OAM entities exchange maximum OAMPDU sizes and negotiate to use the smaller of the two maximum OAMPDU sizes between the peers. This value is determined by the local implementation. REFERENCE "[802.3ah], ...

cdot3OamConfigRevision

The configuration revision of the OAM entity as reflected in the latest OAMPDU sent by the OAM entity. The config revision is used by OAM entities to indicate configuration changes have occurred which might require the peer OAM entity to re-evaluate whet ...

cdot3OamFunctionsSupported

The OAM functions supported on this Ethernet like interface. OAM consists of separate functional sets beyond the basic discovery process which is always required. These functional groups can be supported independently by any implementation. These values ...

cdot3OamPeerTable

This table contains information about the OAM peer for a particular Ethernet like interface. OAM entities communicate with a single OAM peer entity on Ethernet links on which OAM is enabled and operating properly. There is one entry in this table for eac ...

cdot3OamPeerVendorOui

The OUI of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The OUI can be used to identify the vendor of the remote OAM entity. This value is initialized to zero before any Local Information TLV is recei ...

cdot3OamPeerVendorInfo

The Vendor Info of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The vendor information field is within the Local Information TLV, and can be used to determine additional information about the peer enti ...

cdot3OamPeerMode

The mode of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The mode of the peer can be determined from the Configuration field in the Local Information TLV of the last Information OAMPDU received from th ...

cdot3OamPeerMaxOamPduSize

The maximum size of OAMPDU supported by the peer as reflected in the latest Information OAMPDU received with a Local Information TLV. Ethernet OAM on this interface must not use OAMPDUs that exceed this size. The maximum OAMPDU size can be determined f ...

cdot3OamPeerConfigRevision

The configuration revision of the OAM peer as reflected in the latest OAMPDU. This attribute is changed by the peer whenever it has a local configuration change for Ethernet OAM this interface. The configuration revision can be determined from the Revis ...

cdot3OamPeerFunctionsSupported

The OAM functions supported on this Ethernet like interface. OAM consists of separate functionality sets above the basic discovery process. This value indicates the capabilities of the peer OAM entity with respect to these functions. This value is initi ...

cdot3OamLoopbackTable

This table contains controls for the loopback state of the local link as well as indicating the status of the loopback function. There is one entry in this table for each entry in cdot3OamTable that supports loopback functionality (where cdot3OamFunction ...

cdot3OamLoopbackEntry

An entry in the table, containing information on the loopback status for a single Ethernet like interface. Entries in the table are automatically created whenever the local OAM entity supports loopback capabilities. The loopback status on the interface ...

cdot3OamLoopbackIgnoreRx

Since OAM loopback is a disruptive operation (user traffic does not pass), this attribute provides a mechanism to provide controls over whether received OAM loopback commands are processed or ignored. When the value is ignore(1), received loopback comman ...

cdot3OamStatsTable

This table contains statistics for the OAM function on a particular Ethernet like interface. There is an entry in the table for every entry in the cdot3OamTable. The counters in this table are defined as 32-bit entries to match the counter size as defined ...

cdot3OamInformationRx

A count of the number of Information OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. REFERENCE " ...

cdot3OamUniqueEventNotificationTx

A count of the number of unique Event OAMPDUs transmitted on this interface. Event notifications may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. Duplicate Eve ...

cdot3OamUniqueEventNotificationRx

A count of the number of unique Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. Duplicat ...

cdot3OamDuplicateEventNotificationTx

A count of the number of duplicate Event OAMPDUs transmitted on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. A d ...

cdot3OamDuplicateEventNotificationRx

A count of the number of duplicate Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. A dupl ...

cdot3OamLoopbackControlTx

A count of the number of Loopback Control OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. REFER ...

cdot3OamLoopbackControlRx

A count of the number of Loopback Control OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. REFERENC ...

cdot3OamVariableRequestTx

A count of the number of Variable Request OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. REFER ...

cdot3OamVariableRequestRx

A count of the number of Variable Request OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. REFERENC ...

cdot3OamVariableResponseTx

A count of the number of Variable Response OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. REFE ...

cdot3OamVariableResponseRx

A count of the number of Variable Response OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. REFEREN ...

cdot3OamOrgSpecificTx

A count of the number of Organization Specific OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. ...

cdot3OamOrgSpecificRx

A count of the number of Organization Specific OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime. REF ...

cdot3OamUnsupportedCodesTx

A count of the number of OAMPDUs transmitted on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuity ...

cdot3OamUnsupportedCodesRx

A count of the number of OAMPDUs received on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTim ...

cdot3OamFramesLostDueToOam

A count of the number of frames that were dropped by the OAM multiplexer. Since the OAM multiplexer has multiple inputs and a single output, there may be cases where frames are dropped due to transmit resource contention. This counter is incremented whe ...

cdot3OamEventConfigTable

Ethernet OAM includes the ability to generate and receive Event Notification OAMPDUs to indicate various link problems. This table contains the mechanisms to enable Event Notifications and configure the thresholds to generate the standard Ethernet OAM eve ...

cdot3OamErrSymPeriodWindowLo

The two objects cdot3OamErrSymPeriodWindowHi and cdot3OamErrSymPeriodWindowLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as cdot3OamErrSymPeriodWindow = ((2^32)* ...

cdot3OamErrSymPeriodThresholdHi

The two objects cdot3OamErrSymPeriodThresholdHi and cdot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as cdot3OamErr ...

cdot3OamErrSymPeriodThresholdLo

The two objects cdot3OamErrSymPeriodThresholdHi and cdot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this event. This is defined as cdot3OamErr ...

cdot3OamErrSymPeriodEvNotifEnable

If true, the OAM entity should send an Event Notification OAMPDU when an Errored Symbol Period Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notific ...

cdot3OamErrFramePeriodThreshold

The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an ...

cdot3OamErrFramePeriodEvNotifEnable

If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Period Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifica ...

cdot3OamErrFrameThreshold

The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This can be used as an ...

cdot3OamErrFrameEvNotifEnable

If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications ( ...

cdot3OamErrFrameSecsSummaryThreshold

The number of errored frame seconds that must occur for this event to be triggered. The default value is one errored frame second. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of every window). This ...

cdot3OamErrFrameSecsEvNotifEnable

If true, the local OAM entity should send an Event Notification OAMPDU when an Errored Frame Seconds Event occurs. By default, this object should have the value true for Ethernet like interfaces that support OAM. If the OAM layer does not support event n ...

cdot3OamEventLogTimestamp

The value of sysUpTime at the time of the logged event. For locally generated events, the time of the event can be accurately retrieved from sysUpTime. For remotely generated events, the time of the event is indicated by the reception of the Event Notif ...

cdot3OamEventLogOui

The OUI of the entity defining the object type. All IEEE 802.3 defined events (as appearing in [802.3ah] except for the Organizationally Unique Event TLVs) use the IEEE 802.3 OUI of 0x0180C2. Organizations defining their own Event Notification TLVs incl ...

cdot3OamEventLogType

The type of event that generated this entry in the event log. When the OUI is the IEEE 802.3 OUI of 0x0180C2, the following event types are defined: erroredSymbolEvent(1), erroredFramePeriodEvent (2), erroredFrameEvent(3), erroredFrameSecondsEvent(4), lin ...

cdot3OamEventLogLocation

Whether this event occurred locally (local(1)), or was received from the OAM peer via Ethernet OAM (remote(2)). ::= { cdot3OamEventLogEntry 5 } SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION If the event represents a threshol ...

cdot3OamEventLogWindowLo

If the event represents a threshold crossing event, the two objects cdot3OamEventWindowHi and cdot3OamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (for example, 5, whe ...

cdot3OamEventLogThresholdHi

If the event represents a threshold crossing event, the two objects cdot3OamEventThresholdHi and cdot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (for example, 10, when 11 occurr ...

cdot3OamEventLogThresholdLo

If the event represents a threshold crossing event, the two objects cdot3OamEventThresholdHi and cdot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (for example, 10, when 11 occurr ...

cdot3OamEventLogValue

If the event represents a threshold crossing event, this value indicates the value of the parameter within the given window that generated this event (for example, 11, when 11 occurrences happened in 5 seconds while the threshold was 10). Otherwise, this ...

cdot3OamEventLogRunningTotal

Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-threshold crossing events, the number of events (cdot3OamL ...

cdot3OamEventLogEventTotal

Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-threshold crossing events, the number of events (cdot3OamL ...

cdot3OamControlGroup

A collection of objects providing the abilities, configuration, and status of an Ethernet OAM entity.

cdot3OamPeerGroup

A collection of objects providing the abilities, configuration, and status of a peer Ethernet OAM entity.

cdot3OamStatsBaseGroup

A collection of objects providing the statistics for the number of various transmit and receive events for OAM on an Ethernet like interface. Note that all of these counters must be supported even if the related function (as described in cdot3OamFunction ...

cdot3OamLoopbackGroup

A collection of objects for controlling the OAM remote loopback function.

cdot3OamErrSymbolPeriodEventGroup

A collection of objects for configuring the thresholds for an Errored Symbol Period Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.

cdot3OamErrFramePeriodEventGroup

A collection of objects for configuring the thresholds for an Errored Frame Period Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.

cdot3OamErrFrameEventGroup

A collection of objects for configuring the thresholds for an Errored Frame Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.

cdot3OamErrFrameSecsSummaryEventGroup

A collection of objects for configuring the thresholds for an Errored Frame Seconds Summary Event. Each [802.3ah] defined Event Notification TLV has its own conformance group because each event can be implemented independently of any other.

cdot3OamFlagEventGroup

A collection of objects for configuring the sending OAMPDUs with the critical event flag or dying gasp flag enabled.

cdot3OamEventLogGroup

A collection of objects for configuring the thresholds for an Errored Frame Seconds Summary Event and maintaining the event information.