CISCO-MEGACO-EXT-MIB Download

cmedxGatewayConfigTable

The Cisco media gateway configuration extended table defines the parameters related to the configuration of the media gateway in H.248 protocol. Each entry represents an instance of an H.248 Gateway Link.

cmedxGatewayConfigEntry

An entry containing additional H.248 protocol related configuration applicable to a media gateway. The following objects must be provided when the entry is created, and they can not be modified after the entry becomes active: cmedxGatewayMgcGroupIndex, cm ...

cmedxGatewayMgcGroupIndex

This object specifies the MGC group parameters associated with MGC group index. Those parameters are for the communication between this media gateway and the MGCs in the group. The value of this object is the same as cMgcGrpIndex of cMgcGrpParamTable.

cmedxGatewayIpAddressIndex

This object specifies the media gateway IP address. It is the index of the entry in cMediaGwIpConfigTable which defines the media gateway address over control type PVC.

cmedxGatewayAssociationId

This object indicates the unique identification of the H.248 association assigned by the H.248 Stack.

cmedxGatewayMaxContexts

Maximum number of contexts is allowed in this media gateway link.

cmedxGatewayMaxTermsInContext

Maximum number of terminations per context in this media gateway link.

cmedxGatewayMgExecTime

This object specifies the interval within which the MGC expects a response to any transaction from the MG (exclusive of network delay specified by the object cmedxGatewayInitialRtt).

cmedxGatewayMgcExecTime

This object specifies the interval within which the MG should expects a response to any transaction from the MGC (exclusive of network delay specified by the object cmedxGatewayInitalRtt).

cmedxGatewayProvisionRespTime

This object specifies the time within which to expect a Pending Response if a transaction cannot be completed in the media gateway and in the MGCs of the media gateway link. The value of this object should be less than the value of cmedxGatewayMgExecTime ...

cmedxGatewayNumConnRetries

The number of times the media gateway retries to connect to MGC before it sends out disconnect command.

cmedxGatewayMaxWaitingDelay

When a media gateway is powered on, it should initiate a restart timer to a random value, uniformly distributed between 0 and the value specified in this object (the maximum waiting delay, MWD). After restart timer timeout, the media gateway can initiate ...

cmedxGatewayRestartDelay

This object specifies The time delay before the media gateway accept any call from MGC after it sends the command 'ServiceChange' with a 'Restart'.

cmedxGatewayRespRetentionTime

This object specifies the time till which the responses should be retained before they are sent if they receive a repetition of a transaction that is still being executed.

cmedxGatewayInitialRtt

Initial round-trip time for the H.248 transaction to be responded. It reflects the network delay time.

cmedxGatewayInactivityTime

This object specifies the the period of silence between messages from MGC. If the period of silence exceeds the value of this object, then a Notify command with inactive MGC event is generated from the media gateway. The value of 0 is to disable the inact ...

cmedxGatewayHeaderAddrType

The address type in the H.248 message header.

cmedxGatewayDownServiceDelay

This object specifies the grace period before the media gateway link to be taken out of service. The value of 0 means to take the media gateway link out of service forcefully without any delay. The value of -1 means not to take the media gateway link out ...

cmedxGatewayActiveMgcAddress

The address of the currently active MGC in this media gateway link.

cmedxGatewayActiveMgcDomain

The domain name of the currently active MGC in this media gateway link.

cmedxGatewayActiveMgcPortNum

The transport layer port number of the currently active MGC in this media gateway link.

cmedxGatewayStateChangeReason

This object indicates the reason for the operational state change (cmedGatewayOperStatus) in the media gateway link. mgcDirected (1) - The state change is directed from MGC. mgDirected (2) - The state change is directed from MG. mgcNotReachable (3) - The ...

cmedxGatewayStateChangeMethod

This object indicates the method for the operational state change (cmedGatewayOperStatus) in the media gateway link. other (1) - None of the methods listed below. graceful (2) - The state change to 'down(2)' is by the way of graceful out of service. fo ...

cmedxGatewayAdminAction

This object specifies the action that users used to change the service state of the media gateway link. This object can be modified while the entry is active. up (1) - Bring the service state up. The value of cmedxGatewayDownServiceDelay will b ...

cmedxGatewayMaxCommandMsgSize

This object specifies the maximum message size on this gateway link for a H248 transaction containing the media gateway initiated commands. For example, this object would limit the size of a H248 transaction containing the media gateway initiated ServiceC ...

cmedxGatewayMaxReplyMsgSize

This object specifies the maximum message size on this gateway link for a H248 transaction containing the media gateway reply messages to MGC. For example, this object would limit the size of a H248 transaction containing the media gateway reply message t ...

cmedxGatewaySctpAssocId

This object specifies the SCTP association ID associated with the H.248 association. This SCTP association ID is the index (cSctpAssocId) of the entry in cSctpAssocTable. If the SCTP ID value is 0, it indicates no SCTP association.

cmedxGatewaySrvChgProfile

This object specifies the profile name used in the profile parameter of ServiceChange message to specify the attributes and behaviors of the media gateway.

cmedxGatewaySrvChgProfileVer

This object specifies the version of the profile indicated in cmedxGatewaySrvChgProfile.

cmedxGatewayMsgTokenType

This object specifies the H248 message is in short formatted PDU or long formatted PDU.

cmedxGatewayMgProvisionRspTime

This object specifies the time within which to expect a Pending Response if a transaction cannot be completed in the media gateway and in the MGCs of the media gateway link. The value of this object should be greater than the value of cmedxGatewayMgExecTi ...

cmedxGatewayMgcProvisionRspTime

This object specifies the time within which to expect a Pending Response from the MGC if a transaction cannot be completed. The value of this object should be greater than the value of cmedxGatewayMgcExecTime.

cmedxGatewayMgOrigPendLimit

This object specifies the number of TransactionPendings that MG will send. Once this limit is exceeded, MG will send a TransactionReply with Error 506.

cmedxGatewayMgcOrigPendLimit

This object specifies the number of TransactionPendings that MG expects to receive. Once this limit is exceeded, MG will assume a TransactionReply with Error 506.

cmedxGatewayDomainName

This object specifies the unique domain name to be used for each gateway link. This object is relevant only if cmedxGatewayHeaderAddrType is set to 'dns'. The agent won't allow any attempt to set this value for other address types. This domain name is exp ...

cmedxGatewayCmbDnAndPortInMID

This object specifies whether the MID should be a combination of the transport port number and the domain name represented by cmedGatewayPort and cmedxGatewayDomainName respectively, when cmedxGatewayHeaderAddrType is 'dns' . A value of 'true' indicates t ...

cmedxTerminationTypeTable

This table defines the attributes of a termination type for a group of ephemeral terminations.

cmedxTerminationTypeEntry

Each entry represents one termination type for a group of ephemeral terminations in H.248. When creating an entry, the object cmedxTermType have to be provided.

cmedxTermTypeId

An unique identification number that is assigned to the termination type by the manager

cmedxTermType

This object specifies the type of a group of ephemeral terminations. unknown (1) - none of the types listed below. scn (2) - SCN/DS terminations pdnRtp (3) - PDN terminations of RTP type. pdnAtmAal1 (4) - PDN terminations of ATM type with AA ...

cmedxTermTypeProfileId

The property profile identifier with which the terminations within this termination type will be associated.

cmedxTermTypePkgIds

The H.248 packages applied to this termination type.

cmedxTermTypeRowStatus

This object is used to create new rows, modify existing rows and to delete existing rows.

cmedxProfileTable

This table contains a list of the configurable properties in the H.248 profile supported in a media gateway. A property profile can be applied to a termination, a group of termination, or a termination type.

cmedxProfileEntry

Each entry represents all possible configurable properties supported by Cisco media gateway in an H.248 profile.

cmedxProfileIndex

This object uniquely identifies the H.248 profile.

cmedxProfilePlayCpToneInterDur

This object specifies the duration for playing a list of call progressing tones between two call progressing signals. The value of 0 indicates there is no wait between two call progressing signals.

cmedxProfileDtmfDigitOnDur

This object specifies the duration of the active DTMF digit during DTMF playout from the gateway. A complete DTMF digit is characterized by DTMF on with duration specified by this object followed by a pause (signal off) duration specified by the object cm ...

cmedxProfileDtmfPauseDur

This object specifies the duration of the pause after an active DTMF digit during DTMF playout from the gateway. For playout of multiple DTMF digits, the sum of the digit-on and pause (signaling velocity) should not be shorter than the time specified in Q ...

cmedxProfileCot1Frequency

This object specifies the tone frequency to be transmit between gateways in the continuity test.

cmedxProfileCot2Frequency

This object specifies the tone frequency to be received between gateways in the continuity test.

cmedxProfileInitiateCotDur

This object specifies the duration for the continuity test tone to be played when the gateway initiates a COT. The value of 0 indicates that the tone will be played infinitely unless interrupted.

cmedxProfileRespCotMethod

This object specifies the method for responding to COT (Continuity Test Tone) when the gateway detects a the continuity test signal. loopback (1) - The gateway loops back the received continuity test signal. transponder (2) - The gateway responds with ...

cmedxProfileDetectLongCpToneDur

This object specifies the duration for detecting a long call progressing tone.

cmedxProfileDetectLongDigitDur

This object specifies the duration for detecting a long digit tone signal.

cmedxProfileEchoCancelEnabled

This object specifies whether or not the Echo Cancellation is enabled or not.

cmedxProfileEchoCancelTail

This object specifies the Echo Canceler coverage. This object is valid if the cmedxProfileEchoCancelEnabled object is 'true'. echoCanceller8ms - 8 ms echo canceler coverage. echoCanceller16ms - 16 ms echo canceler coverage. echoCanceller24ms - 24 ms ech ...

cmedxProfileInGainControl

This object contains the amount of gain inserted at the receiver side of the interface. The input gain settings only define a gain/loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desi ...

cmedxProfileOutAttnControl

This object contains the amount of attenuation inserted at the transmit side of the interface. The output attenuation settings only define a loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based o ...

cmedxProfileVoIpVadEnabled

This object specifies VAD (Voice Activity Detection) is enabled for the compression DSPs of this interface when the application is VoIP.

cmedxProfileVoIpVadTimer

This object specifies the hangover time for VAD in the VoIP application. Once the voice inactivity is detected, the media gateway waits for the duration of this value before activating silence suppression. This object is not applicable if cmedxProfileVoIp ...

cmedxProfileVoAal2VadTimer

This object specifies the hangover time for VAD in the VoATM over AAL2 application. Once the voice inactivity is detected, the media gateway waits for the duration of this value before activating silence suppression. This object is not applicable if cvapA ...

cmedxProfileAtmBearerType

This object specifies ATM bearer type. bearerSvc (1) - the ATM bearer type is SVC (Switched Virtual Circuit). bearerPvc (1) - the ATM bearer type is PVC (Permanent Virtual Circuit).

cmedxProfileAtmAalPartialFill

This object specifies the fill level of cells in case of AAL adaptation . The value of this object will be used if the MGC does not specify partial fill in the commands. ATM cell size is 53 bytes, 5 bytes for header, 48 bytes for data. If the data are not ...

cmedxProfileAtmAalType

This object specifies the adaptation layer of ATM. other (1) - None of the types listed below. aal1 (2) - ATM AAL1 adaptation layer aal1Sdt (3) - ATM AAL1 with SDT (Structured Data Transfer) aal1Udt (4) - ATM AAL1 with UDT (Unstructured Data Transfer ...

cmedxProfileSuppressBearerDigit

This object controls if the digits should be suppressed from voice media stream. When MGC has requested digits, if this object is set to 'true', the digits will be reported to MGC only, the digits will not be sent as regular voice or peer-to-peer packets ...

cmedxProfileRowStatus

When an entry is created, at least one of the objects in the entry has to be provided and the default value will be assigned to the rest of the objects.

cmedxProfileOriginatingCotTx

This object specifies the COT tone to be transmitted from originating gateway in the continuity test.

cmedxProfileOriginatingCotRx

This object specifies the COT tone to be received in originating gateway in the continuity test.

cmedxProfileTerminatingCotTx

This object specifies the COT tone to be transmitted from terminating gateway in the continuity test.

cmedxProfileTerminatingCotRx

This object specifies the COT tone to be received in terminating gateway in the continuity test.

cmedxProfileComfortNoiseGenerate

This object specifies the type of comfort noise generation: (1) none: No comfort noise generation applied (2) simple: Cisco Proprietary comfort noise generation (3) g711A2: ITU G.711 Appendix II compliant DEFVAL { simple } ::= { cmedxProfileEntry ...

cmedxCallRenotifInterval

This object specifies the interval of the congestion renotification from the media gateway to the MGC. In the event of congestion on the Media Gateway, gateway generates an event towards MGC. Using this message, MG requests percentage reduction in the rat ...

cmedxCRRNumOfLevel

This objects specifies the number of level corresponding to which a different call reduction rate notification is generated towards MGC. Each level has a different call reduction rate, the CRR information is stored on cmedxCallReduceLevelTabl. And The tab ...

cmedxCurrentCRR

This object indicates the current percentage reduction in the rate of calls that MGC is attempting towards MG. ::= { cmedxCallReduceControlEntry 4 } SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION This object indic ...

cmedxCrrNotifyEnabled

This object indicates the bit map of the H248 association index (cmedGatewayLinkId) in which the gateway congestion notification is enabled. The MSB (most significant bit) is the association index 1. A 1-bit indicates the gateway congestion notification i ...

cmedxCurrentCallState

This object indicates the state of the gateway in accepting the incoming new call. acceptCall - the incoming new call will be processed. dropCall - the incoming new call will be droped due to the resources congested.

cmedxCallReduceLevelTable

The table presents mapping between a level and corresponding call reduction rate.

cmedxCallReduceLevelEntry

The number of entry on this table is determined by the MIB object 'cmedxCRRNumOfLevel'.

cmedxCallReduceLevelNum

The index starts from 1, and the maximum index equals to 'cmedxCRRNumOfLevel'.

cmedxCallReduceRate

This object indicates call reduction rate (CRR) for a given call reduce rate level. The default value of this object is based on the formula: level 1: 100 other level: 100 - ((80/(nol - 1)) * (level - 1)) Here: nol : number of level(cmedxCRRNumOfLevel) l ...

cmedxOverloadControlTable

This table is used to configure the media gateway overload control parameters specified in H.248.11 package.

cmedxOverloadControlEntry

An entry in this table contains the overload control parameters of the media gateway.

cmedxOverloadControlEnabled

This object controls if the H.248 overload package (H.248.11) and its associated features should be enabled for the media gateway. If this object is set to 'false', then the following MIB objects and MIB table will be ignored: cmedxOverloadNotifyState cme ...

cmedxOverloadNotifyState

This object indicates the current gateway overload notification state. The value of 'true' means the gateway will notify MGC when the gateway is overloaded. The value of 'false' means the gateway won't notify MGC when the gateway is overloaded. This objec ...

cmedxOverloadNotifyEnabled

This object indicates the bit map of the H248 association index (cmedGatewayLinkId) in which the gateway overload notification is enabled. The MSB (most significant bit) is the association index 1. A 1-bit indicates the gateway overload notification is en ...

cmedxCodecNegotiationTable

This table contains configuration information for different type of CODEC negotiation of calls which include voice call over adaptation layer AAL1 and AAL5. If the value lclLcoRcd(5), lclRcdLco(6) of cvapCodecNegotiationOption is used as CODEC negotiation ...

cmedxCodecNegotiationEntry

An entry represents a CODEC rate supported for VoIP or VoATM with AAL1 or AAL5 application in the media gateway. A list of entries for all CODEC types supported in the media gateway are created by the agent when a cmedxProfileEntry is created.

cmedxCodecNegotiationCodec

This object specifies the CODEC to be used in this profile.

cmedxCodecNegotiationPreference

This object specified the preference configured by the user for each CODEC. Lower the number, higher the preference of the CODEC. If this object is set to 0, the corresponding CODEC will not be used in coded negotiation procedure. Initially, if the value ...

cmedxGatewayStatsTable

This table is extended from cmedGatewayStatsTable which contains additional control protocol related statistics of the media gateway link.

cmedxGatewayStatsEntry

Entry holding statistics about a group of media Gateway/signaling link pair

cmedxGatewayLastEvent

The event code of the last event occurred on the link.

cmedxCommandStatsTable

This table provides the H.248 Command related statistics for the media gateway link. The H.248 protocol provides commands for manipulating the logical entities of the protocol connection model, Contexts and Terminations. For example, Commands exist to add ...

cmedxCommandStatsEntry

The system creates one entry for each media gateway link when it is created.

cmedxCmdNumAddFails

Total number of cumulative ADD commands failed in the media gateway link.

cmedxCmdNumAddSucceeds

Total number of cumulative ADD command succeeded in the media gateway link.

cmedxCmdNumSubtractFails

Total number of cumulative SUBTRACT commands failed in the media gateway link.

cmedxCmdNumSubtractSucceeds

Total number of cumulative SUBTRACT commands succeeded in the media gateway link.

cmedxCmdNumMoveFails

Total number of cumulative MOVE commands failed in the media gateway link.

cmedxCmdNumMoveSucceeds

Total number of cumulative MOVE commands succeeded in the media gateway link.

cmedxCmdNumModifyFails

Total number of cumulative MODIFY commands failed in the media gateway link.

cmedxCmdNumModifySucceeds

Total number of cumulative MODIFY commands succeeded in the media gateway link.

cmedxCmdNumAuditValFails

Total number of cumulative AUDIT VALUE commands failed in the media gateway link.

cmedxCmdNumAuditValSucceeds

Total number of cumulative AUDIT VALUE commands succeeded in the media gateway link.

cmedxCmdNumAuditCapFails

Total number of cumulative AUDIT CAPABILITY commands failed in the media gateway link.

cmedxCmdNumAuditCapSucceeds

Total number of cumulative AUDIT CAPABILITY commands succeeded in the media gateway link.

cmedxCmdNumNotifyFails

Total number of cumulative NOTIFY commands failed to respond from MGC.

cmedxCmdNumNotifySucceeds

Total number of cumulative NOTIFY commands successfully responded from the MGC.

cmedxCmdNumSrvChgFromMgcFails

Total number of cumulative ServiceChange commands from MGC to MG failed in the media gateway link.

cmedxCmdNumSrvChgFromMgcSucceeds

Total number of cumulative ServiceChange commands from MGC to MG succeeded in the media gateway link.

cmedxCmdNumSrvChgFromMgFails

Total number of cumulative ServiceChange commands from MG to MGC failed in MGC.

cmedxCmdNumSrvChgFromMgSucceeds

Total number of cumulative ServiceChange commands from MG to MGC succeeded in MGC.

cmedxCmdTotalFails

Total number of commands failed in the media gateway link. ::= { cmedxCommandStatsEntry 19 } SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION Total number of commands succeeded in the media gateway link. ::= { cmedxC ...

cmedxCmdNumNotifyPendings

Total number of cumulative NOTIFY commands remain pending in response from MGC.

cmedxCmdNumSrvChgFromMgcPendings

Total number of cumulative ServiceChange commands from MGC to MG remain pending in the media gateway link.

cmedxCmdNumSrvChgFromMgPendings

Total number of cumulative ServiceChange commands from MG to MGC remain pending in MGC.

cmedxCmdTotalPendings

Total number of commands remain pending in the media gateway link. ::= { cmedxCommandStatsEntry 31 } -- ******************************************************************** -- cmedxContextStatsTable -- ***************************************************** ...

cmedxContextStatsEntry

The system creates one entry for each media gateway link when it is created.

cmedxCntxNumActiveContexts

The current number of active contexts in the media gateway link.

cmedxCntxPeakNumActiveContexts

Peak number of active contexts in the media gateway link.

cmedxCntxNumContextAllocated

Total number of contexts has been allocated in the media gateway link.

cmedxCntxNumContextFreed

Total number of contexts has been freed in the media gateway link.

cmedxCntxShortestContextLife

The shortest life span for the contexts in the media gateway link.

cmedxCntxAverageContextLife

The average life span for the contexts in the media gateway link.

cmedxCntxLongestContextLife

The longest life span for the contexts in the media gateway link.

cmedxCntxNumCntxMoreThan2Terms

The number of contexts having more than 2 terminations in the media gateway link.

cmedxPhysicalTermStatsTable

This table contains statistics related to physical terminations in a media gateway.

cmedxPhysicalTermStatsEntry

Each entry contains the statistics for a physical termination in the media gateway.

cmedxPhyTermStatsNumAdds

Number of total ADD commands on this physical termination.

cmedxPhyTermStatsNumFailures

Number of total command failures on this physical termination.

cmedxPhyTermStatsOosFromMgcs

Number of total out of service initiated from MGC on this physical termination.

cmedxPhyTermStatsOosFromOams

Number of total out of service initiated from OAM (Operation Administration Management, either MG or NMS) on this physical termination.

cmedxEphemeralTermStatsTable

This table contains statistics related to ephemeral terminations.

cmedxEphemeralTermStatsEntry

Each entry contains the statistics of all ephemeral terminations for the termination type.

cmedxEphTermStatsType

This object specifies the statistics of the termination type to be retrieved. all (1) - Statistics for all ephemeral termination types. scn (2) - Statistics for SCN/DS terminations pdnRtp (3) - Statistics for PDN terminations of RTP type ...

cmedxEphTermStatsNumAdds

Number of total ADD commands has been initiated on this termination type.

cmedxEphTermStatsNumFailures

Number of total command failures on this termination type.

cmedxCommandProcStatsTable

This table provides the statistics related to H.248 command processing on a media gateway link. ::= { cmedxStats 6 } SYNTAX CmedxCommandProcStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION The information in each entr ...

cmedxCmdMaxInProgCmds

The maximum number of in-progress commands on a media gateway link. ::= { cmedxCommandProcStatsEntry 26 } SYNTAX Unsigned32 UNITS "seconds The elapsed time (in seconds) from the last periodic reset. All (non-accumulator) statistic objec ...

cmedxOverloadStatsEntry

Each entry contains the statistics of gateway overload control.

cmedxOverloadEnterCounts

The number of times that the gateway enters the overload condition because of any of CAC monitoring resources has exceeded the medium threshold specified by the value of ccacSysRpMedThreshold since the last counter reset.

cmedxOverloadExitCounts

The number of times that the gateway exits the overload condition when all of CAC monitoring resources have fallen below the low threshold specified by the value of ccacSysRpLowThreshold since the last counter reset.

cmedxOverloadCurrentState

This object indicates the current overload state of the gateway. normal - In normal condition. overload - In overload condition.

cmedxOverloadLastResetTime

This object contains the value of sysUpTime when the last counter reset occurred by setting cmedxOverloadCountersClear to 'true'. If no counter reset has occurred since the last time the media gateway reboot, this object will contain value of zero.

cmedxOverloadCountersClear

When this object is to set value of true(1), all statistics counters in the table cmedxOverloadStatsTable will be reset to zero. Setting this object to a value of false(2) has no implication. This object will always return 'false' upon any SNMP get operat ...

cmedxOverloadResourceStatsTable

This table contains the statistics of the resource utilization when the gateway enters overload condition.

cmedxOverloadResourceStatsEntry

Each entry contains the utilization statistics of the resource when the gateway is overloaded.

cmedxOverloadRsResourceIndex

This object uniquely identifies the utilization of the resource is monitored for the gateway overload. The value of 0 is to sum the individual statistical counter for all the monitored resources.

cmedxOverloadRsHighCounts

The accumulated number of times that the utilization of the resource is above the high threshold specified by ccacSysRpHighThreshold when the gateway enters the overload condition since the last counter reset.

cmedxOverloadRsMedCounts

The accumulated number of times that the utilization of the resource is above the medium threshold specified by ccacSysRpMedThreshold when the gateway enters the overload condition since the last counter reset.

cmedxOverloadRsLowCounts

The accumulated number of times that the utilization of the resource is above the low threshold specified by ccacSysRpLowThreshold when the gateway enters the overload condition since the last counter reset.

cmedxOverloadContributorCounts

The accumulated number of times the CAC monitoring resource causes the gateway entering the overload condition since the last counter reset.

cmedxOverloadRsLastResetTime

This object contains the value of sysUpTime when the last counter reset occurred by setting cmedxOverloadRsCountersClear to 'true'. If no counter reset has occurred since the last time the media gateway reboot, this object will contain value of zero.

cmedxOverloadRsCountersClear

When this object is to set value of true(1), all statistics counters in the table cmedxOverloadResourceStatsTable will be reset to zero. Setting this object to a value of false(2) has no implication. This object will always return 'false' upon any SNMP ge ...

cmedxEphemeralTermStatsInfoTable

This table contains statistics information related to ephemeral terminations.

cmedxEphemeralTermStatsInfoEntry

Each entry contains the ephemeral termination statistics inforamtion for a specific level. INDEX { cmedxEphTermInfoStatsIndex } ::= { cmedxEphemeralTermStatsInfoTable 1 } CmedxEphemeralTermStatsInfoEntry ::= SEQUENCE { cmedxEphTermInfoStatsIndex ...

cmedxConfigGroup

This group contains of all the configuration extended information for a media gateway.

cmedxStatsGroup

This group contains of all the statistics information for the statistics in a media gateway.

cmedxCallReduceRateGroup

This group contains objects used to manage and/or monitor the rate at which call attempts are made by Media gateway controller on this Media Gateway.

cmedxCodecNegotiationGroup

This group contains objects used for CODEC negotiation between MG and MGC.

cmedxConfigExtGroup

This group contains of the objects related to Megaco message size provisioning and BellCore standard COT a media gateway.

cmedxServiceStateGroup

This group contains of the objects to change the service state of a media gateway.

cmedxConfigGroupRev1

This group contains of all the configuration extended information for a media gateway.

cmedxCallReduceRateNotifyGroup

This group contains objects used for H.248.10 congestion control notification.

cmedxOverloadControlGroup

This group contains objects used for H.248.11 overload control package.

cmedxOverloadStatsGroup

This group contains objects used for the statistics of H.248.11 overload control.

cmedxStatsExtGroup

This group contains objects related to the extended statistics of H.248.

cmedxEphemeralTermStatsGroup

This group contains objects related to ephemeral termination statistics of H.248.

cmedxConfigGroupRev2

This group contains of all the configuration extended information for a media gateway.

cmedxStatsGroupRev1

This group contains of all the statistics information for the statistics in a media gateway.

cmedxConfigDomainInfoGroup

This group specifies the domain name and port configuration for a media gateway.