CISCO-WAN-SRM-BERT-MIB Download

bertControl

This object controls all the SET operations on this MIB group. acquireBert : Acquire BERT resources. cnfBert : Configure the required BERT test. startBert : The configured test has to be started. modBert : Modify parameters for the ongoing B ...

bertResourceStatus

All of bert resources can be used by only one user at a time. This gives the status of the resources.

bertOwner

This refers to the user who owns the BERT resources. If the user is a CLI user, then this is username. If it is SNMP Manager(For example Cisco Wan Manager), then this would be the IP address. For example, this value can be, 192.9.209.157 within quotes.

bertUserId

This identifies the user who wants to do a SET operation on this group. This will be compared against bertOwner and access will be given only if it matches. Hence, for every SET request, this object should have a valid value. If the user is a CLI user, th ...

bertStatus

This variable provides the status of BERT in the shelf.

bertSlotNumber

specifies the physical slot number of the Service Module which is to run BERT For MGX 8220, the range is 5-14. For MGX 8850, the range is 1-6, 9-14, 17-22, 25-30. Required for bert operations.

bertTestMedium

specifies whether the bert is to test a port or an entire T1/E1 line. No default value for this, it has to be set if bert is configured.

bertPort

specifies the port number for BERT.

bertLine

specifies the line number for BERT. If the test medium is port, this represents the line to which the port belongs.

bertMode

specifies the mode, the BERT module is to be configured for.

bertDeviceToLoop

This shows the type of the end device and the type of the loopback used (latching/nonlatching/polynomial).

bertDS0DPIterationCount

The Iteration Register needs to be programmed in SRM when DSO drop loop option is selected in bertDeviceToLoop. The value to be programmed there is minus one of this object value, since the register is 0 based. DSP-OP devices can be cross connected in th ...

bertPattern

This variable determines BERT pattern to be transmitted.

bertLoopback

specifies the type of loopback to be (d)established.

bertLoopbackOperation

specifies the operation of loopback (up or down).

bertDS0Speed

represents the ds0 speed of the test running.

bertTimeSlots

represents the number of ds0s in the test medium chosen.

bertStartTime

The syntax is hh:mm:ss The time zone is as configured in the shelf.

bertStartDate

On MGX 8220, the syntax is mm/dd/yy On MGX 8850, the syntax is mm/dd/yyyy.

bertBitCount

This shows the number of bits transmitted.

bertBitErrorCount

This shows the number of bits received in error.

bertErrorInjectCount

This shows the number of times error was injected.

bertCleanupAction

When the BERT has to be stopped or aborted (due to card state changes), this object would give the exact action to take. The bert related changes to the shelf, then, can be cleaned up. When its value is a Loopdown, it implies smCleanup plus the correspon ...

bertAbortReason

when the BERT is aborted, this object would give the reason for that.

bertDDSSeekResultsTableFirstIndex

Denotes the index of the oldest entry in the table. A value of zero means that there are no entries in the table.

bertDDSSeekResultsTableLastIndex

Denotes the index of the latest entry in the table. A value of zero means that there are no entries in the table.

bertDDSSeekResultsTable

This table contains all available DDS patterns detected and latched by an interaface(lines,ports etc) configured to detect DDS patterns.

bertDDSSeekResultsTableEntry

An entry in the detected DDS codes table.

bertDDSSeekResultsTableIndex

Denotes the serial number of the entry in the table.

bertDDSCode

Denotes the type of DDS code detected.

bertSupportedTestsTable

A list of supported tests for a given SM.

bertSupportedTestsTableEntry

A general supported tests entry.

bertSupportedTestsTableIndex

This index is the physical slot number of the Service Module whose entry it represents in the table. For MGX 8220, the range is 5-14. For MGX 8850, the range is 1-6, 9-14, 17-22, 25-30.

bertSupportFlag

'yes' if the table entry correctly represents the supported tests for the SM on the corresponding slot. 'no' if no tests at all are supported.

bertTestMediumMask

Every test medium is represented by a bit of mask. Bits 0-1 are valid in this integer. The meaning of the mask can be understood from the example below: -------------------------- TestMedium | SM | support -------------------------- port | 1 li ...

bertModeMask

Every mode is represented by 2 bits of mask. Bits 0-5 are valid in this integer. The meaning of the mask can be understood from the example below: ----------------------------------------------------------- Mode | SM support | Test Medium: | ...

bertDeviceToLoopMask

Every class of devices to loop is represented by 6 bits of mask. Bits 0-29 are valid in this integer. The meaning of the mask can be understood from the example below: ----------------------------------------------------------- | | | Tes ...

bertPatternMask

Every class of patterns is represented by 2 bits of mask. Bits 0-3 are valid in this integer. The meaning of the mask can be understood from the example below: ---------------------------------------------- Class of | SM | Non latching patter ...

bertLoopbackMask

Every loopback is represented by 2 bits of mask. Bits 0-5 are valid in this integer. The meaning of the mask can be understood from the example below: ---------------------------------------------- Loopback | SM | Test Medium | support | ...

bertCardT1E1Type

Specifies whether a t1 or e1 card.

ciscoWanSrmBertConfGroup

The collection of objects which are used for configuring/running BERT on Service modules using SRM module.

ciscoWanSrmBertTestResultsGroup

The collection of objects which are used for finding the results of running BERT tests.

ciscoWanSrmBertDDSResultsGroup

The collection of objects which are used for finding the results of running BERT tests using DDS pattern.