CROUTE-MIB Download

ipGlobalsBOOTPRelayStatus

Whenever to activate the BOOTP Relay protocol on the device. enable - set by the user, means activate the BOOTP Relay protocol over the defined VLANs. disable - set by the user, means don't active the BOOTP Relay protocol. backup - set by the user, means ...

ipGlobalsICMPErrMsgEnable

Whenever to send ICMP messages such as Destination Unreachable, etc.

ipGlobalsARPInactiveTimeout

Time-out required to remove inactive ARP entries. The value is in seconds. The default value is 4 hours

ipInterfaceTable

This table is an extention of MIB II IpAddrTable, and is used to add/delete entries to/from that table. In addition it contains private objects.

ipInterfaceEntry

The information concerning one of this entity's IP interfaces. An IP interface is a logical connection to a certain IP net/subnet.

ipInterfaceAddr

The IP address to which this entry's addressing information pertains.

ipInterfaceNetMask

The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.

ipInterfaceLowerIfAlias

This object is an 'alias' name for the lower-layer interface on top of which this IP interface is defined. The alias is specified by the network manager, and provides a non-volatile 'handle' for the lower-layer interface. The semantics of the object are s ...

ipInterfaceType

The logical type of the interface. The default depends on the physical type. For example Ethernet and Token-Ring LANs are of type broadcast

ipInterfaceForwardIpBroadcast

Whether the router forwards IP directed broadcasts that are to be transmitted as link-layer broadcast to an attached net or subnet.

ipInterfaceBroadcastAddr

The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value wi ...

ipInterfaceProxyArp

When proxy ARP is enabled, the router responds to ARP requests received on one link-layer interface for an IP-address that is reachable via another link-layer interface. The response provides the router's own MAC address.

ipInterfaceStatus

For adding and deleting IP interfaces. Deleting this row means deleting the corresponding entry in IpAddrTable (MIB II). Deleting an IP interface also causes deletion of all static routes defined on this IP interface, as well as protocol interfaces (e.g. ...

ipInterfaceMainRouterAddr

The IP address of the main router backed up on this interface.

ipInterfaceARPServerStatus

Whenever to activate the ARP Server mechanism on this interface. enable - set by the user, means activate the ARP Server mechanism over this IP interface. disable - set by the user, means don't active the ARP Server mechanism over this IP interface.

ipInterfaceName

The name of this interface for compatibility with cli.

ipInterfaceNetbiosRebroadcast

inbound - netbios received from the interface are rebarodcasted, outbound - netbios are rebraodcasted to this interface, both - netbios are rebroadacsted both from and to this interface, disable - netbios is not rebraodcasted neither from nor to this inte ...

ipInterfaceIcmpRedirects

enable - enable the sending of redirect messages if the router is forced to re-send a packet through the same interface on which it was received. disable - disable the sending of redirect messages on this interface.

ripGlobalsRIPEnable

Whenever to activate the RIP protocol on the device. disable means don't activate RIP over all the IP interfaces enable means that the status of each interface is relevant

ripGlobalsLeakOSPFIntoRIP

Whenever to leak (redistribute) routes learned from OSPF protocol into the domain of the RIP protocol.

ripGlobalsLeakStaticIntoRIP

Whenever to leak (redistribute) routes learned from Static Route into the domain of the RIP protocol.

ripInterfaceTable

This table is an extention of rip2IfConfTable, and is used to add/delete objects entries to/from that table.

ripInterfaceEntry

The information concerning one of this entity's IP interfaces. An IP interface is a logical connection to a certain IP net/subnet.

ripInterfaceAddr

The IP address to which this entry's addressing information pertains.

ripInterfaceMetric

This variable indicates the number of hops that is to be assign to that interface.

ripInterfaceSplitHorizon

Whether to activate Poison Reverse algorithm, Split Horizon or none of them, on this interface

ripInterfaceAcceptDefaultRoute

Whether to accept the default route from receive RIP message.

ripInterfaceSendDefaultRoute

Whether to send the default route in RIP message.

ripInterfaceState

The operational (current state) of the IP interface from RIP point of view. It depends on Global RIP status, IP interface status and rip interface STATUS. inactive - set by the device (status), the rip is not active on this interface. active - set by the ...

ripInterfaceSendMode

What the router sends on this interface. All - send the whole routing table according to the RIP version. DefaultOnly - send default route only. DoNotDend - don't send any RIP information on this interface.

ripInterfaceVersion

What RIP information the router sends on this interface.

ospfGlobalsLeakRIPIntoOSPF

Whenever to leak (redistribute) routes learned from RIP protocol into the domain of the OSPF protocol.

ospfGlobalsLeakStaticIntoOSPF

Whenever to leak (redistribute) routes learned from Static Route into the domain of the OSPF protocol.

ospfGlobalsLeakDirectIntoOSPF

Whenever to leak (redistribute) routes learned from Direct into the domain of the OSPF protocol.

relayTable

This table is an extention of vlConfTable, and is used to add/delete DHCP Servers to/from that table.

relayEntry

The information concerning one of this entity's VLAN interfaces. An VLAN interface is a virtual connection to a switch.

relayVlIndex

A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.

relayVlPrimaryServerAddr

The IP address of the primary server, to which the BOOTP/DHCP requests to be sent.

relayVlSeconderyServerAddr

The IP address of the secondary server, to which the BOOTP/DHCP requests to be sent.

relayVlStatus

For deleting an DHCP/BOOTP servers entry. The entry will be deleted upon deleting the corresponding VLAN

relayVlRelayAddr

The IP address of the Relay, i.e. the router's IP address to write in the relayed request (giaddr field in the Bootp packet). When there are multiple IP interfaces on the same VLAN such that the router has multiple IP addresses on the VLAN, the user can c ...

ipAccessControlEnable

Whenever to activate the IP ACCESS CONTROL statements on the device. disable means don't activate IP ACCESS CONTROL over all the IP statements enable means activate IP ACCESS CONTROL over all the IP statements

ipAccessControlTable

This table is used to add/delete access control statement to/from that table.

ipAccessControlEntry

The information concerning one of this entity's IP interfaces. An IP interface is a logical connection to a certain IP net/subnet.

ipAccessControlIndex

Entry index.

ipAccessControlSrcAddr

The IP address of the source address.

ipAccessControlSrcMask

The MASK address of the source address.

ipAccessControlDstAddr

The IP address of the destination address.

ipAccessControlDstMask

The MASK address of the destination address.

ipAccessControlOperation

How to operate the IP ACCESS CONTROL statement, on the receiving packet. Forwards the packet, Block (Discard) the packet or block (Discard) the packet and report to the user by sending trap.

ipAccessControlActivation

Does the IP ACCESS CONTROL statement done by HW or SW(CPU). HW - wire-speed, SW - regular.

ipAccessControlProtocol

Over which protocol does the IP ACCESS CONTROL statement activate. Icmp, Tcp, Udp. None - means IP addresses only

ipAccessControlApplication

Over which application does the IP ACCESS CONTROL statement activate. The exception are: above1023 can work over TCP or UDP, none can't work over TCP or UDP or ICMP only none is excepted

ipAccessControlStatus

For create/delete of a IP ACCESS CONTROL statement.

ipRedundancyStatus

Whenever to activate the IP REDUNDANCY mechanism on the device. enable - set by the user, means activate the IP REDUNDANCY mechanism over the defined IP interfaces. disable - set by the user, means don't active the IP REDUNDANCY mechanism over the define ...

ipRedundancyTimeout

Time-out required to activate the backup process of IP REDUNDANCY. After Time-out the Redundant router assumes that the main (Backuped) router is not operational, and takes control over all defined IP interfaces of the main. The value is in seconds. The d ...

ipRedundancyPollingInterval

The polling interval used to poll the Main (Backed up) router. The value is multiply of ipRedundancyTimeout. The value is in seconds. The default value is 3

ipShortcutARPServerStatus

Whenever to activate the ARP Server mechanism on the device. enable - set by the user, means activate the ARP Server mechanism over the defined IP interfaces. disable - set by the user, means don't active the ARP Server mechanism over the defined IP inte ...

ipMulticastInterfaceTable

This table is used to update multicast parameters over interfaces already define

ipMulticastInterfaceEntry

The information concerning one of this entity's interfaces.

ipMulticastInterfaceIfIndex

A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.

ipMulticastInterfaceSendAll

The user will be able to configure whenever to send the all Multicast packets to this interface. Enable - Enable the user to define this interface, over all the existing groups Disable - Will acts according to the other parameters.

ipMulticastInterfaceState

The current state (operational) of the IP Multicast from IP Multicast point of view. It depends on global ipMRouteEnable status and Multicast interface status. Inactive - set by the device (status), Global IP multicast is disabled or Multicast is disable ...

ipMulticastInterfaceStatus

For enable/disable of a IP multicast over an interface.

ipEZ2BoostRouterTable

ipEZ2BoostRouterEntry

ipEZ2BoostRouterSlot

ipEZ2BoostRouterBRAddress

ipEZ2BoostRouterType

ipEZ2BoostRouterStatus

ipEZ2RControlTable

ipEZ2RControlEntry

ipEZ2RControlSlot

ipEZ2RControlBoostedRoutersTimeout

Set the timeout of EZ2route routers

ipEZ2RControlHostsTimeout

Set the timeout of EZ2route hosts

ipEZ2RControlAutoLearnMode

ipVRRPAdminStatus

Global switch to enable/disable VRRP

ipxCircTable

This table is an extention of Novell mib IpxCircTable, and is used to add/delete entries to/from that table. In addition it contains private objects.

ipxCircEntry

The information concerning one of this entity's IPX circuits. An IPX circuit is a logical connection to a certain IPX netNumber.

ipxCircIndex

The identifier of this circuit, unique within the instance of IPX. This value may be written only when creating a new entry in the table.

ipxCircNetNumber

The IPX network number of this circuit.

ipxCircLowerIfAlias

This object is an 'alias' name for the lower-layer interface on top of which this IP interface is defined. The alias is specified by the network manager, and provides a non-volatile 'handle' for the lower-layer interface. The semantics of the object are s ...

ipxCircEncapsulation

The media type (encapsulation of layer2) of this circuit.

ipxCircNetbios

The type of the circuit.

ipxCircStatus

For adding and deleting Circuits. Deleting this row means deleting the corresponding entry in ipxCircTable. Deleting a Circuit also causes deletion of all static routes defined on this Circuit, as well as protocol Circuit (e.g. RIP and SAP) defined on thi ...

ipxCircRipUpdate

The RIP periodic update interval, in seconds.

ipxCircRipAgeMultiplier

The holding multiplier for information received in RIP periodic updates.

ipxCircRipStatus

Indicates whether RIP information may be sent/received over this circuit. Set by the user

ipxCircSapUpdate

The SAP periodic update interval, in seconds.

ipxCircSapAgeMultiplier

The holding multiplier for information received in SAP periodic updates.

ipxCircGetNearestServerReply

Indicates whether to respond to SAP get nearest server requests received on this circuit.

ipxCircSapStatus

Indicates whether SAP information may be sent/received over this circuit.

ipxCircRipState

Indicates whether RIP information may be sent/received over this circuit. Set by the device to reflect the RIP status and the interface status

ipxCircSapState

Indicates whether SAP information may be sent/received over this circuit. Set by the device to reflect the SAP status and the interface status

ipxDestTable

This table replace the Novell mib IpxDestTable, and is used to add/delete entries to/from that table.

ipxDestEntry

The information concerning one of this entity's IPX Routes. An IPX service is a logical connection to a certain IPX Server.

ipxDestNetNum

The IPX network number portion of the IPX address of the destination.

ipxDestProtocol

The routing protocol from which knowledge of this destination was obtained.

ipxDestTicks

The delay in ticks to reach this destination.

ipxDestHopCount

The number of hops necessary to reach the destination.

ipxDestNextHopCircIndex

The unique identifier of the circuit, used to reach the next hop.

ipxDestNextHopNICAddress

The NIC address of the next hop.

ipxDestNextHopNetNum

The IPX network number of the next hop.

ipxDestStatus

ipxDestAge

The age of the Routing table entry.

ipxServTable

This table replace the Novell mib IpxServTable, and is used to add/delete entries to/from that table.

ipxServEntry

The information concerning one of this entity's IPX Services. An IPX service is a logical connection to a certain IPX Server.

ipxServType

The service type.

ipxServName

The server name.

ipxServProtocol

The protocol from which knowledge of this service was obtained.

ipxServNetNum

The IPX network number portion of the IPX address of the service.

ipxServNode

The node portion of the IPX address of the service.

ipxServSocket

The socket portion of the IPX address of the service.

ipxServHopCount

The number of hops to the service.

ipxServStatus

ipxServAge

The age of the SAP entry.

ipxAccessControlEnable

Whenever to activate the IPX ACCESS CONTROL statements on the device. disable means don't activate IPX ACCESS CONTROL over all the IPX statements enable means activate IPX ACCESS CONTROL over all the IPX statements

ipxAccessControlTable

This table is used to add/delete IPX access control statement to/from that table.

ipxAccessControlEntry

The information concerning one of this entity's IPX access control statements.

ipxAccessControlIndex

Entry index.

ipxAccessControlSrcAddr

The IPX network of the source address.

ipxAccessControlDstAddr

The IPX network of the destination address.

ipxAccessControlOperation

How to operate the IPX ACCESS CONTROL statement, on the receiving packet. Forwards the packet, Block (Discard) the packet or block (Discard) the packet and report to the user by sending trap.

ipxAccessControlActivation

Does the IPX ACCESS CONTROL statement done by HW or SW(CPU). HW - wire-speed, SW - regular.

ipxAccessControlStatus

For create/delete of an IPX ACCESS CONTROL statement.

ipxSapFilterEnable

Whenever to activate the IPX SAP Filters statements on the device. disable means don't activate IPX SAP Filters over all the IPX SAP statements enable means activate IPX SAP Filter over all the IPX SAP statements

ipxSapFilterTable

Table of input/output SAP filter according to IPX circuit number.

ipxSapFilterEntry

An entry in the SAP filter table

ipxSapFilterID

ID of SAP filter.

ipxSapFilterCircIndex

.... -- 0xffff means this is a global SAP filter

ipxSapFilterServiceNetNumber

Number network of the filtered service. Value 0xFFFFFFFF applies for any network. DEFVAL {0xFFFFFFFF}

ipxSapFilterServiceType

The type of the service which may be filtered; value 0xFFFF applies for all types of service and it's default DEFVAL {0xFFFF}

ipxSapFilterServerName

The name of the service which may be filtered; wildcards (*) may be used in the end of the name. DEFVAL {*}

ipxSapFilterDirection

Type of filter-input or output

ipxSapFilterAction

Permit/deny receiving/transmitting of SAP entry

ipxSapFilterStatus

....

vlConfTable

This table is an extention of MIB II ifTable, and is used to add/delete entries to/from that table. In addition it contains private objects.

vlConfEntry

The information concerning one of this entity's VLAN interfaces. An VLAN interface is a virtual connection to a switch.

vlConfIndex

A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.

vlConfAlias

This object is an 'alias' name for the lower-layer interface on top of which this IP interface is defined. The alias is specified by the network manager, and provides a non-volatile 'handle' for the lower-layer interface. The semantics of the object are s ...

vlConfStatus

For adding and deleting VLAN interfaces. Deleting this row means deleting the corresponding entry in ifTable (MIB II). Deleting a VLAN interface is allowed only if IP interface is not defined on this VLAN.

vlBridgeTable

For each Bridge segment an entry of this table specifies a set of VLANs, which it contains.

vlBridgeEntry

A entry of this table specifies a Group of VLANs and VLANs belonging to it

vlBridgeProtocol

The protocol, supported by this VLAN. The meanings of the values are: other: none of the following. This VLAN includes any protocol except the following protocols. It is a bridging VLAN. L2 relies on a third-party router to exchange traffic between nodes ...

vlBridgeGroupIndex

A logical number, corresponded this group of VLANs

vlBridgeIndex

A logical number, corresponded this VLAN. Each VLAN is allowed to participate in ONE group only

vlBridgeStatus

It is used to create or delete an entry

layer2GlobalsBridgeEnable

Whenever to activate the Bridge capability on the device. enable - set by the user, means activate the Bridge capability over the defined VLANs. disable - set by the user, means don't active the Bridge capability. backup - set by the user, means the Brid ...

routeGroupTable

routeGroupEntry

routeGroupId

routeGroupRouteMode

A bit mask representing the routing mode of the module: bit 0 - L2 switching bit 1 - EZ2Route bit 2 - Router bit 3 - Rich L2 bit 4 - WebSwitch (Load balance, application redirection). Currently, the following values for this bit mask are defined: secondLa ...

drVlConfTable

This table is an extention of MIB II ifTable, and is used to add/delete entries to/from that table. In addition it contains private objects.

drVlConfEntry

The information concerning one of this entity's VLAN interfaces. An VLAN interface is a virtual connection to a switch.

drVlConfSlot

The slot number of the module

drVlConfIndex

A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.

drVlConfAlias

This object is an 'alias' name for the lower-layer interface on top of which this IP interface is defined. The alias is specified by the network manager, and provides a non-volatile 'handle' for the lower-layer interface. The semantics of the object are s ...

drVlConfStatus

For adding and deleting VLAN interfaces. Deleting this row means deleting the corresponding entry in ifTable (MIB II). Deleting a VLAN interface is allowed only if IP interface is not defined on this VLAN.

drIpInterfaceTable

This table is an extention of MIB II IpAddrTable, and is used to add/delete entries to/from that table. In addition it contains private objects.

drIpInterfaceEntry

The information concerning one of this entity's IP interfaces. An IP interface is a logical connection to a certain IP net/subnet.

drIpInterfaceSlot

The slot number of the module

drIpInterfaceAddr

The IP address to which this entry's addressing information pertains.

drIpInterfaceNetMask

The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.

drIpInterfaceLowerIfAlias

This object is an 'alias' name for the lower-layer interface on top of which this IP interface is defined. The alias is specified by the network manager, and provides a non-volatile 'handle' for the lower-layer interface. The semantics of the object are s ...

drIpInterfaceType

The logical type of the interface. The default depends on the physical type. For example Ethernet and Token-Ring LANs are of type broadcast

drIpInterfaceForwardIpBroadcast

Whether the router forwards IP directed broadcasts that are to be transmitted as link-layer broadcast to an attached net or subnet.

drIpInterfaceBroadcastAddr

The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value wi ...

drIpInterfaceProxyArp

When proxy ARP is enabled, the router responds to ARP requests received on one link-layer interface for an IP-address that is reachable via another link-layer interface. The response provides the router's own MAC address.

drIpInterfaceStatus

For adding and deleting IP interfaces. Deleting this row means deleting the corresponding entry in IpAddrTable (MIB II). Deleting an IP interface also causes deletion of all static routes defined on this IP interface, as well as protocol interfaces (e.g. ...

drIpInterfaceMainRouterAddr

The IP address of the main router backed up on this interface.

drIpInterfaceARPServerStatus

Whenever to activate the ARP Server mechanism on this interface. enable - set by the user, means activate the ARP Server mechanism over this IP interface. disable - set by the user, means don't active the ARP Server mechanism over this IP interface.

drIpInterfaceName

The name of this interface for compatibility with cli.

drIpInterfaceNetbiosRebroadcast

inbound - netbios received from the interface are rebarodcasted, outbound - netbios are rebraodcasted to this interface, both - netbios are rebroadacsted both from and to this interface, disable - netbios is not rebraodcasted neither from nor to this inte ...

drIpInterfaceIcmpRedirects

enable - enable the sending of redirect messages if the router is forced to re-send a packet through the same interface on which it was received. disable - disable the sending of redirect messages on this interface.

drStaticCidrTable

The static route table for this entity. The table includes all static routes, both active and inactive. Note that inactive static routes are deleted from RFC2096 ipCidrRouteTable; Hence the need for this private table to maintain user configuration about ...

drStaticCidrEntry

A particular route to a particular destina- tion, under a particular policy.

drStaticCidrEntID

The Id of the entity for which a set of rows applies. This index is provided as a mean of distributing non-related information on different entities such as physical modules. The value: The module ID (slot number).

drStaticCidrDest

Equivalent to ipCidrRouteDest. The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwis ...

drStaticCidrMask

Equivalent to ipCidrRouteMask. Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the drStaticCidrDest field. For those systems that do not support arbitrary subnet masks, an agent constr ...

drStaticCidrTos

Equivalent to ipCidrRouteTos. The policy specifier is the IP TOS Field. The encoding of IP TOS is as specified by the following convention. Zero indicates the default path if no more specific policy applies. +-----+-----+-----+-----+-----+-----+---- ...

drStaticCidrNextHop

Equivalent to ipCidrRouteNextHop. On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0.

drStaticCidrIfIndex

Equivalent to ipCidrRouteIfIndex. The ifIndex value which identifies the local interface through which the next hop of this route should be reached.

drStaticCidrType

Equivalent to ipCidrRouteType. The type of route. Note that local(3) refers to a route for which the next hop is the final destination; remote(4) refers to a route for which the next hop is not the final destina- tion. reject (2) refers to a rou ...

drStaticCidrMetric1

Equivalent to ipCidrRouteMetric1. The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's drStaticCidrProto value. If this metric is not used, its value should be ...

drStaticCidrPrecedence

Equivalent to ipCidrRouteMetric5 (our use of it). The precedence of this routing rule, compared to other routes which may have been learned vie other methods. Translates into ipCidrRouteMetric5 in ipCidrRouteTable (RFC2096). Higher values mean lower prec ...

drStaticCidrStatus

Creation, activation, de-activation and deletion of a static route, using the RowStatus convention: active(1), notInService(2) ,notReady(3), createAndGo(4), createAndWait(5), destroy(6). when an entry is placed in the notInService state, the corresponding ...