CISCO-WAN-FR-PORT-MIB Download

frPortCnfPortGrpTable

This table is used for creating/configuring Frame Relay Logical(referred to as frame relay port)Ports. Relation with ifTable: The modules in which ifTable is implemented, the creation of frame relay port in this table will cause an entry to be created in ...

portNum

This is the frame relay(logical) port number. For Service Modules, supporting ifTable, this must be the ifIndex value of the frame relay port. The port number value supported depends upon the following for each Service Module: - type(Channelized, Unchanne ...

portLineNum

This object represents the physical line number on which the frame relay port need to be created. For Service Modules, supporting ifTable, this must be the ifIndex value of the physical line or logical interface. The ifIndex entries in ifTable applicable ...

portRowStatus

The value of this object is used for creating modifying or deleting frame relay ports. The possible values are : add(1) : Create frame relay port del(2) : Delete frame relay port mod(3) : Modify the frame relay port. This value is required to be set in So ...

portDs0ConfigBitMap

This respesents bit map of DS0s for a line/interface which are used to form this logical port. The Bit 0 represents DS0-1(First DS0 timeslot). This object is not applicable for unchannelized service modules. In case of unchannelized interfaces, this field ...

portDs0Speed

The value of this object is used for configuring the port speed(or data rate) of Ds0 in frame relay port. speed56k(1) : set to 56k speed64k(2) : set to 64k unUsed(3) : Not applicable. This field is not applicable for unchannelized interfaces/ports. In c ...

portFlagsBetweenFrames

Number of flags transmitted between FR frames For FRSM12 card: Only the values 1 to 8 are supported. The mapping is as follows: MIB object value No. of HDLC flags inserted 1 1 2 2 3 ...

portEqueueServiceRatio

Number of times queue 1 is serviced for every time queue 2 is serviced. The value 0 is supported only by FRSM-VHS. FRSM-VHS supports two different egress queue servicing algorithms depending on the Egress Qos Feature. if EgrQosFeature is ENABLED, Weighted ...

portSpeed

The value of this object contains the Configured speed of port.

portAdmin

The value of this object is used for changing the desired state of the port. up(1) : Up the port;Admin up down(2) : Down the port;Admin down For Service Modules, supporting ifTable, this is equivalent to 'ifAdminStatus' object. The write-only is not sup ...

portType

The value of this object identifies the network interface for this frame relay port. The Possible values are: frame-relay(1) : Frame Relay Service Port frFUNI (2) : Frame based UNI Port. when a frame arrives from the FUNI interface the 2 byte FUNI h ...

portSvcStatus

The value of this object is used for enabling/disabling the SVC operation on a frame relay port. For FRSM12 card: Not Supported

portSvcInUse

The value of this object is used for representing whether SVC is in use or not. For FRSM12 card: Not Supported ::= { frPortCnfPortGrpEntry 12 } SYNTAX INTEGER { port-based(1), card-based(2) } MAX-ACCESS read-only STATUS current DESCRIPTION The value of th ...

portSvcDlciHigh

The value of this object identifies the high end of reserved DLCI for SVC. For FRSM12 card: Not Supported.

portDeleteSvcs

The value of this object indicates that all the SVC connections on a given frame relay port has to be deleted. For FRSM12 card: Not Supported ::= { frPortCnfPortGrpEntry 18 } SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION The value of t ...

portBERTEnable

The value of this object enables/disables the Bit Error Rate Testing (BERT) on the frame relay port. For FRSM12 card: Not Supported DEFVAL { disable } ::= { frPortCnfPortGrpEntry 21 } SYNTAX INTEGER { disable (1), enable (2) } MAX-ACCESS read-write STATU ...

portHeaderLen

The value of this object identifies the Q.922 address field length and DLCI length for this UNI/NNI logical port. This object can not be modified if there are any frame relay connections that are configured on the port. This object is not applicable to MG ...

portFrameChkSumType

The value of this object identifies the CRC Length in the HDLC Packet. Applicable for FrameForwarding ports only. This object can not be modified if there are any frame relay connections that are configured on the port. This object is not applicable to MG ...

portOverSubEnable

The value of this object enables/disables the port to be over subscribed. This object is not applicable to MGX Release 1.x. DEFVAL { disable } ::= { frPortCnfPortGrpEntry 27 } -- PORT usage scalars -- These scalars are not used in FRSM-VHS and FRSM12 SYN ...

portsUsedLine2

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1, the most significant byte is invalid for DS1. This is for line 2.

portsUsedLine3

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 3.

portsUsedLine4

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 4.

portsUsedLine5

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 5.

portsUsedLine6

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 6.

portsUsedLine7

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 7.

portsUsedLine8

Each bits set represents a DS0 that is used by all the logical ports defined so far for that DS1. The most significant byte is invalid for DS1. This is for line 8.

portNextAvailable

This variable contains the next UNUSED logical port number. This number can be used in channel config table, the portNextAvailable gets updated if the number gets used to create a logical port. A '0' indicates that no more ports are available. For FRSM12 ...

portState

This variable indicates the state of the logical port ::= { frPortStateGrpEntry 2} SYNTAX Integer32 (0..'ffffff'h) MAX-ACCESS read-only STATUS current DESCRIPTION Bit 0 = 0 -> LMI O.K. or not enabled Bit 0 = 1 -> LMI failed Bit 1 = 0 -> CLLM O.K. or not e ...

portIngrPercentUtil

Percentage Utilization of the Port in the Ingress direction.

portEgrPercentUtil

Percentage Utilization of the Port in the Egress direction.

frPortCntPortGrpTable

The config table is for logical port interface there are upto 248 entries (for 8 E1s) or 192 (for 8 T1s). In FRSM-VHS, there is support for upto 256 entries. ::= { frPortCntPortGrp 1 } SYNTAX FrPortCntPortGrpEntry MAX-ACCESS not-accessible STATUS current ...

rcvPortFrames

The number of frames Received on the ingress.

rcvPortBytes

The number of bytes Received on the ingress.

rcvPortFramesDE

The number of frames with DE bit set received on the ingress.

rcvPortFramesFECN

The number of frames with FECN bit set received on the ingress.

rcvPortFramesBECN

The number of frames with BECN bit set received on the ingress.

rcvFramesDiscCRCError

The number of frames discarded on the ingress due to CRC error.

rcvFramesDiscAlignmentError

The number of frames discarded on the ingress due to Alignment error.

rcvFramesDiscIllegalLen

The number of frames discarded on the ingress due to illegal length.

rcvFramesDiscIllegalHeader

The number of frames discarded on the ingress due to illegal header.

rcvFramesAbort

The number of received frames aborted ::= { frPortCntPortGrpEntry 11 } SYNTAX Counter32 UNITS "Frames The number of frames received with an unknown DLCI.

rcvLastUnknownDLCI

The last unknown DLCI received.

rcvPortFramesTaggedFECN

The number of frames received that were tagged with FECN bit.

rcvPortFramesTaggedBECN

The number of frames received that were tagged with BECN bit.

rcvPortFramesTaggedDE

The number of frames received that were tagged with DE bit.

rcvPortFramesDiscXceedDEThresh

The number of frames discarded on the ingress due to exceeded DE Threshold.

rcvPortKbpsAIR

Received Average Information Rate in KBPS.

rcvBufNotAvailable

The number of times the receiver is turned off ::= { frPortCntPortGrpEntry 19 } SYNTAX Counter32 UNITS "Frames The number of frames transmitted.

xmtPortBytes

The number of bytes transmitted.

xmtPortFramesFECN

The number of frames transmitted with FECN bit already set.

xmtPortFramesBECN

The number of frames transmitted with BECN bit already set.

xmtPortFramesDiscXceedQDepth

The number of frames discarded on the egress due to exceeded queue depth For FRSM12 Card: Not Supported ::= { frPortCntPortGrpEntry 24 } SYNTAX Counter32 UNITS "Bytes The number of bytes discarded on the egress due to exceeded queue depth For FRS ...

xmtPortKbpsAIR

Transmit Average Information Rate in KBPS.

xmtBufNotAvailable

The number of times the transmitter is turned off For FRSM12 Card: Not Supported ::= { frPortCntPortGrpEntry 31 } SYNTAX INTEGER { noaction (1), clear (2) } MAX-ACCESS read-write STATUS current DESCRIPTION The value of this object is used for clearing ...

rcvFramesDiscNoChan

The number of frames received when no channel is setup.

rcvFramesDiscOverrun

The number of frames discarded in Ingress direction due to FIFO overrun in HDLC Controller. This object is not applicable to MGX Release 1.x ::= { frPortCntPortGrpEntry 34 } SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION Number o ...

frPortsUsedLineGrpEntry

An entry for each DS1 interface.

frPortsUsedLineIndex

This object uniquely identifies the DS1 interface.

frPortsUsedLine

The value of this object provides the information on DS0 time slots used by the DS1 identified by 'frPortsUsedLineIndex' object. A bit set represents a DS0 that is used by all the logical ports defined so far for DS1 interface. The most significant byte i ...

frPortServiceQueGrpTable

The config table is for logical port interface. In FRSM-VHS, there are 256 entries for FRSM-2CT3 card and 2 entries for FRSM-T3/E3/HS2/T3B/E3B/HS2B-HSSI cards and 8 entries for FRSM-HS2B-12IN1. The table is supported only in FRSM-VHS when the object egrQo ...

frServPortNum

This is the frame relay port number. The value of this object must match with the value of object 'portNum' in frPortCnfPortGrpTable.

portServiceQueueNo

This identifies the Q depending on the Service Type 1 High Priority Queue 2 rt VBR Queue 3 nrt VBR and ABR Queue 4 UBR Queue queue5(5) to queue8(8) are reserved for future use There are 8 queues but only four are being used as of now. ::= { frPortServiceQ ...

portEgresECNThresh

ECN threshold for the frame relay port. If the total queue depth of all connections mapped to this port queue exceeds this threshold, then the appropriate ECN bit (FECN in the downstream direction and BECN in the upstream direction) get set.

portEgresDEThresh

DE threshold for the frame relay port. If the total queue depth of all connections mapped to this port queue exceeds this threshold, and the DE bit is set in the incoming frame, then the frame gets dropped.

portQBwInc

Denotes the bandwidth increment for this port queue. The bandwidth increment is the percentage of the port bandwidth used by all connections mapped to a particular queue scaled by the value 16384.

portBytesDiscXceedQueFull

Counter maintained for the no of bytes discarded due to port queue depth exceeded.

portBytesDiscXceedDEThresh

Counter maintained for the no of bytes discarded due to DE threshold exceeded.

ciscoWanFrPortConfGroup

The collection of objects which are used to represent Frame Relay Port information.

ciscoWanFrPortSvcGroup

The collection of objects which are used to represent SVC characteristics of a Frame Relay Port.

ciscoWanFrPortDs0InDs1Group

The objects representing the DS0(in DS1) that are used by the frame relay logical ports.

ciscoWanFrPortStateGroup

The collection of objects related to state information of Frame Relay Ports.

ciscoWanFrPortStatsGroup

The collection of objects related to statistics information of frame relay ports.

ciscoWanFrPortServiceQueueGroup

The collection of objects related to service queue on frame relay ports.

ciscoWanFrPortsUsedGroup

The collection of objects related to information on DS0 time slots used in each DS1 line.