The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for "port operation"
- atmx Port Operation Status
- atmxPortOperStatus 1.3.6.1.4.1.800.2.4.1.1.1.7 (defined in XYLAN-ATM-MIB)
The operational state (i.e., actual) of this port. The ILMI should not alarm on a physical interface for when the value of this object is outOfService(3). This capability is useful if the equipment is to be disconnected, or for troubleshooting purposes. A value of loopBack(4) indicates that a local loopback is in place. - port Operation Status
- portOperStatus 1.3.6.1.4.1.43.1.12.3.1.1.4.1.1.4 (defined in 3comab9300)
Operational status of the port. - Character Port Operation Status
- charPortOperStatus 1.3.6.1.2.1.19.2.1.7 (defined in rfc1316)
The port's actual, operational state, independent of flow control. 'up' indicates able to function normally. 'down' indicates inability to function for administrative or operational reasons. 'maintenance' indicates a maintenance mode, exclusive of normal operation, such as running a test. 'absent' indicates that port hardware is not present. 'active' indicates up with a user present (e.g. logged in). - Repeater Port Operation Status
- rptrPortOperStatus 1.3.6.1.2.1.22.1.3.1.1.5 (defined in rfc1516)
This object indicates the port's operational status. The notPresent(3) status indicates the port is physically removed (note this may or may not be possible depending on the type of port.) The operational(1) status indicates that the port is enabled (see rptrPortAdminStatus) and working, even though it might be auto-partitioned (see rptrPortAutoPartitionState). If this object has the value operational(1) and rptrPortAdminStatus is set to disabled(2), it is expected that this object's value will soon change to notOperational(2). - Character Port Operation Status
- charPortOperStatus 1.3.6.1.2.1.19.2.1.7 (defined in rfc1658)
The port's actual, operational state, independent of flow control. 'up' indicates able to function normally. 'down' indicates inability to function for administrative or operational reasons. 'maintenance' indicates a maintenance mode, exclusive of normal operation, such as running a test. 'absent' indicates that port hardware is not present. 'active' indicates up with a user present (e.g. logged in). 'up' and 'active' correspond to ifOperStatus 'up'. 'down' and 'absent' correspond to ifOperStatus 'down'. 'maintenance' corresponds to ifOperStatus 'test'. - sdlc Port Operation Type
- sdlcPortOperType 1.3.6.1.2.1.41.1.1.2.1.3 (defined in rfc1747)
This parameter defines whether the SDLC port is currently operating as though connected to a leased or switched line. - sdlc Port Operation SERVLIM
- sdlcPortOperSERVLIM 1.3.6.1.2.1.41.1.1.2.1.9 (defined in rfc1747)
This object describes the number of times the active poll list is currently being traversed before polling a station on the slow poll list for a primary, multipoint SDLC port. This object only has meaning for SDLC ports where sdlcPortOperRole == primary and sdlcPortOperTopology == multipoint - sdlc Port Operation Last Fail Time
- sdlcPortOperLastFailTime 1.3.6.1.2.1.41.1.1.2.1.12 (defined in rfc1747)
This object describes the value of sysUpTime when this SDLC port last failed. If the port has not failed, then this value shall be zero. - sdlc Core Port Operation Group
- sdlcCorePortOperGroup 1.3.6.1.2.1.41.1.4.2.1.2 (defined in rfc1747)
The sdlcCorePortOperGroup defines objects which are common to the PortOper group of all compliant link stations. - Cabletron Bridge Load Share Port Operation Status
- ctBridgeLoadSharePortOperStatus 1.3.6.1.4.1.52.4.1.2.3.10.2.1.4 (defined in ctron-bridge-mib)
The operational state of the port associated with this instance of load share. - Cabletron DLSw Port Operation Status
- ctdlswPortOperStatus 1.3.6.1.4.1.52.4.1.2.8.2.1.1.5 (defined in ctron-dlsw-mib)
Specifies the current operating status of DLSw frame forwarding for this port. - Token Ring Port Management Port Operation State
- tRingPortMgmtPortOperState 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.5 (defined in dot5-log-mib)
Returns the operational state of this port. - dot5 Physical Management Port Common Port Operation State
- dot5PhysMgmtPortCommonPortOperState 1.3.6.1.4.1.52.4.1.1.6.1.3.1.1.1.5 (defined in dot5-phys-mib)
Returns the operational state of this token ring port. - garp Port Operation Application Type
- garpPortOperationAppType 1.3.6.1.4.1.52.4.2.12.1.3.2.2.1.1 (defined in garp-mib)
Protocol that this operation status belongs to. A 1 represents GMRP and 2 represents GVRP. - garp Port Operation Status
- garpPortOperationStatus 1.3.6.1.4.1.52.4.2.12.1.3.2.2.1.3 (defined in garp-mib)
The port operational status for this application. A 1 represents enabled and 2 represents disabled. - sta Port Operation Edge Port
- staPortOperEdgePort 1.3.6.1.4.1.52.4.12.30.1.5.2.1.5 (defined in v2h124-24-mib)
The operational value of the Edge Port parameter. The object is initialized to the value of staPortAdminEdgePort and is set FALSE when a BPDU is received. - sta Port Operation Point To Point
- staPortOperPointToPoint 1.3.6.1.4.1.52.4.12.30.1.5.2.1.7 (defined in v2h124-24-mib)
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by explicit configuration or by auto-detection, as described in the staPortAdminPointToPoint object. - Enterasys Mstp Port Operation Path Cost
- etsysMstpPortOperPathCost 1.3.6.1.4.1.5624.1.2.28.1.3.1.1.5 (defined in enterasys-mstp-mib)
The operational value for the contribution of this port to the path cost of paths towards the root of the corresponding Spanning Tree instance. - appn Port Operation State
- appnPortOperState 1.3.6.1.2.1.34.4.1.1.4.1.1.3 (defined in APPN-MIB)
Indicates the current state of this port: inactive(1) - port is inactive pendactive(2) - port is pending active active(3) - port is active pendinact(4) - port is pending inactive - Cisco ATM Forum Port Operation Status
- atmfPortOperStatus 1.3.6.1.4.1.353.2.1.1.1.5 (defined in ATM-FORUM-MIB)
This object should not be implemented except as required for backward compatibility with version 3.1 of the UNI specification. Appropriate Network Management MIBs should be used instead. - Cisco Access Control List QoS Ip Ace Destination Port Operation
- caqIpAceDestPortOp 1.3.6.1.4.1.9.9.179.1.3.2.1.14 (defined in CISCO-CATOS-ACL-QOS-MIB)
Indicates how a packet's destination TCP/UDP port number is to be compared. If the caqIpAceProtocolType object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(1)' and cannot be changed while this row is active, i.e., the value of caqIpAceStatus in the same row has the value 'active(1)'. 'noOperator(1)', which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. lt(2) means less than. gt(3) means greater than. eq(4) means equal. neq(5) means not equal. Those 4 operators are using the caqIpAceDestPort object as an operand which is the only one needed. range(6) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is caqIpAceDestPort object, and the other operand is the ending port number of the range which the caqIpAceDestPortRange object is in. - Cisco Access Control List QoS Ip Download Ace Destination Port Operation
- caqIpDownloadAceDestPortOp 1.3.6.1.4.1.9.9.179.1.10.2.1.13 (defined in CISCO-CATOS-ACL-QOS-MIB)
Indicates how a packet's destination TCP/UDP port number is to be compared. 'noOperator', which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. 'lt' means less than. 'gt' means greater than. 'eq' means equal. 'neq' means not equal. Those 4 operators are using the caqIpDownloadAceDestPort object as an operand which is the only one needed. 'range' means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is caqIpDownloadAceDestPort object, and the other operand is the ending port number of the range which the caqIpDownloadAceDestPortRange object is in. - Cisco Enhanced Benes Fabric Bundle Port Operation State
- cfhBundlePortOperState 1.3.6.1.4.1.9.9.257.1.4.2.1.4 (defined in CISCO-FABRIC-HFR-MIB)
The object indicates the operational state of the fabric bundle port. unknown - the bundle port state is unknown or in the transition between 'up' and 'down' state. up - bundle port operates normally down - bundle port was downed due to error condition or administratively shutdown. - Fibre Channel Management Port Operation Type
- cfcmPortOperType 1.3.6.1.4.1.9.10.999999.1.3.1.5 (defined in CISCO-FC-MGMT-MIB)
The current operational type of this port. - Fibre Channel Management Port Operation Protocols
- cfcmPortOperProtocols 1.3.6.1.4.1.9.10.999999.1.3.1.14 (defined in CISCO-FC-MGMT-MIB)
A bit mask specifying the higher level protocols which are currently operational on this port. For Fx_Ports, E_Ports and B_Ports, this object will typically have the value 'unknown'. - hp Fddi Driver Stats Error Gsr Port Operation
- hpFddiDriverStatsErrGsrPortOp 1.3.6.1.4.1.11.2.14.11.5.1.2.3.2.1.17 (defined in hpprocurve-drivers)
The number of port operation errors detected by the FSI of the MC68840 FDDI network interface chip. - hp Fddi Driver Stats Error Gsr Port Operation
- hpFddiDriverStatsErrGsrPortOp 1.3.6.1.4.1.11.2.14.11.5.1.2.3.2.1.17 (defined in hpprocurve-v2-drivers)
The number of port operation errors detected by the FSI of the MC68840 FDDI network interface chip. - llc Port Operation Table
- llcPortOperTable 1.3.6.1.3.51.1.1.2 (defined in ibm-llc)
This table contains current LLC port parameters. Many of these objects have corresponding objects inthe llcPortAdminTable. - llc Port Operation Entry
- llcPortOperEntry 1.3.6.1.3.51.1.1.2.1 (defined in ibm-llc)
Currently set parameters for a specific LLC port. - llc Port Operation Last Fail Time
- llcPortOperLastFailTime 1.3.6.1.3.51.1.1.2.1.4 (defined in ibm-llc)
This object describes the value of sysUpTime when this LLC port last failed. If the port has not failed, then this value shall be zero. - Juniper MI Mst Cist Port Operation Edge Status
- jnxMIMstCistPortOperEdgeStatus 1.3.6.1.4.1.2636.3.46.1.1.6.1.10 (defined in JUNIPER-MIMSTP-MIB)
The operational value of the Edge Port parameter. The object is initialized to the value of jnxMIMstCistPortAdminEdgeStatus and is set FALSE on reception of a BPDU. - Juniper MI Mst Cist Port Operation Version
- jnxMIMstCistPortOperVersion 1.3.6.1.4.1.2636.3.46.1.1.6.1.41 (defined in JUNIPER-MIMSTP-MIB)
This indicates whether the Port is operationally in the Mstp mode, Rstp mode or the Stp-compatible mode i.e., whether the Port is transmitting MST BPDUs, RST BPDUs or Config/TCN BPDUs. - line Port Operation Status
- linePortOperStatus 1.3.6.1.4.1.3646.1300.2.1.12.1.1.2 (defined in ASKEY-SYSTEM-MIB)
This object indicates the line port's operational status. The notPresent(3) status indicates the line port is physically removed (note this may or may not be possible depending on the type of port). The operational(1) status indicates that the port is enabled (see rptrPortAdminStatus) and working, even though it might be auto-partitioned (see rptrPortAutoPartitionState). If this object has the value operational(1) and rptrPortAdminStatus is set to disabled(2), it is expected that this object's value will soon change to notOperational(2). - Switch L2 Stp Port Operation Edge Port
- swL2StpPortOperEdgePort 1.3.6.1.4.1.171.11.70.5.2.16.4.1.9 (defined in DES3010F-L2MGMT-MIB)
The operational value of the Edge Port parameter. The object is initialized to the value of swL2StpPortAdminEdgePort and is set FALSE on reception of a BPDU. - Switch L2 Stp Port Operation Point To Point
- swL2StpPortOperPointToPoint 1.3.6.1.4.1.171.11.70.5.2.16.4.1.11 (defined in DES3010F-L2MGMT-MIB)
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the swL2StpPortAdminPointToPoint object. - Switch L2 Stp Port Operation Edge Port
- swL2StpPortOperEdgePort 1.3.6.1.4.1.171.11.70.5.2.16.4.1.9 (defined in DES3010FL-L2MGMT-MIB)
The operational value of the Edge Port parameter. The object is initialized to the value of swL2StpPortAdminEdgePort and is set FALSE on reception of a BPDU. - Switch L2 Stp Port Operation Point To Point
- swL2StpPortOperPointToPoint 1.3.6.1.4.1.171.11.70.5.2.16.4.1.11 (defined in DES3010FL-L2MGMT-MIB)
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the swL2StpPortAdminPointToPoint object. - Switch L2 Stp Port Operation Edge Port
- swL2StpPortOperEdgePort 1.3.6.1.4.1.171.11.70.5.2.16.4.1.9 (defined in DES3010G-L2MGMT-MIB)
The operational value of the Edge Port parameter. The object is initialized to the value of swL2StpPortAdminEdgePort and is set FALSE on reception of a BPDU. - Switch L2 Stp Port Operation Point To Point
- swL2StpPortOperPointToPoint 1.3.6.1.4.1.171.11.70.5.2.16.4.1.11 (defined in DES3010G-L2MGMT-MIB)
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the swL2StpPortAdminPointToPoint object. - Switch L2 Stp Port Operation Edge Port
- swL2StpPortOperEdgePort 1.3.6.1.4.1.171.11.70.5.2.16.4.1.9 (defined in DES3018-L2MGMT-MIB)
The operational value of the Edge Port parameter. The object is initialized to the value of swL2StpPortAdminEdgePort and is set FALSE on reception of a BPDU. - Switch L2 Stp Port Operation Point To Point
- swL2StpPortOperPointToPoint 1.3.6.1.4.1.171.11.70.5.2.16.4.1.11 (defined in DES3018-L2MGMT-MIB)
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the swL2StpPortAdminPointToPoint object. - Switch L2 Stp Port Operation Edge Port
- swL2StpPortOperEdgePort 1.3.6.1.4.1.171.11.70.5.2.16.4.1.9 (defined in DES3026-L2MGMT-MIB)
The operational value of the Edge Port parameter. The object is initialized to the value of swL2StpPortAdminEdgePort and is set FALSE on reception of a BPDU. - Switch L2 Stp Port Operation Point To Point
- swL2StpPortOperPointToPoint 1.3.6.1.4.1.171.11.70.5.2.16.4.1.11 (defined in DES3026-L2MGMT-MIB)
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the swL2StpPortAdminPointToPoint object.
