PowerNet-MIB Download

mconfigNumTrapReceivers

The number of managers to send traps to.

mconfigTrapReceiverTable

A list of managers to send traps to. The number of entries is given by the value of mconfigNumTrapReceivers. Maximum number of Trap Receivers is four.

mconfigTrapReceiverEntry

The managers to send traps to.

trapIndex

The index to a trap receiver entry.

receiverAddr

The IP address of the manager to send a trap to.

communityString

The community name to use in the trap when sent to the manager.

severity

The severity threshold of traps to send to the manager. traps are labeled in severity as informational(1), warning(2), severe(3). Only traps of equal or greater severity than this value are sent to the manager.

acceptThisReceiver

An entry will become active if yes, and will be deleted if no.

receiveTrapType

The node in this entry will receive traps defined in APC PowerNet MIB, if this OID is set to yes.

mconfigBOOTPEnabled

The value of yes(1) indicates the PowerNet Adapter is configured to obtain its IP configuration parameters from a BOOTP server. The value of no(2) indicates adapter will assume IP configuration parameters values saved in adapter's eeprom, which was orgini ...

mconfigTFTPServerIP

The IP address of TFTP server. If mconfigBOOTPEnabled is yes(1), then this IP address is provided by BOOTP server and not allowed to be modified; otherwise, this IP address can be modified. Before using TFTP to load new code image, the image file should b ...

newCodeAuthentViaTFTP

Once mcontrolRestartAgent is set to loadAndExecuteNewAgent (3), PowerNet adapter will start to load the remote image file, for authentication only, instead of saving the code into flash memory. Only if a validNewAgentCodeImage (1) is found will the agent ...

mcontrolRestartAgent

Setting this OID to restartCurrentAgent (1) will restart the same SNMP agent code currently saved in flash memory. Setting this OID to loadAndExecuteNewAgent (3) will enable adapter to load a new agent code into the flash memory and start to execute this ...

powerNetSoftwareSystemDescription

A brief description of the PowerNet sub-agent.

powerNetSoftwareOid

The object identifier of the PowerNet sub-agent.

powerNetSoftwareSystemUpTime

The time that the sub-agent has been running.

powerNetSoftwareTableSize

The number of software modules supporting the UPS.

powerNetSoftwareTable

A list of the software monitoring the UPS.

powerNetSoftwareEntry

An entry containing information on a software module.

moduleNumber

The index into the Software Entry Table

moduleName

The name of the software module.

moduleVersion

The version of the software module.

moduleDate

The date of the software module represented as mm-dd-yy.

upsBasicIdentModel

The UPS model name (e.g. 'APC Smart-UPS 600').

upsBasicIdentName

An 8 byte ID string identifying the UPS. This object can be set by the administrator.

upsAdvIdentFirmwareRevision

The firmware revision of the UPS system's microprocessor.

upsAdvIdentDateOfManufacture

The date when the UPS was manufactured in mm/dd/yy format.

upsAdvIdentSerialNumber

An 8-character string identifying the serial number of the UPS internal microprocessor. This number is set at the factory. NOTE: This number does NOT correspond to the serial number on the rear of the UPS.

upsBasicBatteryStatus

The status of the UPS batteries. A batteryLow(3) value indicates the UPS will be unable to sustain the current load, and its services will be lost if power is not restored. The amount of run time in reserve at the time of low battery can be configured b ...

upsBasicBatteryTimeOnBattery

The elapsed time since the UPS has switched to battery power.

upsBasicBatteryLastReplaceDate

The date when the UPS system's batteries were last replaced in mm/dd/yy format. For Smart-UPS models, this value is originally set in the factory. When the UPS batteries are replaced, this value should be reset by the administrator.

upsAdvBatteryCapacity

The remaining battery capacity expressed in percent of full capacity.

upsAdvBatteryTemperature

The current internal UPS temperature expressed in Celsius.

upsAdvBatteryRunTimeRemaining

The UPS battery run time remaining before battery exhaustion.

upsAdvBatteryReplaceIndicator

Indicates whether the UPS batteries need replacing.

upsAdvBatteryNumOfBattPacks

The number of external battery packs connected to the UPS. If the UPS does not use smart cells then the agent reports ERROR_NO_SUCH_NAME.

upsAdvBatteryNumOfBadBattPacks

The number of external battery packs connected to the UPS that are defective. If the UPS does not use smart cells then the agent reports ERROR_NO_SUCH_NAME.

upsBasicInputPhase

The current AC input phase.

upsAdvInputLineVoltage

The current utility line voltage in VAC.

upsAdvInputMaxLineVoltage

The maximum utility line voltage in VAC over the previous 1 minute period.

upsAdvInputMinLineVoltage

The minimum utility line voltage in VAC over the previous 1 minute period.

upsAdvInputFrequency

The current input frequency to the UPS system in Hz.

upsAdvInputLineFailCause

The reason for the occurrence of the last transfer to UPS battery power. The variable is set to: - noTransfer(1) -- if there is no transfer yet. - highLineVoltage(2) -- if the transfer to battery is caused by an over voltage greater than the high transfe ...

upsBasicOutputStatus

The current state of the UPS. If the UPS is unable to determine the state of the UPS this variable is set to unknown(1).

upsBasicOutputPhase

The current output phase.

upsAdvOutputVoltage

The output voltage of the UPS system in VAC.

upsAdvOutputFrequency

The current output frequency of the UPS system in Hz.

upsAdvOutputLoad

The current UPS load expressed in percent of rated capacity.

upsAdvOutputCurrent

The current in ampres drawn by the load on the UPS.

upsBasicConfigNumDevices

The number of devices that are plugged into the UPS.

upsBasicConfigDeviceTable

A list of devices that are plugged into the UPS. The number of entries is given by the value of upsBasicConfigNumDevices.

upsBasicConfigDeviceEntry

The devices plugged in to the UPS.

deviceIndex

The index of the device that is plugged into the UPS.

deviceName

The name/description of the device plugged into the UPS.

vaRating

The volt-amp rating of the device plugged into the UPS.

acceptThisDevice

An entry is added if yes, the entry is deleted if no.

upsAdvConfigRatedOutputVoltage

The nominal output voltage from the UPS in VAC. Possible values are 100, 120, 208, 220, 225, 230 and 240. NOTE: Only units that are 220, 225, 230 and 240 can be changed. Allowable set values are 220, 225, 230, and 240. For these adjustable units, if a va ...

upsAdvConfigHighTransferVolt

The maximum line voltage in VAC allowed before the UPS system transfers to battery backup. Allowed values depend on the UPS used: 100 volt units allow settings of 108, 110, 112, and 114. 120 volt units allow settings of 129, 132, 135, and 138. 208 volt un ...

upsAdvConfigLowTransferVolt

The minimum line voltage in VAC allowed before the UPS system transfers to battery backup. Allowable values depend on the UPS used: 100 volt units allow settings of 81, 83, 85, 87. 120 volt units allow settings of 97, 100, 103, 106. 208 volt units allow s ...

upsAdvConfigAlarm

A flag indicating how the UPS should handle audible line fail alarms.

upsAdvConfigAlarmTimer

The time after initial line failure at which the UPS begins emitting audible alarms (beeping). This timer is observerd only if the value of extControlAlarm is timed(2). Allowed values are 0 or 30 seconds. If a value other than a supported value is provid ...

upsAdvConfigMinReturnCapacity

The minimum battery capacity required before the UPS will return from a low battery shutdown condition. The capacity is measured from 0% battery capacity (or Low Battery) as a percent of full capacity (100%). In other words, the UPS will not re-energiz ...

upsAdvConfigSensitivity

The sensitivity of the UPS to utility line abnormalities or noises.

upsAdvConfigLowBatteryRunTime

The desired run time of the UPS, in seconds, once the low battery condition is reached. Allowed values are 120, 300, 420, or 600 seconds. During this time the UPS will produce a constant warning tone which can not be disabled. If a value other than a su ...

upsAdvConfigReturnDelay

The delay in seconds after utility line power returns before the UPS will turn on. This value is also used when the UPS comes out of a reboot and before the UPS wakes up from 'sleep' mode. Allowed values are 0, 60, 180 and 300 seconds. If a value other ...

upsAdvConfigShutoffDelay

The delay in seconds the UPS remains on after being told to turn off. Allowed values are 20, 180, 300, and 600 seconds. If a value other than a supported value is provided in a set request, the UPS interprets it as a the next higher acceptable value. If ...

upsAdvConfigUpsSleepTime

The time in seconds for the UPS to go to 'sleep' when instructed. When in sleep mode, the UPS will not provide output power regardless of the input line state. Once the specified time has elapsed, output power will be restored. This is a configuration s ...

upsAdvConfigSetEEPROMDefaults

WRITE: Resets the UPS EEPROM variables to default values. READ: returns 0

upsAdvConfigDipSwitchSetting

Current settings of UPS dip switches.

upsAdvConfigDipSwitchEntry

The current setting of one dip switch.

dipSwitchIndex

The index of a UPS dip switch.

dipSwitchStatus

The setting of a UPS dip switch.

upsAdvConfigBattExhaustThresh

The number of seconds prior to battery exhaustion when the UPS will switch off power to it's load.

upsAdvConfigPassword

The password entered at the UPS front panel to enable local configuation of the EEProm. If the password is disabled or is not supported, then the agent returns a null string.

upsAdvConfigAllowedSetTable

The table listing the allowed values for all discrete configurable UPS variables.

apcUpsConfigEntry

The table entry for a configurable UPS variable.

apcUpsConfigFieldIndex

The index to an eeprom field entry.

apcUpsConfigFieldOID

The OID of the current configurable value.

apcUpsConfigFieldValueRange

The distcrete set of allowed values of a configurable register. Individual values are delimited by a comma.

upsBasicControlConserveBattery

Setting this variable to turnUpsOffToConserveBattery(2) causes a UPS on battery to be put into 'sleep' mode. The UPS will turn back on when utility power is restored. Attempting to turn off a UPS that is not on battery will result in a badValue error. Se ...

upsAdvControlUpsOff

Setting this variable to turnUpsOff(2) causes the UPS to shut off. When in this state, the UPS will not provide output power regardless of the input line state. The ON/OFF switch on the UPS must be toggled for the UPS to return to operation. Setting thi ...

upsAdvControlRebootUps

Setting this variable to rebootUps(2) causes the UPS to shut off and turn back on. Setting this value to noRebootUps(1) has no effect. The value noRebootUps(1) will always be returned when the variable is read.

upsAdvControlUpsSleep

Setting this variable to putUpsToSleep(2) causes the UPS to go to sleep for the time specified by upsAdvConfigUpsSleepTime. When in sleep mode, the UPS will not provide output power regardless of the input line state. Once the specified time has elapsed, ...

upsAdvControlSimulatePowerFail

Setting this variable to simulatePowerFailure(2) causes the UPS switch to battery power. Setting this value to noSimulatePowerFailure(1) has no effect. The value noSimulatePowerFailure(1) will always be returned when the variable is read.

upsAdvControlFlashAndBeep

Setting this variable to flashAndBeep(2) causes the UPS to beep and simultaneously turn on the UPS front panel lights (Smart-UPS only). Setting this value to noFlashAndBeep(1) has no effect. The value noFlashAndBeep(1) will always be returned when the var ...

upsAdvControlTurnOnUPS

Setting this variable to turnOnUPS(2) causes the UPS to be turned on immediately, provided upsBasicOutputStatus does not read ON. Setting this value to noTurnOnUPS(1) has no effect. The value noTurnOnUPS(1) will always be returned when the variable is rea ...

upsAdvControlBypassSwitch

This switch pertains to the Matrix UPS. It switchs the UPS in or out of bypass mode.

upsAdvTestDiagnosticSchedule

The UPS system's automatic battery test schedule.

upsAdvTestDiagnostics

Setting this variable to testDiagnostics(2) causes the UPS to perform a diagnostic self test. Setting this value to noTestDiagnostics(1) has no effect. The value noTestDiagnostics(1) will always be returned when the variable is read.

upsAdvTestDiagnosticsResults

The results of the last UPS diagnostics test performed.

upsAdvTestLastDiagnosticsDate

The date the last UPS diagnostics test was performed in mm/dd/yy format.

upsAdvTestRuntimeCalibration

Setting this variable to performCalibration(2) causes the UPS to discharge to calibrate the UPS. The test will only start if the battery capacity is 100%. The test runs until capacity is less than 25%. Setting this variable to cancelCurrentCalibration(3) ...

upsAdvTestCalibrationResults

The results of the last runtime calibration. Value ok(1) means a successful runtime calibration. Value invalidCalibration(2) indicates last calibration did not take place since the battery capacity was below 100%. Value calibrationInProgress(3) means a ca ...

upsAdvTestCalibrationDate

The date the last UPS runtime calibration was performed in mm/dd/yy format.

upsCommStatus

The status of agent's communication with UPS.

mUpsEnvironAmbientTemperature

The ambient temperature in Celsius.

mUpsEnvironRelativeHumidity

The relative humidity as a percentage.

mUpsContactNumContacts

The number of contacts supported by the Measure-UPS.

mUpsContactTable

A list of contacts supported by the Measure-UPS.

mUpsContactEntry

A contact entry containing information for a given contact.

contactNumber

An index identifying the contact on the Measure-UPS.

normalState

The normal operating position of the contact. If the normal operating postion cannot be set then it is contolled via the dip switch on the Measure-UPS and is therefore read-only.

description

The decsription of the purpose/use of the contact.

monitoringStatus

A flag indicating whether this contact is monitored, or not.

currentStatus

This value indicates the current state of the contact. If the contact is not in its normal state. This value is set to fault(2).

serialPort2Mode

Setting this variable to passthrough will enable mini's port2 behave like a UPS port. Choosing localConsole will enable the port to be used as local console.

setPulseOnTXD

Setting this variable to setPulseOnTXD(2) causes adapter to generate a PULSE on TXD pin of serial port 2. The duration in the prototype implementation will be 1 second. Setting this value to noSetPulseOnTXD(1) has no effect. The value noSetPulseOnTXD(1) w ...