CISCO-ATM-RM-MIB Download
The MIB module which complements standard ATM MIBs for Cisco devices,
for Resource Management.
IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges,
Firewalls, Repeaters.
OID list for CISCO-ATM-RM-MIB
- rmSwitchOverSubFactor
- The Over Subscription Factor (OSF) is used on switch startup/OIR to determine the maximum sizes of VBR-NRT and ABR/UBR queues. In general, the larger the value of OSF specified, the larger the queues are made at startup. Denoting the maximum sizes of CBR, ...
- rmSwitchScrMarginFactor
- The Sustained Cell Rate Margin Factor (SCRMF) is used in Connection Admission Control (CAC) of VBR connections to vary the weight given to the difference between Sustained Cell Rate (scr) and Peak Cell Rate (pcr) specified in the traffic contract. When ca ...
- rmSwitchAbrCongNotify
- The ABR Congestion Notification object determines the type of congestion notification used on ABR connections in the switch. This notification can be done either via relative-rate or Explicit Forward Congestion Indication marking in ATM cells, or both.
- rmDefaultQosObjectiveTable
- The (conceptual) table containing Resource Management configuration information for default Quality of Service objective values used when a signalling request is received on a UNI interface.
- rmDefaultQosObjectiveEntry
- An entry (conceptual row) in the rmDefaultQosObjectiveTable containing Resource Management configuration for the default UNI QOS objectives. Rows are identified by Service Category.
- rmDefaultQosServiceCategory
- The Service Category to which the row applies.
- rmScDefaultQosMaxCtd
- The default Maximum Cell Transfer Delay (ctd) for the Service Category. It applies only to cbr and vbr-rt Service Categories. Specifying a value of 16777215 signifies that this parameter should not be checked during connection setup. The units of this obj ...
- rmScDefaultQosPeakToPeakCdv
- The default Peak-to-peak cell delay variation (cdv) for the Service Category. It applies only to cbr and vbr-rt Service Categories. Specifying a value of 16777215 signifies that this parameter should not be checked during connection setup. The units of th ...
- rmScDefaultQosClr
- The default cell-loss-ratio for the Service Category (for CLP=0 cells only). Specifying a value of 0 signifies that this parameter should not be checked during connection setup. The units of this object are negative powers of ten (so an object value of 8 ...
- rmScDefaultQosClrClp01
- The default cell-loss-ratio for the Service Category for CLP=0+1 cells. Specifying a value of 0 signifies that this parameter should not be checked during connection setup. The units of this object are negative powers of ten (so an object value of 8 means ...
- sharedMemRmSwitchQueuedCellTable
- The (conceptual) table containing Resource Management information on the cells in the output queues of a shared-memory output-queued ATM switch.
- sharedMemRmSwitchQueuedCellEntry
- An entry (conceptual row) in the sharedMemRmSwitchQueuedCellTable containing Resource Management information on the cells in the output queues of a shared-memory switch. Rows are indexed by priority.
- sharedMemRmCellPriority
- The cell priority. The cell priority maps one-to-one to the per-interface queues specified by the sharedMemRmIfOutputQ object. All cells of a connection of a particular Service Category are given a fixed priority. The Service Categories allocated to a pri ...
- sharedMemRmSwitchQueuedCellLimit
- Configured limit on the number of cells on all output queues of the switch at any time of a particular priority.
- sharedMemRmSwitchQueuedCellCount
- Count of the number of cells on all output queues of the switch at any time of a particular priority.
- rmIfCfgTable
- The (conceptual) table containing Resource Management configuration information for whole ATM interfaces.
- rmIfCfgEntry
- An entry (conceptual row) in the rmIfCfgTable containing Resource Management configuration for an ATM interface. The particular interface is identified by the value of MIB-II's ifIndex.
- rmIfOutPacingRateRequested
- This object reflects an explicit configuration of the state of pacing for this interface. If the value of this object is 0, pacing is disabled on this interface. Prior to any user configuration, the value of this object is 0. If the value not 0, it repres ...
- rmIfOutPacingRateInstalled
- The output pacing value, in kilobits per second, in effect. A value of 0 indicates output pacing is disabled. This object is not instantiated for interfaces to which it cannot be applied.
- rmIfOutPacingForce
- A Set Request for rmIfOutPacingRateRequested that does not reduce the port rate below the currently allocated bandwidth guarantees for the output flow always succeeds irrespective of the value of rmIfOutPacingForce. But a Set Request for rmIfOutPacingRat ...
- rmIfLinkDistance
- The link distance defined for the interface, expressed in kilometers. This is then divided by the speed of light to determine a propagation delay.
- rmIfBestEffortLimit
- The limit on the number of Best Effort connections that can be established on this interface. Note that a change to this value affects subsequent connection setup, not existing connections. A value of 4294967295 disables best-effort limits.
- rmIfCbrDefaultRxUpcTolerance
- Specifies the GCRA limit parameter used for policing of a receive cell-stream of a CBR connection on an interface, if the limit parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to thi ...
- rmIfVbrRtDefaultRxUpcTolerance
- Specifies the maximum burst size parameter used for policing of a receive cell-stream of a VBR-RT connection on an interface, if this parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change ...
- rmIfVbrNrtDefaultRxUpcTolerance
- Specifies the maximum burst size parameter used for policing of a receive cell-stream of a VBR-NRT connection on an interface, if this parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change ...
- rmIfAbrDefaultRxUpcTolerance
- Specifies the GCRA limit parameter used for policing of a receive cell-stream of an ABR connection on an interface, if the limit parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to th ...
- rmIfUbrDefaultRxUpcTolerance
- Specifies the GCRA limit parameter used for policing of a receive cell-stream of a UBR connection on an interface, if the limit parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a change to thi ...
- rmIfVbrRtDefaultRxUpcCdvt
- Specifies the GCRA limit parameter used for peak-rate policing of a receive cell-stream of a VBR-RT connection on an interface, if the CDVT parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a c ...
- rmIfVbrNrtDefaultRxUpcCdvt
- Specifies the GCRA limit parameter used for peak-rate policing of a receive cell-stream of a VBR-NRT connection on an interface, if the CDVT parameter is not specified explicitly in the connection setup request. It is specified in cell-times. Note that a ...
- rmIfServCategorySupport
- The value of this object controls and reflects the Service Category(s) supported on this ATM interface. If a bit is set, the corresponding Service Category is supported on the interface, and CAC will allow such connections. If a bit is reset, the correspo ...
- rmIfFramingOverhead
- If this object is set to true, framing overhead will be taken into account in determining the Maximum Cell Rate that is possible on this interface. If this object is set to false, framing overhead will not figure in the determination of the Maximum Cell R ...
- rmIfFramingOverheadForce
- A Set Request for rmIfFramingOverhead that does not reduce the Maximum Guaranteed Services Bandwidth of this interface below the currently allocated bandwidth guarantees always succeeds irrespective of the value of rmIfFramingOverheadForce. But a Set Requ ...
- rmIfOverBooking
- This object specifies overbooking on this interface as a percentage of the Maximum Cell Rate that is possible on this interface. If the value of this object is 100, overbooking is disabled on this interface. A set request for this object will succeed only ...
- rmIfVbrRtPerClassOverbooking
- This object specifies the Per Class Overbooking percentage for VBR-rt service category on this interface. If the value of this object is 100, Per Class Overbooking for VBR-rt is disabled on this interface. Specifying a value that is greater than 100 cause ...
- rmIfVbrNrtPerClassOverbooking
- This object specifies the Per Class Overbooking percentage for VBR-Nrt service category on this interface. If the value of this object is 100, Per Class Overbooking for VBR-Nrt is disabled on this interface. Specifying a value that is greater than 100 cau ...
- rmIfAbrPerClassOverbooking
- This object specifies the Per Class Overbooking percentage for ABR service category on this interface. If the value of this object is 100, Per Class Overbooking for ABR is disabled on this interface. Specifying a value that is greater than 100 causes the ...
- rmIfUbrPerClassOverbooking
- This object specifies the Per Class Overbooking percentage for UBR service category on this interface. If the value of this object is 100, Per Class Overbooking for UBR is disabled on this interface. Specifying a value that is greater than 100 causes the ...
- rmIfDirectionCfgTable
- The (conceptual) table containing Resource Management configuration information for a single direction of traffic flow on ATM interfaces.
- rmIfDirectionCfgEntry
- An entry (conceptual row) in the rmIfInOutCfgTable containing Resource Management configuration for a traffic direction on an ATM interface. The particular interface is identified by the value of MIB-II's ifIndex, and the direction of flow.
- rmIfDirection
- Selects the traffic direction for which subsequent row parameters are read or written. In is received from the port(into the device), Out is transmitted to the port (from the device).
- rmIfDirControlLinkShareMaxAgg
- Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum aggregate Guaranteed Service (CBR or VBR) traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic directi ...
- rmIfDirControlLinkShareMinCbr
- Configuration in the Controller Link Sharing (CLS) scheme. Specifies a minimum amount of CBR traffic that can be reserved in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after o ...
- rmIfDirControlLinkShareMaxCbr
- Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum CBR traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output p ...
- rmIfDirControlLinkShareMinVbr
- Configuration in the Controller Link Sharing (CLS) scheme. Specifies a minimum amount of VBR traffic that can be reserved in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after o ...
- rmIfDirControlLinkShareMaxVbr
- Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum VBR traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output p ...
- rmIfDirMaxCbrPcr
- Specifies the maximum Peak-cell-rate (pcr) traffic parameter that can be specified for CBR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that ...
- rmIfDirMaxCbrTolerance
- Specifies the maximum limit parameter used in the GCRA algorithm for traffic policing that can be specified for CBR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of this paramet ...
- rmIfDirMaxVbrPcr
- Specifies the maximum Peak-cell-rate (pcr) traffic parameter that can be specified for VBR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that ...
- rmIfDirMaxVbrScr
- Specifies the maximum Sustained-cell-rate (scr) traffic parameter that can be specified for VBR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note ...
- rmIfDirMaxVbrTolerance
- Specifies the maximum limit parameter used in the GCRA algorithm for traffic policing that can be specified for VBR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of this paramet ...
- rmIfDirMaxAbrPcr
- Specifies the maximum Peak-cell-rate (pcr) traffic parameter that can be specified for ABR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that ...
- rmIfDirMaxAbrTolerance
- Specifies the maximum limit parameter used in the GCRA algorithm for traffic policing that can be specified for ABR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of this paramet ...
- rmIfDirMaxUbrPcr
- Specifies the maximum Peak-cell-rate (pcr) traffic parameter that can be specified for UBR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note that ...
- rmIfDirMaxUbrTolerance
- Specifies the maximum limit parameter used in the GCRA algorithm for traffic policing that can be specified for UBR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of this paramet ...
- rmIfDirMaxAbrMcr
- Specifies the maximum Minimum-cell-rate (mcr) traffic parameter that can be specified for ABR connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checking of this parameter limit. Note t ...
- rmIfDirMaxUbrMcr
- Specifies the maximum Minimum-cell-rate (mcr) traffic parameter that can be specified for UBR plus (UBR with an mcr guaranteed) connections in a traffic direction on an interface. It is specified in cells-per-second. A value of 4294967295 disables checki ...
- rmIfDirMaxVbrCdvt
- Specifies the maximum peak-rate CDVT parameter used in the GCRA algorithm for traffic policing that can be specified for VBR connections in a traffic direction on an interface. It is specified in cell-times. A value of 4294967295 disables checking of thi ...
- rmIfDirControlLinkShareMinAbr
- Configuration in the Controller Link Sharing (CLS) scheme. Specifies a minimum amount of ABR traffic that can be reserved in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after o ...
- rmIfDirControlLinkShareMaxAbr
- Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum ABR traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after output p ...
- rmIfDirControlLinkShareMinUbr
- Configuration in the Controller Link Sharing (CLS) scheme. Specifies a minimum amount of UBR plus (UBR with an mcr guaranteed) traffic that can be reserved in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic dir ...
- rmIfDirControlLinkShareMaxUbr
- Configuration in the Controller Link Sharing (CLS) scheme. Specifies the maximum UBR plus traffic that can be allocated in a traffic direction on an interface. It is expressed as a percentage of the maximum traffic direction's bandwidth (applies after out ...
- rmIfServiceCategoryStateTable
- The (conceptual) table containing Resource Management state information for ATM interfaces by Service Category.
- rmIfServiceCategoryStateEntry
- An entry (conceptual row) in the rmIfServiceCategoryStateTable containing Resource Management configuration for an ATM interface. Rows are identified by the value of MIB-II's ifIndex, and the Service Category.
- rmIfSc
- The Service Category to which the row applies.
- rmIfScRxAcr
- The Available Cell Rate (specified in cells per second) for traffic received on the interface for this Service Category. This is the bandwidth available for connections. For CBR and VBR Service Categories, this value decreases as a result of connection se ...
- rmIfScTxAcr
- The Available Cell Rate (specified in cells per second) for traffic sent out the interface for this Service Category. This is the bandwidth available for connections. For CBR and VBR Service Categories, this value decreases as a result of connection setup ...
- rmIfScRxAlcr
- The Allocated Cell Rate (specified in cells per second) for traffic received on the interface for this Service Category. This is the bandwidth allocated-to connections. For CBR and VBR Service Categories, this value increases as a result of connection set ...
- rmIfScTxAlcr
- The Allocated Cell Rate (specified in cells per second) for traffic sent out the interface for this Service Category. This is the bandwidth allocated-to connections. For Guaranteed Service Categories, this value increases as a result of connection setup a ...
- rmIfScNumSvxConns
- The number of signalled connections (VC or VP) of this Service Category currently allocated on the interface.
- rmIfScNumPvxConns
- The number of permanent connections (VC or VP) of this Service Category currently allocated on the interface.
- rmIfScTxMaxCtd
- The maximum Cell Transfer Delay estimated to be experienced by cells of connections transmitted out this interface of this Service Category. This is estimate does not distinguish between clp0 and clp1 cells. This object is valid for Service Category cbr ...
- rmIfScTxP2PeakCdv
- The Peak-to-Peak Cell Delay Variation estimated to be experienced by cells of connections transmitted out this interface of this Service Category. This estimate does not distinguish between clp0 and clp1 cells. This object is valid for Service Categorie ...
- rmIfScTxClr
- The Cell Loss Ratio estimated to be experienced by cells of connections transmitted out this interface of this Service Category. This is an estimate for clp0 cells only. The unit of this object is negative power of ten (so an object value of 8 means 10* ...
- rmIfScTxClrClp01
- The Cell Loss Ratio estimated to be experienced by cells of connections transmitted out this interface of this Service Category. This is an estimate for clp0+1 cells. The unit of this object is negative power of ten (so an object value of 8 means 10**(- ...
- rmIfScRxDynBwSvcAcr
- The Available Cell Rate (specified in cells per second) for traffic received on the interface for this Service Category. This object is valid only for IMA physical interfaces. This is the bandwidth available for SVC connections. For CBR and VBR Service ...
- rmIfScTxDynBwSvcAcr
- The Available Cell Rate (specified in cells per second) for traffic transmitted on the interface for this Service Category. This object is valid only for IMA physical interfaces. This is the bandwidth available for SVC connections on physical interfaces ...
- rmIfServiceCategoryStatisticsTable
- The (conceptual) table containing Resource Management statistics information for ATM interfaces by Service Category.
- rmIfServiceCategoryStatisticsEntry
- An entry (conceptual row) in the rmIfServiceCategoryStatisticsTable containing Resource Management configuration for an ATM interface. Rows are identified by the value of MIB-II's ifIndex, and the Service Category.
- rmIfScRcacResultNumAdmit
- The number of successful resource allocation requests for this interface.
- rmIfScRcacResultNumTotalRequests
- The total number of resource allocation requests for this interface.
- rmIfScRcacResultNumFailTraffComb
- The number of resource allocation requests which are considered to be in error due to an unsupported combination of traffic parameters. An example of this would be, for a VBR connection, a zero maximum burst-size given a non-zero sustainable-cell-rate.
- rmIfScRcacResultNumFailBw
- The number of resource allocation requests which are considered to be in error due to a lack of bandwidth. This will never occur for Best Effort Service Categories.
- rmIfScRcacResultNumFailLoss
- The number of resource allocation requests which are considered to be in error due to exceeding cell loss criterion.
- rmIfScRcacResultNumFailDelay
- The number of resource allocation requests which are considered to be in error due to exceeding maximum delay criterion.
- rmIfScRcacResultNumFailCdv
- The number of resource allocation requests which are considered to be in error due to exceeding cell delay variation criterion.
- rmIfScRcacResultNumFailBeLimit
- The number of resource allocation requests which are considered to be in error due to exceeding a limit on the number of Best-Effort connections.
- rmIfScRcacResultNumFailParmLimit
- The number of resource allocation requests which are considered to be in error due to exceeding a traffic parameter limit criterion.
- rmIfScRcacResultNumFailOther
- The number of resource allocation requests which are considered to be in error for a reason not enumerated by other counter objects.
- sharedMemRmIfOutputQCfgTable
- The (conceptual) table containing configuration information for ATM physical interface output queues. This table is not instantiated for interfaces to which it cannot be applied.
- sharedMemRmIfOutputQCfgEntry
- An entry (conceptual row) in the sharedMemRmIfOutputQCfgTable containing Resource Management configuration for an ATM interface. A particular row is identified by the value of MIB-II's ifIndex, and the output queue.
- sharedMemRmIfOutputQ
- The output queue on this ATM interface.
- sharedMemRmIfOutputQServCategory
- The service category(s) sharing this output queue on this ATM interface. The various bit positions are: 1 constant bit rate (cbr) 2 variable bit rate-real time (vbr-rt) 4 variable bit rate-non real time (vbr-nrt) 8 available bit rate (abr) 16 ...
- sharedMemRmIfOutputQRequestedMaxSize
- This object reflects an explicit configuration of the maximum number of cells that may occupy this queue. If the value of this object is 0, the maximum size in effect is a default value calculated by software. Prior to any user configuration, the value of ...
- sharedMemRmIfOutputQInstalledMaxSize
- The maximum number of cells that may occupy this queue. Will be a multiple of 32. Explicit configuration of maximum size are made via the object sharedMemrmIfOutputQRequestedMaxSize. Such requests are rounded up to the nearest multiple of 32 prior to inst ...
- sharedMemRmIfOutputQMaxSizeForce
- Must be set to forceChange to allow changing of sharedMemRmIfOutputQRequestedMaxSize for a queue on an interface that is 'up'. This is because such a change causes the interface to lose data while the size is changed. Once the change takes place, the forc ...
- sharedMemRmIfOutputQCellCount
- Count of the number of cells in the output queue.
- sharedMemRmIfThresholdCfgTable
- The (conceptual) table containing the output queue thresholds used on ATM physical interface output queues. These are specified per Service Category. This table is not instantiated for interfaces to which it cannot be applied.
- sharedMemRmIfThresholdCfgEntry
- An entry (conceptual row) in the sharedMemRmIfThresholdCfgTable containing Resource Management configuration for an ATM interface. A particular row is identified by the value of MIB-II's ifIndex, and the Service Category.
- sharedMemRmIfDiscardThreshold
- The output queue CLP/EPD threshold for this Service Category on this ATM interface. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold.
- sharedMemRmIfEfciThreshold
- The output queue EFCI marking threshold for this Service Category on this ATM interface. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold.
- sharedMemRmIfAbrRelativeRateThreshold
- The ABR Relative-rate marking queue congestion threshold for the ABR queue on this ATM interface. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. This object is only defined for the abr service category.
- lsPerVcqRmThreshGrpTable
- The (conceptual) table containing information for Switch Threshold Groups. When cells are queued in the switch for a direction of cell traffic on an ATM connection (VC or VP), several functions related to queueing are dictated by the congestion state (ful ...
- lsPerVcqRmThreshGrpEntry
- An entry (conceptual row) in the lsPerVcqRmThreshGrpTable containing Resource Management configuration for a Threshold Group. All entries ever in the table are present at startup, none are created dynamically.
- lsPerVcqRmThreshGrp
- The Threshold Group specified by this entry.
- lsPerVcqRmThreshGrpMaxSize
- This object specifies the maximum number of cells that may occupy this Threshold Group. While any integer in the range can be set, the hardware granularity is in 64-cell units. Therefore, the value installed is [(value / 64) * 64] + 63. If the value of th ...
- lsPerVcqRmThreshGrpQMaxSize
- This object reflects an explicit configuration of the maximum limit on the number of cells that may occupy connection queues that are a member of this Threshold Group. A connection queue that is a member of this Threshold Group will never have more cells ...
- lsPerVcqRmThreshGrpQMinSize
- This object reflects an explicit configuration of the minimum limit on the number of cells that may occupy connection queues that are a member of this Threshold Group. The Threshold Group at it's most congested will not limit a connection queue to fewer t ...
- lsPerVcqRmThreshGrpDiscThreshold
- The output queue CLP/EPD threshold for this Threshold Group. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. Setting this object to -1 restores the default value for the Threshold Group. The granularity of th ...
- lsPerVcqRmThreshGrpMarkThreshold
- The output queue EFCI/ABR-RR marking threshold for this Threshold Group. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. Setting this object to -1 restores the default value for the Threshold Group. The granu ...
- lsPerVcqRmThreshGrpName
- The name associated with the threshold-group. If this is set to the null-string, the default name for the Threshold Group is assigned.
- lsPerVcqRmThreshGrpCellCount
- Count of the number of cells in the Threshold Group.
- lsPerVcqRmThreshGrpServiceTable
- The (conceptual) table specifying which VC or VP queues are assigned to a Threshold Group.
- lsPerVcqRmThreshGrpServiceEntry
- An entry (conceptual row) in the lsPerVcqRmThreshGrpServiceTable. All entries ever in the table are present at startup, none are created dynamically.
- lsPerVcqRmThreshGrpService
- The Service specified by this entry.
- lsPerVcqRmThreshGrpServGroup
- The Threshold Group to which VC/VP queues specified by the service are assigned. Changing the assignment of service to Threshold Group does not alter the assignment for connections currently installed in hardware, but those connections that are subsequent ...
- lsPerVcqRmHierarchicalSchedulingMode
- On a LS1010 equipped with the Lightstream per-VC queueing chipset, the user can define Hierarchical VP-Tunnels. Each such tunnel has its own dedicated scheduler, programmed to output data at a configurable maximum rate. Therefore, the overall output of th ...
- cgrPerVcqRmThreshGrpTable
- The (conceptual) table containing information for Switch Threshold Groups. When cells are queued in the switch for a direction of cell traffic on an ATM connection (VC or VP), several functions related to queueing are dictated by the congestion state (ful ...
- cgrPerVcqRmThreshGrpEntry
- An entry (conceptual row) in the cgrPerVcqRmThreshGrpTable containing Resource Management configuration for a Threshold Group. All entries ever in the table are present at startup, none are created dynamically.
- cgrPerVcqModuleId
- The switching module specified by this entry.
- cgrPerVcqRmThreshGrp
- The Threshold Group specified by this entry.
- cgrPerVcqRmThreshGrpMaxSize
- This object specifies the maximum number of cells that may occupy this Threshold Group. While any integer in the range can be set, the hardware granularity is in 64-cell units. Therefore, the value installed is [(value / 64) * 64] + 63. Even though the ma ...
- cgrPerVcqRmThreshGrpQMaxSize
- This object reflects an explicit configuration of the maximum limit on the number of cells that may occupy connection queues that are a member of this Threshold Group. A connection queue that is a member of this Threshold Group will never have more cells ...
- cgrPerVcqRmThreshGrpQMinSize
- This object reflects an explicit configuration of the minimum limit on the number of cells that may occupy connection queues that are a member of this Threshold Group. The Threshold Group at it's most congested will not limit a connection queue to fewer t ...
- cgrPerVcqRmThreshGrpDiscThreshold
- The output queue CLP/EPD threshold for this Threshold Group. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. Setting this object to -1 restores the default value for the Threshold Group. The granularity of th ...
- cgrPerVcqRmThreshGrpMarkThreshold
- The output queue EFCI/ABR-RR marking threshold for this Threshold Group. This is expressed in percent-of-full. Note that 100% full effectively turns off the threshold. Setting this object to -1 restores the default value for the Threshold Group. The granu ...
- cgrPerVcqRmThreshGrpName
- The name associated with the threshold-group. If this is set to the null-string, the default name for the Threshold Group is assigned.
- cgrPerVcqRmThreshGrpCellCount
- Count of the number of cells in the Threshold Group.
- cgrPerVcqRmThreshGrpServiceTable
- The (conceptual) table specifying which VC or VP queues are assigned to a Threshold Group. This table is supported only on the Catalyst8540MSR Platform.
- cgrPerVcqRmThreshGrpServiceEntry
- An entry (conceptual row) in the cgrPerVcqRmThreshGrpServiceTable. All entries ever in the table are present at startup, none are created dynamically.
- cgrPerVcqRmThreshGrpService
- The Service specified by this entry.
- cgrPerVcqRmThreshGrpServGroup
- The Threshold Group to which VC/VP queues specified by the service are assigned. Changing the assignment of service to Threshold Group does not alter the assignment for connections currently installed in hardware, but those connections that are subsequent ...
- cgrPerVcqRmHierarchicalSchedulingMode
- On a Catalyst8540 MSR, the user can define Hierarchical VP-Tunnels. Each such tunnel has its own dedicated scheduler, programmed to output data at a configurable maximum rate. Therefore, the overall output of the Hierarchical VP-tunnel is rate-limited. In ...
- lsPerVcqRmIfTable
- The (conceptual) table containing configuration information for ATM physical interfaces.
- lsPerVcqRmIfEntry
- An entry (conceptual row) in the lsPerVcqRmIfTable containing Resource Management configuration for an ATM interface. An entry in the table is present when an entry in the ifTable is created for an ATM interface that uses the Lighstream per-VC queueing ch ...
- lsPerVcqRmIfMinWrrServiceClass
- The service classes on an interface are partitioned into two subsets, dictating how a service class with a cell ready to transmit is chosen (subsequently a connection is chosen within the selected service class). There are two subsets: Strict Priority (SP ...
- lsPerVcqRmIfServiceClassTable
- The (conceptual) table containing configuration information for ATM physical interface Service Classes (not logical port ATM interfaces). An ATM connection (VC or VP) on an interface is a member of a Service Class. The Service Class is used in the schedul ...
- lsPerVcqRmIfServiceClassEntry
- An entry (conceptual row) in the lsPerVcqRmIfServiceClassTable containing Resource Management configuration for an ATM interface. A particular row is identified by the value of MIB-II's ifIndex, and the output queue. An entry in the table is present when ...
- lsPerVcqRmIfServiceClass
- The service class on this ATM interface.
- lsPerVcqRmIfServClassConnType
- The types of connections using this service class on this ATM interface. The various bit positions are: 1 constant bit rate (cbr) 2 variable bit rate-real time (vbr-rt) 4 variable bit rate-non real time (vbr-nrt) 8 available bit rate (abr) 16 ...
- lsPerVcqRmIfServClassWrrWeight
- Configure the weighting specified for a service class to make the scheduling decision among active service classes in the WRR subset.
- rmTrafficShaperIfTable
- The (conceptual) table containing ATM Traffic Shaper configuration and state information for ATM interfaces.
- rmTrafficShaperIfEntry
- An entry (conceptual row) in the rmTrafficShaperIfTable containing Traffic Shaper configuration and state information for an ATM interface. The particular interface is identified by the value of MIB-II's ifIndex.
- rtsIfMaxThreshold
- This object reflects the value of the Maximum Threshold installed in the traffic shaper hardware for this interface. This object is expressed in number of cell buffers. This object is not instantiated for interfaces to which it cannot be applied.
- rtsIfCellCount
- This object contains the count of cells queued to this interface in the traffic shaping hardware. This object is not instantiated for interfaces to which it cannot be applied.
- rtsIfVbrCfgRequested
- If this object is set to the value 'shapingDisable', VBR connections(VC or VP) on this interface will not be shaped. If the object is set to the value 'shapeToScrAndPcr', the VBR (VC or VP) connections on this interface will be shaped to conform to their ...
- rtsIfVbrCfgInstalled
- This object reflects the current VBR Traffic Shaping configuration installed in the hardware. This object is not instantiated for interfaces to which it cannot be applied.
- rtsIfBeCfgRequested
- This object reflects the traffic shaping configuration applied to Best-Effort Connections(VC or VP) belonging to UBR and ABR service categories on this interface. If this object is set to the value 'shapingDisable', best-effort connections(VC or VP) on th ...
- rtsIfBeCfgInstalled
- This object reflects the current Best-Effort Traffic Shaping configuration installed in the hardware. This object is not instantiated for interfaces to which it cannot be applied.
- rtsIfVbrClassMaxThrshRequested
- This object specifies the Traffic Shaper Maximum Cell Buffer Threshold for the VBR Traffic Class. The value of this object is expressed as a percent of the value of rtsIfMaxThreshold object. A set request for this object will succeed only if the value of ...
- rtsIfVbrClassMaxThrshInstalled
- This object reflects the value of Maximum Class Threshold for VBR Traffic Class, in number of cell buffers, that is installed in the Traffic Shaping hardware. This object is not instantiated for interfaces to which it cannot be applied.
- rtsIfBeClassMaxThrshRequested
- This object specifies the Traffic Shaper Maximum Cell Buffer Threshold for the Best-Effort Traffic Class. The value of this object is expressed as a percent of the value of rtsIfMaxThreshold object. A set request for this object will succeed only if the ...
- rtsIfBeClassMaxThrshInstalled
- This object reflects the value of Maximum Class Threshold for Best-Effort Traffic Class, in number of cell buffers, that is installed in the Traffic Shaping hardware. This object is not instantiated for interfaces to which it cannot be applied.
- rtsIfVbrVcMaxThrshRequested
- This object reflects the Maximum Threshold of the per-connection queues of VBR connections(VCs or VPs) in the traffic shaping hardware. The value of this object is expressed in number of cell buffers. Any change made to the value of this object will only ...
- rtsIfVbrVcMaxThrshInstalled
- This object reflects the Maximum Threshold for the per-connection queues of VBR connections(VCs or VPs) that is installed in the Traffic Shaping hardware. The value of this object is expressed in number of cell buffers. This object is not instantiated fo ...
- rtsIfBeVcMaxThrshRequested
- This object reflects the Maximum Threshold of the per-connection queues of best-effort connections(VCs or VPs) in the traffic shaping hardware. The value of this object is expressed in number of cell buffers. Any change made to the value of this object w ...
- rtsIfBeVcMaxThrshInstalled
- This object reflects the Maximum Threshold for the per-connection queues of Best-Effort connections(VCs or VPs) that is installed in the Traffic Shaping hardware. The value of this object is expressed in number of cell buffers. This object is not instan ...
- atmRmSwitchCfgMIBGroup
- A collection of objects which provide ATM Switch Resource Management configuration.
- sharedMemAtmRmSwitchMIBGroup
- A collection of objects which provide ATM Switch Resource Management information global to a shared-memory ATM switch.
- atmRmPhyIfCfgMIBGroup
- A collection of objects which provide ATM interface Resource Management configuration for physical interfaces.
- atmRmAllIfCfgMIBGroup
- A collection of objects which provide ATM interface Resource Management configuration for all interfaces.
- atmRmIfAllStateMIBGroup
- A collection of objects which provide ATM interface Resource Management status for all interfaces.
- atmRmIfStatsMIBGroup
- A collection of objects which provide ATM Switch Resource Management statistics.
- sharedMemAtmRmPhyIfMIBGroup
- A collection of objects which provide ATM interface Resource Management information for physical interfaces of a shared-memory ATM switch.
- atmRmSwitchCfgMIBGroup2
- A collection of objects which provide ATM Switch Resource Management configuration.
- atmRmPhyIfCfgMIBGroup2
- A collection of objects which provide ATM interface Resource Management configuration for physical interfaces.
- atmRmIfAllStateMIBGroup2
- A collection of objects which provide ATM interface Resource Management status for all interfaces.
- lsPerVcqAtmRmGroup
- A collection of objects which provide ATM Resource Management status on platforms using the Lightstream per-VC queueing chipset.
- atmRmPhyIfCfgMIBGroup3
- A collection of objects which provide ATM interface Resource Management configuration for physical interfaces.
- atmRmAllIfCfgMIBGroup2
- A collection of objects which provide ATM interface Resource Management configuration for all interfaces.
- atmRmAllIfCfgMIBGroup3
- A collection of objects which provide ATM interface Resource Management configuration for all interfaces.
- lsPerVcqAtmRmGroup2
- A collection of objects which provide ATM Resource Management status on platforms using the Lightstream per-VC queueing chipset.
- cgrPerVcqAtmRmGroup
- A collection of objects which provide ATM Resource Management status on the Catalyst8540MSR platform.
- atmRmAllIfCfgMIBGroup4
- A collection of objects which provide ATM interface Resource Management configuration for all interfaces.
- atmRmPhyIfCfgMIBGroup4
- A collection of objects which provide ATM interface Resource Management configuration for physical interfaces.
- atmRmPhyIfCfgMIBGroup5
- A collection of objects which provide ATM interface Resource Management configuration for physical interfaces.
- atmRmIfAllStateMIBGroup3
- A collection of objects which provide ATM interface Resource Management status for all interfaces.
- atmRmAllIfCfgMIBGroup5
- A collection of objects which provide ATM interface Resource Management configuration for all interfaces.
- cgrPerVcqAtmRmGroup2
- A collection of objects which provide ATM Resource Management status on the Catalyst8540MSR platform.
- atmRmTrafficShaperIfGroup
- A collection of objects which provide ATM Traffic Shaper configuration and state information for ATM interfaces.
- atmRmAllIfCfgMIBGroup6
- A collection of objects which provide ATM interface Resource Management configuration for all interfaces.
Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.
