CISCO-DOCS-EXT-MIB Download

cdxQosCtrlUpTable

For each upstream interface, this table maintains a number of objects related to Quality of Service scheduler which uses these attributes to control cable modem registration.

cdxQosCtrlUpEntry

A list of attributes for each upstream MAC scheduler that supports Quality of Service. Entries in this table exist for each ifEntry with ifType of docsCableUpstream(129).

cdxQosCtrlUpAdmissionCtrl

The admission control status for minimum guaranteed upstream bandwidth scheduling service requests for this upstream. When this object is set to 'true', if there is a new modem with minimum guaranteed upstream bandwidth scheduling service in its QoS class ...

cdxQosCtrlUpMaxRsvdBWPercent

The percentage of upstream maximum reserved bandwidth to the raw bandwidth if the admission control is enabled on this upstream. For example, if the upstream interface has raw bandwidth 1,600,000 bits/second and cdxQosCtrlUpMaxRsvdBWPercent is 200 percent ...

cdxQosCtrlUpAdmissionRejects

The count of cable modem registration requests rejected on this upstream interface due to insufficient reserved bandwidth for serving the cable modems with Unsolicited Grant Service (UGS) scheduling service when UGS is supported and for serving the cable ...

cdxQosCtrlUpReservedBW

The current total reserved bandwidth in bits per second of this upstream interface. It is the sum of all cable modems' minimum guaranteed bandwidth in bits per second currently supported on this upstream.

cdxQosCtrlUpMaxVirtualBW

The maximum virtual bandwidth capacity of this upstream interface if the admission control is enabled. It is the raw bandwidth in bits per second times the percentage. If the admission control is disabled, then this object will contain the value zero.

cdxQosIfRateLimitTable

This table describes the attributes of rate limiting for schedulers in cable upstream and downstream interfaces that support Quality of Service. The rate limiting process is to ensure the Quality of Service and fairness.

cdxQosIfRateLimitEntry

List of the rate limiting attributes for cable upstream and downstream interfaces schedulers that support Quality of Service. Entries in this table exist for each ifEntry with ifType of docsCableUpstream(129) and docsCableDownstream(128).

cdxQosIfRateLimitAlgm

To ensure fairness, the CMTS will throttle the rate for bandwidth request (upstream)/packet sent (downstream) at which CMTS issues grants(upstream) or allow packet to be send(downstream) such that the flow never gets more than its provisioned peak rate in ...

cdxQosIfRateLimitExpWt

Weight for exponential moving average of loss rate for weighted excess packet discard algorithm to maintain. The higher value of the weight makes the algorithm more sensitive to the recent bandwidth usage by the Sid. The default value is 1 and whenever th ...

cdxQosIfRateLimitShpMaxDelay

The maximum shaping delay in milliseconds. That is, the maximum amount time of buffering the CMTS will allow for any rate exceeded flow. If the max buffering delay is large, the grants/packets of the flow will be buffered for a longer period of time even ...

cdxQosIfRateLimitShpGranularity

The width in milliseconds of each element in shaping delay queue, that is, the shaping granularity. The shaping granularity is only applied to rate limit algorithm: Token bucket algorithm with shaping. It controls how accurately the algorithm quantizes th ...

cdxCmtsServiceExtTable

The list contains the additional attributes of a single Service ID that provided by docsIfCmtsServiceEntry.

cdxCmtsServiceExtEntry

Additional objects for docsIfCmtsServiceTable entry including downstream traffic statistics and excess counts against the Quality of Service limits for each Service ID. From DOCSIS 1.1 onwards statistics are maintained for each Service Flow(instead of the ...

cdxIfCmtsServiceOutOctets

The cumulative number of Packet Data octets sent for this Service ID.

cdxIfCmtsServiceOutPackets

The cumulative number of Packet data packets sent for this Service ID.

cdxQosMaxUpBWExcessRequests

The number of upstream bandwidth requests which exceeds the maximum upstream bandwidth allowed for a service defined in the Quality of Service profile associated with this Sid. The request which exceeds the maximum upstream bandwidth allowed will be rejec ...

cdxQosMaxDownBWExcessPackets

The number of downstream bandwidth packets which exceeds the maximum downstream bandwidth allowed for a service defined in the Quality of Service profile associated with this Sid. The packet which exceeds the maximum downstream bandwidth allowed will be d ...

cdxUpInfoElemStatsTable

The table contains the attributes of a particular Information Element type for each instance of the MAC scheduler. It is indexed by upstream ifIndex. An Entry exists for each ifEntry with ifType of docsCableUpstream(129) Since each upstream has an instanc ...

cdxUpInfoElemStatsEntry

The list of statistics for a type of Information Element (IE) which defines the allowed usage for a range of upstream mini slots. One entry exists for each Information Element (IE) in a upstream which ifType is docsCableUpstream (12).

cdxUpInfoElemStatsNameCode

This entry describes the Information Element (IE) type. Enumerations are : reqIE(1) : Request Information Element, The request Information Element provides an upstream interval in which a CM can request the CMTS for bandwidth on the upstream chan ...

cdxUpInfoElemStatsIEType

The current number of mini-slots used for the Information Element type. The value is only a snapshot since the current number of mini-slots of this IE type could be changing rapidly.

cdxBWQueueTable

This table describes the attributes of queues in cable interfaces schedulers that support Quality of Service.

cdxBWQueueEntry

The list of queue attributes in cable upstream and downstream interfaces schedulers that supports Quality of Service. Entries in this table exist for each ifEntry with ifType of docsCableUpstream(129) and docsCableDownstream(128).

cdxBWQueueNameCode

The name code for the queue. cirQ :CIR queue. The queue is for Committed Information Rate (CIR) type of service which serves Service IDs which have minimum guaranteed rate in its QoS profile. It is applicable if CMTS is running is either of DOCSIS 1.0 or ...

cdxBWQueueOrder

The relative order of this queue to the other queues within the cable interface. The smaller number has higher order. That is, 0 is the highest order and 10 is the lowest order. The scheduler will serve the requests in higher order queue up to the number ...

cdxBWQueueNumServedBeforeYield

The maximum number of requests/packets the scheduler can serve before yielding to another queue. The value 0 means all requests must be served before yielding to another queue. The range is 0-50 for DOCSIS 1.0 and for DOCSIS 1.1 it is 0-64.

cdxBWQueueType

The queuing type which decides the position of a request/packet within the queue. unknown : queue type unknown. other : not fifo, and not priority. fifo : first in first out. priority: each bandwidth request has a priority and the position of the req ...

cdxBWQueueMaxDepth

The maximum number of requests/packets which the queue can support. The range is 0-50 for DOCSIS1.0 and for DOCSIS1.1 it is 0-64.

cdxBWQueueDepth

The current number of requests/packets in the queue. The range is 0-50 for DOCSIS1.0 and for DOCSIS1.1 it is 0-64.

cdxBWQueueDiscards

The number of requests/packets discarded because of queue overflow (queue depth > queue maximum depth).

cdxCmCpeTable

This table contains information about cable modems (CM) or Customer Premises Equipments (CPE).

cdxCmCpeEntry

The list contains information for a cable modem (CM) or a Customer Premises Equipment (CPE). An entry exist for each cable modem supported by CMTS and each Customer Premises Equipment connected to a cable modem supported by CMTS.

cdxCmCpeMacAddress

The Mac address to identify a cable modem or a Customer Premises Equipment.

cdxCmCpeType

Indicate this entry is for cable modem or Customer Premises Equipment. The enumerations are: cm(1): cable modem cpe(2): Customer Premises Equipment

cdxCmCpeIpAddress

Ip address of the cable modem or Customer Premises Equipment.

cdxCmCpeIfIndex

The CMTS cable MAC interface index (ifType of docsCableMaclayer(127)) that cable modem or Customer Premises Equipment connects to. Use cdxCmCpeIfIndex and cdxCmCpeCmtsServiceId to identify an entry in docsIfCmtsServiceTable.

cdxCmCpeCmtsServiceId

The cable modem's primary Service ID if the type is cm. The primary Service ID for the CM which the CPE connects if the type is cpe. Use cdxCmCpeIfIndex and cdxCmCpeCmtsServiceId to identify an entry in docsIfCmtsServiceTable.

cdxCmCpeCmStatusIndex

Pointer to an entry in docsIfCmtsCmStatusTable identifying status of the CM (which the CPE connects to.)

cdxCmCpeAccessGroup

ASCII text to identify the Access Group for a CM or CPE. Access Group is to filter the upstream traffic for that CM or CPE.

cdxCmCpeResetNow

Setting this object to true(1) causes the device to reset. Reading this object always returns false(2). For cdxCmCpeType value cm(1), CMTS removes the CM from the Station Maintenance List and would cause the CM to reset its interface. For cdxCmCpeType v ...

cdxCmCpeDeleteNow

Setting this object to true(1) causes the CM/CPE to be deleted. Reading this object always returns false(2). For cdxCmCpeType value cm(1), CMTS delete CM from its interface. For cdxCmCpeType value cpe(2), CMTS delete CPE from its associated CM.

cdxCmtsCmStatusExtTable

The list contains the additional CM status information.

cdxCmtsCmStatusExtEntry

Additional objects for docsIfCmtsCmStatusTable entry.

cdxCmtsCmStatusValue

Current Cable Modem connectivity state. The object extends states in docsIfCmtsCmStatusValue in more details. The enumerations are: offline(1) : modem considered offline. others(2) : states is in docsIfCmtsCmStatusValue. ini ...

cdxIfCmtsCmStatusOnlineTimes

The number of times that the modem changes the connectivity state from 'offline' to 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmtsCmStatusValu ...

cdxIfCmtsCmStatusPercentOnline

The percentage of time that the modem stays 'online' over the time period from the modem's first ranging message received by CMTS until now. The value for this object is 100 times bigger than the real percentage value. For example, 32.15% will be value 32 ...

cdxIfCmtsCmStatusMinOnlineTime

The minimum period of time the modem stayed 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmtsCmStatusValue is any of the values: online(5), onlin ...

cdxIfCmtsCmStatusAvgOnlineTime

The average period of time the modem stayed 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmtsCmStatusValue is any of the values: online(5), onlin ...

cdxIfCmtsCmStatusMaxOnlineTime

The maximum period of time the modem stayed 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmtsCmStatusValue is any of the values: online(5), onlin ...

cdxIfCmtsCmStatusMinOfflineTime

The minimum period of time modem stayed 'offline' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmtsCmStatusValue is any of the values: online(5), onlineNe ...

cdxIfCmtsCmStatusAvgOfflineTime

The average period of time the modem stayed 'offline' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmtsCmStatusValue is any of the values: online(5), onli ...

cdxIfCmtsCmStatusMaxOfflineTime

The maximum period of time the modem stayed 'offline' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmtsCmStatusValue is any of the values: online(5), onli ...

cdxIfCmtsCmStatusDynSidCount

The number of active dynamic SIDs on this modem. Prior to getting the assigned the Service Flow IDs(SFID) the CM must must complete a number of protocol transactions. The CMTS assigns a temporary Service ID (SID) to complete these steps.

cdxIfCmtsCmStatusAddlInfo

This object indicates additional attributes regarding the CM. 1. noisyPlant indicates that the CM connection is noisy. 2. modemPowerMaxOut indicates that the modem has reached its maximum power level. A bit of of this object is set to 1 if the condition i ...

cdxIfCmtsCmStatusOnlineTimesNum

The number of times that the modem changes the connectivity state from 'offline' to 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmtsCmStatusValu ...

cdxIfCmtsCmStatusLastResetTime

The last cable modem connectivity statistics reset time. If the value of this object is '0', then the cable modem connectivity statistics had not been reset.

cdxCmtsMacExtTable

This table contains the additions attributes of a CMTS MAC interface that provided by docsIfCmtsMacTable.

cdxCmtsMacExtEntry

Additional objects for docsIfCmtsMacTable entry including the cable modem notification enable/disable and the interval of cable modem notification sent by the CMTS for a cable modem that the Mac interface supports. An entry in this table exists for each i ...

cdxCmtsCmOnOffTrapEnable

An indication of whether the cdxCmtsCmOnOffNotification is enabled. The default value is false(2).

cdxCmtsCmOnOffTrapInterval

The interval for cdxCmtsCmOnOffNotification sent by CMTS for one online/offline state change if cdxCmtsCmOnOffTrapEnable is true. If there are more than one state changes to online/offline for a cable modem during this interval, only one cdxCmtsCmOnOffNot ...

cdxCmtsCmDefaultMaxCpes

The default maximum number of permitted CPEs per modem in this cable interface. A modem can override this value by setting the object cdxCmtsCmMaxCpeNumber in the cdxCmtsCmTable. The value -1 means the default value of maximum hosts per modem in this cabl ...

cdxCmtsCmTotal

The total count of cable modems on this cable mac interface since boot.

cdxCmtsCmActive

The count of cable modems that are active. Active cable modems are recognized by the cdxCmtsCmStatusValue other than offline(1).

cdxCmtsCmRegistered

The count of cable modems that are registered and online on this cable mac interface. Registered cable modems are those with one of the following values. registrationComplete(6) of docsIfCmtsCmStatusValue OR either of online(12), kekRejected(10), onlineKe ...

cdxCmtsCmDMICMode

The Dynamic Shared Secret feature can operate in three different modes, depending on what action should be taken for cable modems that fail the CMTS MIC verification check: notConfigured(1): It indicates that the DMIC is not configured for this cable inte ...

cdxCmtsCmDMICLockQos

If cdxCmtsCmDMICMode is set to lockingMode(3), this object would contain the restrictive QoS profile number as indicated by docsIfQosProfIndex if set and it will have 0 if not applicable or not defined. In case, cdxCmtsCmDMICMode is set to lockingMode(3) ...

cdxCmtsCmChOverTimeExpiration

The time period to expire a CMTS channel override operation. Within the time period, if the CMTS cannot send out a RNG-RSP message with channel override fields to a cable modem specified in the operation, the CMTS will abort the operation. The possible re ...

cdxCmtsCmChOverTable

A table of CMTS operation entries to instruct cable modems to move to a new downstream and/or upstream channel. An entry in this table is an operation that has been initiated from CMTS to generates downstream frequency and/or upstream channel override fie ...

cdxCmtsCmChOverEntry

A CMTS operation entry to instruct a cable modem to move to a new downstream and/or upstream channel. A CMTS operator can use this to initiate an operation in CMTS to instruct a cable modem to move to a new downstream, or upstream channel or both. Each en ...

cdxCmtsCmChOverSerialNumber

Object which specifies a unique entry in the table. A management station wishing to initiate a channel override operation should use a pseudo-random value for this object when creating or modifying an instance of a cdxCmtsCmChOverEntry.

cdxCmtsCmChOverMacAddress

The mac address of the cable modem that the CMTS instructs to move to a new downstream and/or upstream channel. This column must be set to a valid Mac address currently in the CMTS in order for this entry's row status to be set to active successfully.

cdxCmtsCmChOverDownFrequency

The new downstream frequency which the cable modem is instructed to move to. The value 0 is to ask the CMTS not to override the downstream frequency.

cdxCmtsCmChOverUpChannelId

The new channel Id which the cable modem is instructed to move to. The value -1 is to ask the CMTS not to override the upstream channel Id.

cdxCmtsCmChOverTrapOnCompletion

Specifies whether or not a cdxCmtsCmChOverNotification should be issued on completion of the operation. If such a notification is desired, it is the responsibility of the management entity to ensure that the SNMP administrative model is configured in suc ...

cdxCmtsCmChOverOpInitiatedTime

The value of sysUpTime at which the operation was initiated. Since it is possible to have more than one entry in this table for a cable modem, this object can help to distinguish the entries for the same cable modem.

cdxCmtsCmChOverState

The status of the specified channel override operation. The enumerations are: messageSent(1): the CMTS has sent a RNG-RSP message with channel override to the cable modem. commandNotActive(2): the command is not in active mode due to this entry's row stat ...

cdxCmtsCmChOverRowStatus

The status of this table entry. This value for cdxCmtsCmChOverMacAddress must be valid Mac address currently in the CMTS in order for the row status to be set to active successfully. Once the row status becomes active and state becomes waitToSendMessage, ...

cdxCmtsCmTable

This table contains attributes or configurable parameters for cable modems from a CMTS.

cdxCmtsCmEntry

The list contains a cable modem's attributes or configurable parameters from a CMTS.

cdxCmtsCmMaxCpeNumber

The maximum number of permitted CPEs connecting to the modem. The value -1 means to use the default value of maximum hosts per modem in the CMTS cable interface which the modem connects to and the value is defined in cdxCmtsCmDefaultMaxCpes in the cdxCmts ...

cdxCmtsCmCurrCpeNumber

The current number of CPEs connecting to the modem. The value 0 means no hosts connecting to the modem.

cdxCmtsCmQosProfile

The index in docsIfQosProfileTable describing the quality of service attributes associated with this particular modem's primary SID. When trying to change the value, if the new value is not a valid index in the docsIfQosProfileTable, the modem will retain ...

cdxCmtsCmStatusDMICTable

This table contains the list of modems which failed the CMTS Dynamic Message Integrity Check (DMIC). The modems are either Marked: The modems failed the DMIC check but were still allowed to come online. Locked: The modems failed the DMIC check and hence w ...

cdxCmtsCmStatusDMICEntry

Additional DMIC objects for docsIfCmtsCmStatusTable entry.

cdxCmtsCmStatusDMICMode

This shows all the cable modems that are online or offline and that had failed the Dynamic CMTS MIC verification check. The state is mentioned as follows: mark(1): The modem was allowed to come online. lock(2): The modem was allowed to come online but wit ...

cdxCmtsCmStatusDMICUnLock

When set to TRUE, it forces the cable modems to reinitialize, and the cable modems must re-register with a valid DOCSIS configuration file before being allowed online. Otherwise, the cable modem is locked in its current restricted QoS profile and cannot r ...

cdxCmToCpeTable

This table contains information about CPE connects behind cable modem. It will return IP address and IP address type of each CPE connect to a CM. It is not intended to walk the whole table. An application would need to query this table based on the specif ...

cdxCmToCpeEntry

Represents an entry in the table. Each entry is created if there is CPE connects to a cable modem. The indices uniquely identify a CPE. It is never the intent for an application to perform a SNMP Get operation against a table of this nature, rather it is ...

cdxCmToCpeCmMacAddress

The MAC address that uniquely identifies a cable modem that CPEs connects to.

cdxCmToCpeInetAddressType

The type of Internet address of the cdxCmToCpeInetAddress.

cdxCmToCpeInetAddress

This object identifies the address assigned to this CPE.

cdxCpeToCmTable

This table contains information about cable modems with CPE connects to. It is not intended to walk the whole table. An application would need to query this table base on the specific index. Otherwise, it will impact the CMTS performance due to the huge s ...

cdxCpeToCmEntry

An entry in cdxCpeToCmTable. Each entry contains information on the MAC address, IP Address, and status index for the cable modem with a specific CPE connects to. Each entry is created if there is any cable modem with CPE connects to. Entries are ordered ...

cdxCpeToCmCpeMacAddress

This object identifies the MAC address of the CPE.

cdxCpeToCmMacAddress

This object identifies the MAC address of the cable modem.

cdxCpeToCmInetAddressType

The type of Internet address of the cdxCpeToCmInetAddress object.

cdxCpeToCmInetAddress

This object identifies the address assigned to this cable modem.

cdxCpeToCmStatusIndex

An entry in docsIfCmtsCmStatusTable identifying status index of the cable modem which the CPE connects to.

cdxIfUpstreamChannelExtTable

This table contains upstream channel attributes for automated Spectrum management, in addition to the ones provided by docsIfUpstreamChannelEntry. It also contains upstream channel attributes to count the number of active, registered and total number of c ...

cdxIfUpstreamChannelExtEntry

Additional objects for docsIfUpstreamChannelEntry, including the secondary upstream channel modulation profile, the lower bound for the channel width and the number of active, registered and total number of cable modems on this upstream channel.

cdxIfUpChannelWidth

The lower bound for the bandwidth of this upstream channel. The bandwidth specified by docsIfUpChannelWidth is used as the upper bound of the upstream channel. The two objects, docsIfUpChannelWidth and cdxIfUpChannelWidth, in conjunction, define the upstr ...

cdxIfUpChannelModulationProfile

The secondary modulation profile for the upstream channel. This should be a QPSK modulation profile if the primary profile is QAM-16. The CMTS will switch from primary profile (QAM16) to secondary profile (QPSK) depending on the noise level of a particula ...

cdxIfUpChannelCmTotal

The total count of cable modems on this upstream channel since boot.

cdxIfUpChannelCmActive

The count of cable modems that are active. Active cable modems are recognized by the cdxCmtsCmStatusValue other than offline(1).

cdxIfUpChannelCmRegistered

The count of cable modems that are registered and online on this upstream. Registered cable modems are those with one of the following values: registrationComplete(6) of docsIfCmtsCmStatusValue OR online(12), kekRejected(10), onlineKekAssigned(6), tekReje ...

cdxIfUpChannelInputPowerLevel

The Upstream Input power level at the CMTS interface. This is the expected power level and is different from the actual power received. If not configured the default value is 0 dBmV and is also the optimum setting power level for the upstream. For FPGA li ...

cdxIfUpChannelAvgUtil

The average percentage of upstream channel utilization. This item indicates the running average of percent channel utilization in CMTS upstream Mac scheduler.

cdxIfUpChannelAvgContSlots

The average percentage of contention mini-slots. This item indicates the running average of percent contention mini-slots in CMTS upstream Mac scheduler.

cdxIfUpChannelRangeSlots

The average percentage of initial ranging mini-slots. This item indicates the running average of percent initial ranging mini-slots in CMTS upstream Mac scheduler.

cdxIfUpChannelNumActiveUGS

This object indicates the number of active Unsolicited Grant Service (UGS) on a given upstream. This would be used for the user to evaluate traffic load at any given time of the day. The Unsolicited Grant Service (UGS) is designed to support real-time ser ...

cdxIfUpChannelMaxUGSLastOneHour

This object indicates the maximum number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last one hour. This would be used for the user to evaluate traffic load at any given time of the day. The Unsolicited Grant Service (UGS) is d ...

cdxIfUpChannelMinUGSLastOneHour

This object indicates the minimum number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last one hour. This would be used for the user to evaluate traffic load at any given time of the day. The Unsolicited Grant Service (UGS) is d ...

cdxIfUpChannelAvgUGSLastOneHour

This object indicates the average number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last one hour. This would be used for the user to evaluate traffic load at any given time of the day. The Unsolicited Grant Service (UGS) is d ...

cdxIfUpChannelMaxUGSLastFiveMins

This object indicates the maximum number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last five minutes. This would be used for the user to evaluate traffic load at any given time of the day. The Unsolicited Grant Service (UGS) ...

cdxIfUpChannelMinUGSLastFiveMins

This object indicates the minimum number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last five minutes. This would be used for the user to evaluate traffic load at any given time of the day. The Unsolicited Grant Service (UGS) ...

cdxIfUpChannelAvgUGSLastFiveMins

This object indicates the average number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last five minutes. This would be used for the user to evaluate traffic load at any given time of the day. The Unsolicited Grant Service (UGS) ...

cdxQosCtrlGroup

Group of objects implemented in Cable Modem Termination Systems (CMTS) cable interfaces for states of the scheduler supporting Data-Over-Cable Service Interface Specifications (DOCSIS) 1.0 Quality of Service (QoS).

cdxQosQueueGroup

Group of objects implemented in Cable Modem Termination Systems (CMTS) cable interfaces for the queuing states of the scheduler supporting Data-Over-Cable Service Interface Specifications (DOCSIS) Quality of Service (QoS). Each upstream scheduler maintain ...

cdxCmtsCmCpeGroup

Group of objects implemented in Cable Modem Termination Systems (CMTS) for managing and monitoring cable modems or Customer Premises Equipments.

cdxQosCtrlGroupRev1

Group of objects implemented in Cable Modem Termination Systems (CMTS) cable interfaces for states of the scheduler supporting Data-Over-Cable Service Interface Specifications (DOCSIS) Quality of Service (QoS).

cdxCmtsCmCpeGroupRev1

Group of objects implemented in Cable Modem Termination Systems (CMTS) for managing and monitoring cable modems or Customer Premises Equipments.

cdxSpecMgmtGroup

Group of objects implemented in Cable Modem Termination Systems (CMTS) cable interfaces for automated upstream spectrum management.

cdxCmtsCmCpeGroupRev2

Group of objects implemented in Cable Modem Termination Systems (CMTS) for managing and monitoring cable modems or Customer Premises Equipments.

cdxSpecMgmtGroupRev1

Group of objects implemented in Cable Modem Termination Systems (CMTS) cable interfaces for automated upstream spectrum management.

cdxCmtsCmCpeGroupRev3

Group of objects implemented in Cable Modem Termination Systems (CMTS) for managing and monitoring cable modems or Customer Premises Equipments.

cdxQosCtrlGroupRev2

Group of objects implemented in Cable Modem Termination Systems (CMTS) cable interfaces for states of the scheduler supporting Data-Over-Cable Service Interface Specifications (DOCSIS) Quality of Service (QoS).Statistics about the IE types in the Upstream ...

cdxCmtsCmCpeGroupRev4

Group of objects implemented in Cable Modem Termination Systems (CMTS) for managing and monitoring cable modems or Customer Premises Equipments.

cdxSpecMgmtGroupRev2

Group of objects implemented in Cable Modem Termination Systems (CMTS) for upstream interfaces.

cdxSpecMgmtGroupRev3

Group of objects implemented in Cable Modem Termination Systems (CMTS) for upstream interfaces.

cdxCmtsCmCpeGroupRev5

Group of objects implemented in Cable Modem Termination Systems (CMTS) for managing and monitoring cable modems or Customer Premises Equipments.

cdxCmtsCmCpeGroupRev6

Group of objects implemented in Cable Modem Termination Systems (CMTS) for managing and monitoring cable modems or Customer Premises Equipments.

cdxCmtsCmCpeGroupRev7

Group of objects implemented in Cable Modem Termination Systems (CMTS) for managing and monitoring cable modems or Customer Premises Equipments.

cdxCmtsCmCpeGroupRev8

Group of objects implemented in Cable Modem Termination Systems (CMTS) for managing and monitoring cable modems or Customer Premises Equipments.

cdxCmtsCmCpeDeleteGroup

A collection of object(s) to delete Cable Modem(CM) or Customer Premises Equipment(CPE) in CMTS.