The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for port configuration
- Xylan ATM ILMI Configuration Port
- xylnatmILMIConfPort 1.3.6.1.4.1.800.2.9.1.4.3.1.2 (defined in XYLAN-CSM-MIB)
The port number this entry represents - Xylan ATM Traffic Shaper Configuration Port Index
- xylnatmTrafficShaperConfPortIndex 1.3.6.1.4.1.800.2.9.1.18.1.1.2 (defined in XYLAN-CSM-MIB)
The port on which traffic shaping circuitry resides. A CSM-AB module can have either one or two traffic shaping ports. If the module has one traffic shaping port, then the traffic shaping circuitry is always installed on the first port of the module. - Xylan ATM V Uni Configuration Port Index
- xylnatmVUniConfPortIndex 1.3.6.1.4.1.800.2.9.1.4.2.2.1.2 (defined in XYLAN-CSM-VUNINNI-MIB)
A unique value which identifies this virtual UNI/NNI instance in a specific physical port in the slot identified by xylnatmVUniConfSlotIndex - cbr DS1E1 Port Configuration LBO
- cbrDS1E1PortConfLBO 1.3.6.1.4.1.43.1.12.3.1.1.15.2.1.1.1 (defined in 3comab9300)
This object is applicable to a T1-DSX CBR interface ONLY and indicates the associated Line Build Out configuration for the designated port. An error is returned if an access is attempted on a physical interface other than a T1-DSX port interface. The default value is 330 to 440 feet (4). - cbr DS1E1 Port Configuration Line Code
- cbrDS1E1PortConfLineCode 1.3.6.1.4.1.43.1.12.3.1.1.15.2.1.1.2 (defined in 3comab9300)
This object indicates the zero code suppression technique configured to the specified T1/E1 port interface. The bipolar with 8 zero substitution (B8ZS) technique is applicable to T1 interfaces ONLY. The High Density Binary Three (HDB3) is applicable to E1 interfaces ONLY. - cbr DS1E1 Port Configuration Port Mode
- cbrDS1E1PortConfPortMode 1.3.6.1.4.1.43.1.12.3.1.1.15.2.1.1.3 (defined in 3comab9300)
This object indicates the type of service configured to the specified T1/E1 port interface. Unstructured allows the application to utilize the entire available bandwidth at a bit rate of 1.544 Mb/s for T1 or 2.048 Mb/s for E1. T1/E1 Framing is optional in this service mode. Structured service provides Nx64 kbit/s capability where N ranges between 1 and the maximum number of available DS0 channels. Struct-Voice passes traffic with signaling informaion enabled. Struct-Data passes traffic with signaling information disabled. Changing the mode configuration will cause the following parameters to be changed. . framing timing signaling crc-4 . ------- ------ --------- ----- . T1 unstructured unframed N/A N/A N/A . struct data ESF loop* N/A N/A . struct voice ESF loop* N/A N/A . E1 unstructured unframed N/A disable disable . struct data single loop* disable disable . struct voice multi loop* enable enable * timing is converted to loop timing only if timing is previously . configured to be in SRTS or adaptive timing modes NOTE: Changing this object to a different mode will cause all previously associated VCC's to be deleted. The default value for this object is unstructured (1). - cbr DS1E1 Port Configuration Framing
- cbrDS1E1PortConfFraming 1.3.6.1.4.1.43.1.12.3.1.1.15.2.1.1.4 (defined in 3comab9300)
This object indicates the type of frame organization configured for the specified T1/E1 port interface. D4 and ESF frame organizations apply to T1 interfaces ONLY. Single-frame and multi-frame organizations pertain to E1 interfaces ONLY. An error is returned if a set is applied to an inappropriate cardtype (eg. T1-D4 is applied to an E1 cardtype). Unframed is not a valid configuration in a structured mode. The E1 interface will not allow framing to be changed in structured voice mode. Changing the framing configuration for an E1 interface will cause the following parameters to be changed in unstructured and structured data modes. . signaling crc-4 . --------- ----- . E1 unframed disable disable . single-frame disable* disable . multi-frame enable* enable * signaling is automatically changed in unstructured mode only The default value is unframed (1). - cbr DS1E1 Port Configuration Timing
- cbrDS1E1PortConfTiming 1.3.6.1.4.1.43.1.12.3.1.1.15.2.1.1.5 (defined in 3comab9300)
This object indicates the type of input clock service configured for the specified T1/E1 port interface. Synchronous Residual Time Stamp (SRTS) and Adaptive timing modes are ONLY available in unstructured mode. System configures the port interface to use the system reference clock within the shelf as a reference for transmitting. Loop uses the input port Rx clock as the timing source. An error is returned if an access is attempted to set this object in an inappropriate port mode (eg. SRTS is applied in structured voice mode). The default value is adaptive (4). - cbr V35 Port Configuration Cable Type
- cbrV35PortConfCableType 1.3.6.1.4.1.43.1.12.3.1.1.15.5.1.1.1 (defined in 3comab9300)
This object indicates the type of cable connected to the port. An error is returned if an access is attempted on a physical interface other than a V.35 port interface. The default value is none (1). - cbr V35 Port Configuration Tx Clock Phase
- cbrV35PortConfTxClockPhase 1.3.6.1.4.1.43.1.12.3.1.1.15.5.1.1.3 (defined in 3comab9300)
This object indicates the type of Transmit clock phase needed to correct the clock out of phase problem. This is aplicable ONLY when a 'dte' cable is connected to the port. The default value is normal (1). - cbr V35 Port Configuration Counts
- cbrV35PortConfCts 1.3.6.1.4.1.43.1.12.3.1.1.15.5.1.1.5 (defined in 3comab9300)
This object indicates CTS pin status. Default value is off (1). - cbr V35 Port Configuration Dsr
- cbrV35PortConfDsr 1.3.6.1.4.1.43.1.12.3.1.1.15.5.1.1.7 (defined in 3comab9300)
This object indicates DSR pin status. Default value is off (1). - cbr V35 Port Configuration Loop Back Type
- cbrV35PortConfLoopBackType 1.3.6.1.4.1.43.1.12.3.1.1.15.5.1.1.11 (defined in 3comab9300)
This object indicates the type of loopback configured for the specified T1/E1 port interface. Network-line (2) redirects incoming remote traffic back into the network interface at the external edge of the card interface. Network-card (4) regenerates framing information prior to redirecting incoming remote traffic back into the network interface. Local-card (3) redirects local incoming traffic back into the local system. The default value is no-loopback (1). - Cabletron Translation Novell Configuration Port
- ctTransNovellCfgPort 1.3.6.1.4.1.52.4.1.3.4.8.1.1.1 (defined in ctron-translation-mib)
The MIB-II interface number of the port for which this entry is administering Novell configuration management. - Cabletron Translation IP Configuration Port
- ctTransIPCfgPort 1.3.6.1.4.1.52.4.1.3.4.9.1.1.1 (defined in ctron-translation-mib)
The MIB-II interface number of the port for which this entry is administering IP configuration management. - Cabletron Translation A2 Configuration Port
- ctTransA2CfgPort 1.3.6.1.4.1.52.4.1.3.4.10.1.1.1 (defined in ctron-translation-mib)
The MIB-II interface number of the port for which this entry is administering Appletalk2 configuration management. - Cabletron MMACFENB Configuration Port Group
- ctMMACFENBCfgPortGroup 1.3.6.1.4.1.52.4.1.2.9.2.1.1.2 (defined in fast-ethernet-mib)
The port group for which this MMAC FENB information pertains. - Cabletron MMACFENB Configuration Port
- ctMMACFENBCfgPort 1.3.6.1.4.1.52.4.1.2.9.2.1.1.3 (defined in fast-ethernet-mib)
The physical port for which this MMAC FENB information pertains. - port Speed Dpx Configuration
- portSpeedDpxCfg 1.3.6.1.4.1.52.4.12.30.1.2.1.1.4 (defined in v2h124-24-mib)
according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode hundredBaseTX port can be set as halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as halfDuplex100(4) fullDuplex100(5) thousandBaseSX port can be set as halfDuplex1000(6) fullDuplex1000(7) The actual operating speed and duplex of the port is given by portSpeedDpxStatus. - port Flow Control Configuration
- portFlowCtrlCfg 1.3.6.1.4.1.52.4.12.30.1.2.1.1.5 (defined in v2h124-24-mib)
If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE 802.3x flow control mechanism. If the port type is hundredBaseFX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, Flow control mechanism will not function. (2) Flow control mechanism is disabled. (3) Flow control mechanism is backPressure. when the port is in fullDuplex mode.This flow control mechanism will not function. (4) Flow control mechanism is IEEE 802.3x flow control. when the port is in halfDuplex mode.This flow control mechanism will not function. hundredBaseTX and thousandBaseSX port can be set as: enabled(1), disabled(2), backPressure(3), dot3xFlowControl(4). hundredBaseFX port can be set as: enabled(1), disabled(2), backPressure(3). The actual flow control mechanism is used given by portFlowCtrlStatus. - xst Instance Configuration Root Port
- xstInstanceCfgRootPort 1.3.6.1.4.1.52.4.12.30.1.5.6.4.1.7 (defined in v2h124-24-mib)
lowest cost path from this bridge to the root bridge of the RST . - Enterasys Cos Inbound Rate Limiting Port Configuration Flood Limiter
- etsysCosIrlPortCfgFloodLimiter 1.3.6.1.4.1.5624.1.2.55.1.5.8.1.2 (defined in enterasys-class-of-service-mib)
This object will represent the etsysCosIrlResourceNum to be used to limit flooded traffic. - Enterasys Cos Outbound Rate Limiter Port Configuration Flood Limiter
- etsysCosOrlPortCfgFloodLimiter 1.3.6.1.4.1.5624.1.2.55.1.6.8.1.2 (defined in enterasys-class-of-service-mib)
This object will represent the etsysCosOrlResourceNum to be used to limit flooded traffic. - Enterasys Port Web Authentication Port Configuration Table
- etsysPwaPortConfigurationTable 1.3.6.1.4.1.5624.1.2.8.2.1 (defined in enterasys-pwa-mib)
A table of configuration objects for each port that are supported by the Port Web Authentication Entity. An entry appears in this table for each port in this system. All objects/instances in this table are stored persistent memory. - Enterasys Port Web Authentication Port Configuration Entry
- etsysPwaPortConfigurationEntry 1.3.6.1.4.1.5624.1.2.8.2.1.1 (defined in enterasys-pwa-mib)
The ifIndex number, maximum number of requests, quiet period between failed attempts, and initialization control for a Port. This table holds the objects for configuring the PWA system. - Enterasys Port Web Authentication Port Configuration Group
- etsysPwaPortConfigurationGroup 1.3.6.1.4.1.5624.1.2.8.5.2 (defined in enterasys-pwa-mib)
This section is for ifIndex based configuration of the PWA system. - Enterasys Spanning Tree Diagnostic Cist Port Spanning Tree Configuration Bpdu Rx
- etsysStpDiagCistPortStpCfgBpduRx 1.3.6.1.4.1.5624.1.2.29.1.3.1.1.4 (defined in enterasys-spanning-tree-diagnostic-mib)
The total number of 802.1D Configuration BPDUs received on this port. - Enterasys Spanning Tree Diagnostic Cist Port Spanning Tree Configuration Bpdu Rx Tc Flag Set
- etsysStpDiagCistPortStpCfgBpduRxTcFlagSet 1.3.6.1.4.1.5624.1.2.29.1.3.1.1.17 (defined in enterasys-spanning-tree-diagnostic-mib)
The total number of 802.1D Configuration BPDUs received on this port with the Topology Change flag set. These BPDUs are included in the overall count of 802.1D Configuration BPDUs received in the etsysStpDiagCistPortStpCfgBpduRx object. - Enterasys Spanning Tree Diagnostic Cist Port Spanning Tree Configuration Bpdu Tx Tc Flag Set
- etsysStpDiagCistPortStpCfgBpduTxTcFlagSet 1.3.6.1.4.1.5624.1.2.29.1.3.1.1.18 (defined in enterasys-spanning-tree-diagnostic-mib)
The total number of 802.1D Configuration BPDUs transmitted on this port with the Topology Change flag set. These BPDUs are included in the overall count of 802.1D Configuration BPDUs transmitted in the etsysStpDiagCistPortStpCfgBpduRx object. - Enterasys Spanning Tree Diagnostic Cist Bridge Port Spanning Tree Configuration Bpdu Rx
- etsysStpDiagCistBridgePortStpCfgBpduRx 1.3.6.1.4.1.5624.1.2.29.1.3.2.1.4 (defined in enterasys-spanning-tree-diagnostic-mib)
The total number of 802.1D Configuration BPDUs received on this port. - appn Port Configuration Group
- appnPortConfGroup 1.3.6.1.2.1.34.4.3.2.2 (defined in APPN-MIB)
A collection of objects providing the instrumentation of APPN port information. - Cisco Distributed Director Host Connect Configuration Port
- cddHostConnectCfgPort 1.3.6.1.4.1.9.9.197.1.2.2.1.1 (defined in CISCO-DIST-DIRECTOR-MIB)
A port number, to which a TCP connect test should be performed for each server associated with this host.
