CISCO-MGX82XX-DSX1-MIB Download

dsx1CnfGrpTable

The DS1/E1 Configuration table. The table size is given by the value of lineNumofValidEntries ::= { dsx1CnfGrp 1 } SYNTAX Dsx1CnfGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry in the DS1 Configuration table.

lineNum

This object is the identifier of a DS1/E1 Interface on a managed device. If there is an ifEntry that is directly associated with this and only this DS1/E1 interface, it should have the same value as ifIndex. Otherwise, number the ds1LineIndices with an u ...

lineConnectorType

This variable indicates the connector as well as the backcard type. 1 = T1; 2 = E1. This field is set to unused(4) for FRSM-VHS cards.

lineEnable

This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify In FRSM-2CT3, if the DS3 line is enabled, then the DS1 channels for that line will all be automatically enabled. No independent enable/disable is allowed for each of the ...

lineType

This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The ...

lineCoding

This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1JBZS(1): refers the Jammed Bit Zero suppression in which the AT&T specification of at least one pulse eve ...

lineLength

This is not a standard RFC 1407 DS1 variable, it is specific to BASIS implementation. It specifies the line length: 1 - 0 to 110 ft (T1 line only) 2 - 110 to 220 ft (T1 line only) 3 - 220 to 330 ft (T1 line only) 4 - 330 to 440 ft (T1 line only) 5 - 440 t ...

lineLoopbackCommand

This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback state that the interface does not support. The values mean: dsx1NoLoop Not in ...

lineLoopbackCodeDetection

Enable detection of line Loopback Codes DEFVAL {codeDetectDisabled} ::= { dsx1CnfGrpEntry 11 } SYNTAX INTEGER { disable (1), enable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION This variable enables Bit Error Rate Testing(BERT).

lineBERTPattern

This variable determines BERT pattern to transmit DEFVAL { allZeros } ::= { dsx1CnfGrpEntry 13 } SYNTAX INTEGER { failed(1), passed(2) } MAX-ACCESS read-write STATUS current DESCRIPTION This shows the result of the BERT.

bERTResultClrButton

This clears the result of the BERT.

lineNumofValidEntries

The number of DS1 configuration entries (regardless of their current configuration) in the dsx1CnfGrpTable.

dsx1CntGrpTable

The DS1 Counter table. This table contains statistics since the system was up or last re-initialization.

dsx1CntGrpEntry

An entry in the DS1 counter table.

cntLineNum

This object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable.

rcvLOSCount

The number of times the Loss of Signal was detected with or without integrating to LOS alarm.

rcvOOFCount

The number of times the Out of Frame was detected with or without integrating to OOF alarm.

rcvRAICount

The number of times Yellow Alarms was detected with or without integrating to RAI alarm.

rcvFECount

The number of Framing Pattern Errors encountered by a DS1 interface.

counterClearButton

This variable is used to clear all the counters.

dsx1AlmCnfGrpTable

The DS1 interface alarm configuration table. ::= { dsx1AlmCnfGrp 1 } SYNTAX Dsx1AlmCnfGrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION An entry in the DS1 Alarm Configuration table.

almCnfLineNum

This object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable.

redSeverity

This variable is used to setup the severity of RED alarm. So when RED alarm is detected by the card, an alarm with appropriate severity status will be sent.

rAISeverity

This variable is used to setup the severity of RAI alarm. So when LOS alarm is detected the card, an alarm with appropriate severity status will be sent.

nEAlarmUpCount

This parameter specifies the integration counter, the local alarms are LOS and LOF. Default value is 6 and update counter every 10 ms to reach the threshold set in threshold object. This is the up counter.

nEAlarmDownCount

This parameter specifies the integration counter, the Near-End alarms are LOS and LOF. Default value is 1 and update counter every 10 ms to reach 0. This is the down counter.

nEAlarmThreshold

The value set in this object determines the value to declare Near-End alarm. A count of 1500 gives 2.5 sec to declare LOS with an up count value of 6.

fEAlarmUpCount

This parameter specifies the integration counter, the Far-End alarms are AIS and YEL. Default value is 6 and update counter 10 ms to reach the threshold set in threshold object. This is the up counter.

fEAlarmDownCount

This parameter specifies the integration counter, the Far-End alarms are AIS and YEL. Default value is 1 and update counter every 10 ms to reach 0. This is the down counter.

fEAlarmThreshold

The value set in this object determines the value to declare Far-End alarm. A count of 1500 gives 2.5 secs to declare LOS with an up count value of 6.

statisticalAlarmSeverity

This variable is used to setup the severity of Statistical alarm. So when any statistical alarm is detected by the card, an alarm with appropriate severity status will be sent.

lCV15MinThreshold

Code Violation - is the occurrence of a received CRC-6 code that is not identical to the corresponding locally. calculated code. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be d ...

lCV24HrThreshold

Code Violation - is the occurence of a received CRC-6 code that is not identical to the corresponding locally. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The ...

lES15MinThreshold

Errored Second - is any second with at least one code violation. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

lES24HrThreshold

Errored Second - is any second with at least one code violation. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the ...

lSES15MinThreshold

Severely Errored Second - is any second with 15 or more code violations. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

lSES24HrThreshold

Severely Errored Second - is any second with 15 or more code violations. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes ...

cRC15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

cRC24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

cRCES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

cRCES24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

cRCSES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

cRCSES24HrThreshold

The value set in this object determines the value when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

sEFS15MinThreshold

Severely Errored Framing Second - is a count of one-second intervals containing one or more SEF events. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

sEFS24HrThreshold

Severely Errored Framing Second - is a count of one-second intervals containing one or more SEF events. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The thresh ...

aISS15MinThreshold

Alarm Indication Signal Second - is a count of one-second intervals containing one or more incoming AIS. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

aISS24HrThreshold

Alarm Indication Signal Second - is a count of one-second intervals containing one or more incoming AIS. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The thres ...

uAS15MinThreshold

Unavailable Second - is a count of seconds during which the DS1 Layer service is unavailable. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

uAS24HrThreshold

Unavailable Second - is a count of seconds during which the DS1 Layer service is unavailable. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is che ...

dsx1AlmGrpTable

The DS1 interface alarm configuration table.

dsx1AlmGrpEntry

An entry in the DS1 Alarm table. Each entry represents the current, 15 minute and 24 Hour bucket intervals for different performance parameters.

almLineNum

This object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable.

lineAlarmState

This variable is a bitmap of the DSX1 Line Alarms. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 Receiving RAI 1 Transmitting RAI 2 Receiving ...

lineStatisticalAlarmState

This variable is a bitmap of the DSX1 Line Statistical Alarms. A value of zero indicates no alarms. Itemized below are the individual alarm bits: BitPosition Alarm ----------- ----- 0 LCV 15 minute threshold exceeded 1 LCV ...

lCVCurrent

This counter counts the number of Line code violations encountered by the interface.

lCV15MinBucket

The counter associated with the number of Line code violations in the last 15 minute period encountered by the interface.

lCV24HrBucket

The counter associated with the number of Line code violations in the last 24 hour period encountered by the interface.

lESCurrent

This counter counts the number of Line code violations Errored Seconds encountered by the interface.

lES15MinBucket

This counter counts the number of Line code violations Errored Seconds in the last 15 minutes encountered by the interface.

lES24HrBucket

This counter counts the number of Line code violations Errored Seconds in the last 24 hours encountered by the interface.

lSESCurrent

This counter counts the number of Line code violations Severely Errored Seconds encountered by the interface.

lSES15MinBucket

This counter counts the number of LCV Severely Errored Seconds in the last 15 minutes encountered by the interface.

lSES24HrBucket

This counter counts the number of LCV Severely Errored Seconds in the last 24 hours encountered by the interface.

cRCCurrent

This counter counts the number of P Bit code violations encountered by the interface.

cRC15MinBucket

This counter counts the number of P Bit code violations in the last 15 minutes encountered by the interface.

cRC24HrBucket

This counter counts the number of P Bit code violations in the last 24 hours encountered by the interface.

cRCESCurrent

This counter counts the number of PCV Errored Seconds encountered by the interface.

cRCES15MinBucket

This counter counts the number of PCV Errored Seconds in the last 15 minutes encountered by the interface.

cRCES24HrBucket

This counter counts the number of PCV Errored Seconds in the last 24 hours encountered by the interface.

cRCSESCurrent

This counter counts the number of P Bit code violations Severely Errored Seconds encountered by the interface.

cRCSES15MinBucket

This counter counts the number of PCV Severely Errored Seconds in the last 15 minutes encountered by the interface.

cRCSES24HrBucket

This counter counts the number of PCV Severely Errored Seconds in the last 24 hours encountered by the interface.

sEFSCurrent

This counter counts the number of Severely Errored Framing Seconds encountered by the interface.

sEFS15MinBucket

This counter counts the number of Severely Errored Framing Seconds in the last 15 minutes encountered by the interface.

sEFS24HrBucket

This counter counts the number of Severely Errored Framing Seconds in the last 24 hours encountered by the interface.

aISSCurrent

This counter counts the number of AIS Severely Errored Seconds encountered by the interface.

aISS15MinBucket

This counter counts the number of AIS Severely Errored Seconds in the last 15 minutes encountered by the interface.

aISS24HrBucket

This counter counts the number of AIS Severely Errored Seconds in the last 24 hours encountered by the interface.

uASCurrent

This counter counts the number of Unavailable Seconds encountered by the interface.

uAS15MinBucket

This counter counts the number of Unavailable Seconds in the last 15 minutes encountered by the interface.

uAS24HrBucket

This counter counts the number of Unavailable Seconds in the last 24 hours encountered by the interface.

percentEFS

This counter counts the %LCV Error Free Seconds.

alarmClrButton

This variable is used to clear all the alarms for the line. 1 = No action 2 = Clear alarm ::= { dsx1AlmGrpEntry 32 } -- conformance information cmDsx1MIBConformance OBJECT IDENTIFIER ::= { ciscoMgx82xxDsx1MIB 2 } cmDsx1MIBGroups OBJECT IDENTIFIER : ...

cmDsx1GeneralGroup

The collection of objects used for DS1/E1 interfaces.

cmDsx1ConfGroup

The collection of objects used for DS1/E1 interface configuration.

cmDsx1CountGroup

The collection of objects related to DS1/E1 statistics.

cmDsx1AlarmConfGroup

The collection of objects used for DS1/E1 Alarm threshold configuration.

cmDsx1AlarmGroup

The collection of objects used for DS1/E1 Alarm configuration.